Glad you did a 2wd version of this job. Saved me from looking like an idiot with the shit torn apart and needing that lock nut socket. Got one on order before I start the job. Thanks!

@leonbonczewskijr5988

4 ай бұрын

Is there a big difference from doing the 4wd version besides the lock nut what size socket is it?

thank you so much. you have no clue how much you helped me

Thank - you, This is identical to my 01 and 03 Toy Taco, both two wheel drive E - locker.

@JaboTheMechanic

3 жыл бұрын

Glad it helped!

Thank U very Much! Best Detailed Bearing Replacement! 🎉Cheers!

Good stuff. Keep up the good videos

Good informative video

Great video!

You can also buy a kit from Harbour Freight for $125 instead of 3 or 4 hundred dollars and it is not the same thing that you have but it worked for me and also if you want to and I did, you can do the wheel bearing with the control arm attached to the car if you don't have access to a press and you won't have to wrestle with it

@danielfiore5528

Ай бұрын

Glad I seen this comment because this video isn't done like most I've seen. Gotta love the youthful enthusiasm!

02' gen era sequioa/tundra. Guessing from knuckle and bearing with hub.

Can this press out and in be possible with a 2 foot breaker bar?

Air chisel between the spindle and the race after some heat it will pop right off . just a tip been there a lot

@JaboTheMechanic

3 жыл бұрын

Thanks for the heads up

Is this same tool for Sequoia?

30:05 Toyota Lock Nut Socket SST: 09318-12010 Torque: 275 N·m {2,804 kgf·cm, 203ft·lbf} but in the real world don't use a 1/2 - Impact Wrenches the pin of the lock nut are easy to break off

I’m having trouble removing 4 pin ring. Is too tight 😢

What is the torque for that lock nut on the back that took the special socket?

@italian316

Жыл бұрын

Toyota Lock Nut Socket SST: 09318-12010 Torque: 275 N·m {2,804 kgf·cm, 203ft·lbf}

Would this be the same on a 2002 tacoma?

@JaboTheMechanic

3 жыл бұрын

Yes it is

This was helpful. I may have to do this in the next week or two. Now that you've done it with the spindle out of the truck, Do you think it can be done with the hub still in the vehicle?

@whocares4464

2 жыл бұрын

From what I have seen probably so

@whocares4464

2 жыл бұрын

I'm like six minutes into this lol

@stevenbauer7744

2 жыл бұрын

@@whocares4464 I lucked out, it was just badly worn pads

@santosmacias7089

Жыл бұрын

You will have to remove the knuckle

19:30 When it finally aligns! 😊

@connorsaul5569

3 жыл бұрын

you prolly dont give a shit but if you're bored like me atm you can stream pretty much all of the new movies on InstaFlixxer. I've been streaming with my gf lately :)

@gatlinaries2894

3 жыл бұрын

@Connor Saul Yea, I have been using InstaFlixxer for since november myself :D

@bodhibilly5321

3 жыл бұрын

@Connor Saul Yea, I have been watching on InstaFlixxer for months myself :D

@salvadormarley75

3 жыл бұрын

@Connor Saul definitely, I've been watching on instaflixxer for years myself :)

@T25de

3 жыл бұрын

The SPAM bots 🤖 are getting more annoying

Hey brother. So I did exactly everything how you did it. (Thank you for the video by the way ) But I have some play . A lil movement. And is all tide up all the way . What now?

@JaboTheMechanic

3 жыл бұрын

Like where is the movement at

@HaroldDGlez

3 жыл бұрын

@@JaboTheMechanic it have a play. Side to side . Is hard to explain by text .

@HaroldDGlez

3 жыл бұрын

@@JaboTheMechanic I could make a lil video and show you.

I'm really hoping for yoir respond . I got my car in pieces out there

Is this the same process for 2016 4Runner (non 4wd)

@JaboTheMechanic

3 жыл бұрын

Its a little bit different

@crxk20r59

3 жыл бұрын

@@JaboTheMechanic yeah I just noticed..thanks!

@JaboTheMechanic

3 жыл бұрын

No problem anytime

doesnt matter which way the bearing goes in? you sure?

Name of tool?

Lot easier with a press

Would this be the same with 01 4runner 4x4 ?

@JaboTheMechanic

3 жыл бұрын

It will be a little different

@flavionavar3631

3 жыл бұрын

@@JaboTheMechanic How so? I’d like to know. I have a ‘98 4runner.

Great vid but you need ta buy yerself a vise bro! Ebay offerup marketplace etc get a bigger one than you think ya need!

Man you're going to need a a press and a bunch of shims

Hi, can you list the tools what you using at this repair ! ?

@shadylaster1678

Жыл бұрын

He did mention the tools 🤦‍♂️

@offroadcaravanertraveler6176

Жыл бұрын

@@shadylaster1678 Yes i got it, but wrenching hub nut by impact will damage bearing )

I'm this type of Mechanic use any other tool as a hammer

This mechanic is exactly why I do shit myself. Terrible bro

@alexpage8965

4 ай бұрын

I was thinking the same thing… although the first few times I had to replace press in wheel bearings I ended up doing a similar job as this guy did. I still appreciate him making the video because all of the other videos are for 4x4 tacomas and I was looking for something that showed exactly which little bits and pieces I would need other than the bearing. I have a harbor freight shop press and a box of press accessories so I will be doing it the old fashioned way rather than with an impact. Not good to use the impact to install the bearings, removing is fine but install not so good.

Lord have mercy…how many special tools does it take? Don’t they make and sell the entire wheel bearing hub assembly for a 2003 toyota tacoma prerunner

@alexpage8965

4 ай бұрын

They do, but it’s a hunk of junk peddled by federal mogul…. You can buy a brand new knuckle, bearing, hub, and associated seals/snapring/spacer from Toyota but it will run you about $800. It is very easy to put together with all brand new parts though!

Looks like a total pain in the ass and a bonehead design. Great video though 👍🏻