Extremely thorough videos for techs & home mechanics, thank you, no one else on KZread took the time to remove cam pulleys and show the markings.

@Pete_Tech_

3 ай бұрын

Glad it helped

Glad to see more in-depth videos on HR’s/VHR’s. I also made a video going over this as well but kept it a bit more brief. Kudo’s for showing another perspective on the job

This has been by far the best explanation of a "HowTo" process for this engine.Infiniti G35 DE!! Im going through this exact job on my own vehicle, and have had reservations about how to set the timing properly. Not anymore!!!!!! My mind is now set at ease. Keep posting videos and" how to" Your a good teacher!!! Thank you

@Pete_Tech_

5 ай бұрын

I appreciate the kind words!

@natepressley3379

5 ай бұрын

Wrong! He never even mentions all the O rings that go with this system and they must be replaced behind the second cover assembly. This video is literally only a fraction of the complete job each of these engines will require. Guaranteed facts!

@natepressley3379

5 ай бұрын

Without these O rings you will still have lower oil pressure internally. I've built many of these engines. Every single time the rest of these steps was missed, the engines suffer catastrophic failures. Every single time!!

@Rex-cm1wx

4 ай бұрын

@@natepressley3379can you be more specific? What are the o rings called? What should I look up to figure out what you are referring to?

@NjBoriG35

2 ай бұрын

They are called O rings ​@@Rex-cm1wx

that was super good. very easy to follow and understand. thanks for that one its probably one of the more important ones i have watched. thanks for that one.

@Pete_Tech_

Ай бұрын

Glad you liked it!

Dang man, very nice work on this his one. Thank you

Very very good explanation. I do a ton of these at my shop per referrals from one VQ enthusiast to another in the DFW area. Couple of tips I’d add for some of the less experienced DIY’ers: a pair of chain vice grips can be used to hold the cam gears (phasers/actuators) instead of pulling the VCs to get a wrench on the cams to keep them still. Spray PB blaster or WD-40 on the dowels before removing the timing cover. They’re usually full of crap/oil/rust and the penetrant will break they junk up and make getting the cover off much easier. Also I like to give them a few light taps with a punch/hammer to break the junk up a little bit. Run a few of your front facing timing cover bolts in before you start the bottom cover bolts that go in from the oil pan entrance. You want that pan nice and flush before you start those bolts or the bolt holes won’t be properly lined up and you’ll cross thread them. You don’t want to cross thread those bolts! 10/10 on the video. Couldn’t have explained it any better myself and like I said, probably done this job 25 times in the last 12 months 😪

@Pete_Tech_

5 ай бұрын

Sincerely appreciate it brother! I’ve done like two dozen of these jobs ever, which I consider to be “a lot” haha, but I’m a big VQ guy (obviously if you’ve seen the channel) and so many people struggle with these for some reason. That’s fantastic advice for the DIY-er as well!

@Pete_Tech_

5 ай бұрын

If you tell me what shop your at I’ll drop DFW mentions for you in all the VQ groups on SM.

@babychoppa762

4 ай бұрын

Im in Fort Worth tx where are u located I need a timing chain replacement on my 04 g35

@Slamj32

3 ай бұрын

Question is the water pump an timing same for G37s an G37 ?

Thorough walk through. Thank you

@Pete_Tech_

7 ай бұрын

Glad it was helpful!

Very good video my man

Good video best one I seen great job

@Pete_Tech_

5 ай бұрын

I appreciate it!

I'm going to be rebuilding my first VQ and was wondering for the cam chains is there a tac for the tensioners that I have to pull before doing the main timing chain?

I need to do this job this winter but dreading it lol

@carlosleandry12

8 ай бұрын

Same here, Im debating on only replacing the main chain and not the cam chains.

Greatly appreciate this video . Months ago I did same job . All Z1 parts full timing chain kit . Wasn’t well guided when I went to crank car for got to pull full pump relay and spun a bearing . Not sure where’d I messed up but if I had this video before , doubt it would’ve happened

@Pete_Tech_

6 ай бұрын

Glad it helped

@omytorres4125

5 ай бұрын

Why u spun a bearing u didn’t put it on time?

Gotta say this was really well explained

@Pete_Tech_

7 ай бұрын

Gotta say.. thanks!

@johnmarco5017

Ай бұрын

No he left out important steps in the removal process..

Thank you for doing this. My G37 rattles at idle or low rpm light to no load. It has 100,000 miles on it now. I might have to dig into it.

Thanks so much for the video. I really appreciate it. Im wondering why the water pump when failed leaks from the upper oil pan gasket? Thanks so much

Yes thank you so much 🙏🏽

Great video

Dude I am so grateful I found this video I had both cam banks jump when I released the tension on the primary chain Can I rotate cam banks clockwise or counter-clockwise without fear of valve/piston contact until I am lined up appropriately?

@johnmarco5017

Ай бұрын

No this video will lead you to hell, take it to a certified mechanic

Great job very useful ! For anyone stressing about timing this video is for you ..

@Pete_Tech_

5 ай бұрын

I appreciate that!

What is the timing chain tensioner torque specs I can't find them anywhere....

Thanks a bunch brother

@Pete_Tech_

4 ай бұрын

Anytime!! God bless 👌🏻

How bad would it be if I just replace the main chain and not the secondary chains?? I don't really feel comfortable taking those secondary off and replaicng the tensioners for the secondary? They look pretty fresh

@Pete_Tech_

8 ай бұрын

I do that all the time. Primary chain and components are fine if the secondary’s are healthy 👌🏻

do you absolutely have to count the links after you rotate/spin the engine?? i made sure i was on timing(100% sure). and put timing right back on tdc after i spun it around several times.

@Pete_Tech_

26 күн бұрын

No you do not. I never do. But many people have low confidence when they set the timing so it’s another way to double check that they didn’t miss it by a tooth.

Brass putty knifes are your friend for this job. 6 minimum to avoid any damage from prying.

Complete with regard to every detail explanation. THANKS !

@Pete_Tech_

5 ай бұрын

You are welcome!

So I bought the Concep Z gallery gaskets, They say there also updated and "better" than oem. Should I trust them or return them?? Now Im worried.

@Pete_Tech_

8 ай бұрын

They are. Same company that designs them for Z1. Nissan themselves doesn’t even use the original material that came on the previous galley gaskets pre-2014.

Pete are there any cam holding tools to hold cams in place I’ve got the 3.6 pentastar ford cam lock tools gm cam tools I can’t find any cam lock tools for Nissan

@Pete_Tech_

2 ай бұрын

Yes 17mm & 19mm wrenches with vice grips 😂

@johnmarco5017

Ай бұрын

@@Pete_Tech_ adjustable wrench’s not vice grips, what are you a junior mechanic?

Hey bro can you please make a video on how to replace the VVEL control shaft sensors or moduel/ mortar please

Does it matter if its just a tiny bit off one of the color marks

@Pete_Tech_

9 ай бұрын

Yes, that’s out of time! Not good

can a bad camshaft phasers be the reason a car wont start?

@Pete_Tech_

2 ай бұрын

A completely failed phaser can prevent it from starting and/or can make it run extremely rough. Intake phasers occasionally fail on the VHRs causing a no start but will usually set a timing code as well.

So I pulled the timing cover to do gallery gaskets, chains, water pump, Guides and tensioner I got the marks all lined up one the main chain and everything is perfect but one is off one tooth on the passenger intake gear I put the new chain back Some way just because it ran fine Is it possible when I was turning then engine over backwards with socket on the crank it jumped a tooth?

@Pete_Tech_

4 ай бұрын

Typically spinning backwards won’t cause it to jump time assuming the tensioner is healthy and the chain isn’t stretched. Now if it was definitely off by a tooth, it’s possible your chain was severely stretched. The new OEM chains have timing mark colored links, they need to be set appropriately. That’s in the video 👍🏻

@MRTuning704

3 ай бұрын

@@Pete_Tech_thank you so much for the reply! One last question I set everything on time to the marks with a new oem chain The only thing im curious about is can I replace the oil pump with out dropping the upper oil pan

Hi I just subscribed. I like your video very informative. I have VQ DE and i want to rebuild by myself. Have a question. Do i need to change my gallery gasket? Or can i reuse it? I have 238,000 mileage on my g35 and i started hearing the marble rolling infront of my engine.

@Pete_Tech_

5 ай бұрын

Replace!! 👍🏻

@Pete_Tech_

5 ай бұрын

Replace everything and do it twice: the second you try to reuse parts you will get bit lol

How do you recommend tourqing the bolt for the galley gasket that is under the cam gear?

@Pete_Tech_

5 ай бұрын

Just hit it with a dab of red locktite and tighten as much as you can. It’ll be fine 👍🏻

@johnmarco5017

Ай бұрын

WRONG! take off the cam gears!

If my key is lined up at timing mark on bottom crank am i at tdc or is it possible to be off 180degrees i have 06 altima ser im trying to do it without removing intake

@Pete_Tech_

6 ай бұрын

The only way to reference TDC is verifying all timing marks (crank and cams). The camshafts can be 180 out when the crankshaft sprocket only is at its timing mark.

@johnmarco5017

Ай бұрын

@@Pete_Tech_yeah he knows what 180 out means bud… smh nobody has a degree gauge smh

Im going to have to be going through this too soon so this video will def be a go to, got a solitary p0011 code and sensors are all good. 2013 370z Nismo with 60k.. From experience what could the most common cause to this code? I plan on replacing it all anyways... Going about 15 degrees out of timing😬

@Pete_Tech_

8 ай бұрын

My first guess would be a stretched chain or gallery gasket problem. That’s definitely a considerable amount. Maybe pull the VVT Soleniods and check for debris or metal on them. But I’d recommend going in and doing a refresh.

@JChic-dh1pz

8 ай бұрын

Thank you, will do, solenoids were fine, so refresh it is...

Very greathful

How do you remove the rad cap housing in order to remove cover , Is it threaded ??

@Pete_Tech_

Ай бұрын

It is not threaded. The radiator cap housing is secured by 10mm bolts and it’s held together onto the valley pipe via O-ring seals. It comes apart with a little bit of a fight usually. Make sure to inspect and/or replace the o-rings on the valley pipe. Install with a synthetic lube.

@b1maxc135

Ай бұрын

@@Pete_Tech_ thank you

I’m changing my cam phaser , due to the encoder issue. So does the 2nd chain have to be in time for it to start properly. Or just the main chain.

@Pete_Tech_

5 ай бұрын

BOTH! The chain has marks, and so do the gears. Shouldnt be hard to set in time 👍🏻

@1MrVQ

5 ай бұрын

@@Pete_Tech_ so I’m assuming I’ll have to take the other cam phaser off to set the chains on bank 2 as well. Or just turn the crankshaft ?

@1MrVQ

5 ай бұрын

Hey man I just got it open. What Size nut is that you have on your harmonic balancer on the crank so you can time the engine. I don’t want to get mine jammed and stuck

@1MrVQ

4 ай бұрын

Bro you saved me tons of money. I Changed the phaser on G37. Took me about 2 week with parts and stuff. Labor was a bitch doing it. Brother you saved me well over 2k. Thank you so much. I’m going boost soon btw. So excited 🔥

@johnmarco5017

Ай бұрын

@@1MrVQ do Not turn the cams separately from the crankshaft!!!

Man my 08 g35 sedan has 92xxx miles in here worried about those gaskets almost every day

@justhere4721

3 ай бұрын

Check your oil pressure. If the pressure is too low, might be the gasket leaking. Also look for codes for cam gear position.

I’m doing a chain replacement on a 2004 Nissan maximum 3.5 first time just trying to understand your video

@nemesisanarchy1528

7 ай бұрын

Advice is don’t do it and take it to a shop because ioa fwd vehicle

@Pete_Tech_

7 ай бұрын

It’s the same process but the covers are different and space configuration sucks. Definitely not for the average DIYer, and I don’t say that to discourage you.

My intake cams, skipped timing when I took off chain tensioner first, can I do this set up and it’ll go back to how it was?

@velizarmilutinovic2947

4 ай бұрын

No response one month later 😂 Did you fix it

@Pete_Tech_

4 ай бұрын

Yes, I Litterally explain that in the video 🫠

@jamestapia9057

4 ай бұрын

@@Pete_Tech_ damn zaddy don’t get mad

@jamestapia9057

4 ай бұрын

@@velizarmilutinovic2947 and yea I did lol

@johnmarco5017

Ай бұрын

@@velizarmilutinovic2947 I know😂by that time dude probably towed his car to the mechanic

Does anyone know a reputable shop in western NY for VQs?

What color are the galley gaskets? I found a piece of what looked like brown gasket material in my oil when I changed it today. I was wondering if maybe that's what it was.

@shaquanfrye298

6 ай бұрын

That is definitely part of the oil gallery gasket

@Pete_Tech_

6 ай бұрын

Yes. I’d bet on the bottom left corner of the lower gallery.

Hi! Nice vid, please can u do VVEL 😊

@Pete_Tech_

7 ай бұрын

Vvel in what regard? Lol

@zarja73

7 ай бұрын

How to mount and adjust vvel

gracias

I just opened up my timing cover after I got a p0021 code. It looks like my intake cam phaser is a couple degrees off. Does that mean the chain jumped a tooth? And what does that mean I need to replace? I already ordered a new phaser but should I also order a new primary chain and tensioner?

@SUMMERSGALLERY

6 ай бұрын

Me too 🤣

You connot get that bolt on the 06 without pulling the gears

Are the 37s an 37 the same timing Chan an water pump the same ?

@Pete_Tech_

3 ай бұрын

Identical 👍🏻

Great video. Thank you!! Wherr are you located? Id really rather pay someone to do my gallery gaskets. 🙄

@Pete_Tech_

5 ай бұрын

Minnesota 😅

How do you do the oil pump change

@Pete_Tech_

3 ай бұрын

The oil pump requires the removal of everything in the video, in addition to the upper oil pan. Then it is pretty easy to remove.

Willl this work for a vq35hr motor 2007 350z

@Pete_Tech_

6 ай бұрын

Yes, same exact setup

do the cam chains jump when i take the primary chain off?

@jeffspears8801

4 ай бұрын

Yes...this is what I am currently trying to fix

@Pete_Tech_

4 ай бұрын

No.. bank to bank camshaft timing will move, yes, but the camshaft to camshaft chain cannot jump. In this video I specially address the fact that if the cam timing changes bank to bank, it can easily be reset.

@johnmarco5017

Ай бұрын

Yes it does change, do not attempt this job on your own. Take it to a insured mechanic.

Its confusing how you make the top of the chain tight without having slack I do it and i keep rotating them and theres always slack i cant get it to be tight without it being off time

@Pete_Tech_

8 ай бұрын

There has to be slack for the upper tensioner to go on. But that goes on last imo.

@JustPaypaBaby

8 ай бұрын

I keep doing it and it keeps landing on the 27th link

@JustPaypaBaby

8 ай бұрын

Idk why

@JustPaypaBaby

8 ай бұрын

Nvmm i hot it on point

I’m kind of confused on the part at the end when you count shouldn’t it still have 26 links no matter what ? Like why turn it over 2 times

@Pete_Tech_

7 ай бұрын

Some people are convinced they have to turn the engine over multiple times to check the timing. Turning it over one will not put the cams in TDC, as they spin 1/2 revolution for every crankshaft revolution. So you can put in back in tdc to check marks OR count teeth. Personally, I never do.

@velizarmilutinovic2947

4 ай бұрын

⁠@@Pete_Tech_ Personally you never do,,,, You just have to be special and confuse people even more

@johnmarco5017

Ай бұрын

@@velizarmilutinovic2947 cause he misleading people, I’ve been trying to tell people he doesn’t know what he’s talking about, it’s people like this who make you feel like he knows but then I’m telling you there more than 3 timing marks you have to verify and make sure of before removing anything

@johnmarco5017

Ай бұрын

@@velizarmilutinovic2947 you see how he didn’t directly answer your question? SMH 🤦

@luckybfroze1436

27 күн бұрын

@@johnmarco5017 so do the colored links on the chain matter(after turning engine/setting back in timing)? because i dont see how it would all of a sudden have more or less links in between, when we are just turning engine, not adding or removing chain links?

Could you do a a video on how to swap the cams ? That would be awesome I like your detail work

@johnmarco5017

Ай бұрын

He won’t, he specifically ignores the 4 timing marks on the intake and exhaust cams on purpose.

Okay on your video when you time the 3.5 engine y do you spine the motor after you get everything done . Do you have to turn it

@Pete_Tech_

7 ай бұрын

You do not have to turn it. I never do. But that’s also because I’m certain everything is on point.

Just passed 207k on my g37x sedan I really need to do this for the gaskets that go bad on these but the thought of me opening my engine like that is 😬🤣

@Pete_Tech_

9 ай бұрын

Definitely not an easy project, but it’s doable!

@quinceymorris7942

9 ай бұрын

Don't wait for it to go into limp mode bro just do it haha (it's a pretty difficult job but the car is essentially useless when it finally breaks so really you have nothing to lose and everything to gain)

@markus360s

8 ай бұрын

@@Pete_Tech_👍🏽

@markus360s

8 ай бұрын

@@quinceymorris7942yeah I think I’m gonna either have it done or do it myself

@08HR350z

6 ай бұрын

​@@markus360sI thankfully found someone on the side who did my oil gallery gaskets for me for $700 but shops usually charge $2,000-3000 in labor alone. I'm at 161k and my oil gallery was already falling out so get yours done asap.

Where u located

@Pete_Tech_

2 ай бұрын

Zimmerman, MN

has anyone actually done this, does this actually work ?

❤🎉n

Good walk through video. But work on your audio editiing. I'm half deaf now.....

@Pete_Tech_

7 ай бұрын

Noted!

@EddieZ33HR

5 ай бұрын

😂😂

Video for VQ35DD doesn’t exist even dealership never heard of engine I have 😂

@Pete_Tech_

4 ай бұрын

It will be the same timing system. Nissan doesn’t have any new tricks when it comes to timing. Even the V8 is nearly identical to this.

@velizarmilutinovic2947

4 ай бұрын

@@Pete_Tech_ Well it doesn’t have timing MARKS on the BACK COVER neither it has any marks do you could align with VVT circles ,,,so you pretty much have to GUESS like 10am and 2pm also to be safe gotta remove cylinder 1 spark plug to be sure it’s all the way up so yes it’s definitely confusing especially if doing it first time as I am right now today 2/21/24 lol Another problem is NOWHERE TO FIND PARTS even dealer has to order and when I go to Nissan dealer they don’t know what’s Infiniti then I have to explain 2020 Infiniti QX60 is same as 2019 Pathfinder with VQ35DD engine ,,, but they still stare like deer into light

@Pete_Tech_

4 ай бұрын

The VQDD has timing marks on the cam gears themselves. As well as colored links. Holler at me on Insta if you need help. @ Pete_Tech_

Thank you 👏

@Pete_Tech_

5 ай бұрын

🤝🏻

seem like a ex BMW employee is working at Nissan. making a simple design to a over engineer nightmare. these engines isn't user friendly.

uhhhhhh excuse me but... those are links of color...

enjeyed lol

Another misleading video that’s gonna cause y’all to take the car to the STEALERSHIP, he didnt show you how to properly make sure the engine is a tdc on the COMPRESSION STROKE! before removing anything. These people love to make short videos with the job half done skipping extremely crucial steps, also he’s doing this on a motors that you haven’t seen start after the job. Get a repair manual guys

@Pete_Tech_

4 ай бұрын

😂, please explain your opinion on the difference between setting in TDC prior to removing the timing cover versus after removing the timing cover? I’d love to potentially learn something 👍🏻

@jeffspears8801

4 ай бұрын

Please explain,I am doing this process currently

@arttijerina1269

4 ай бұрын

Why do you say misleading. What did he miss out

@markcabrera12

3 ай бұрын

I sent mine to top dead center after removing the cover, and everything worked fine. You’re just trying to start a controversy.

@johnmarco5017

Ай бұрын

@@Pete_Tech_ Sure Pete, you didn’t verify the exhaust timing marks or intake timing marks with the respective colored links on both chains before removing, didn’t address the fact that the camshafts are spring loaded and will move when the secondary tensioners are relieved, also note guys there is no moving the crank or cams separately in timing, it’s an interference motor. The timing marks need to perfectly match before removal, then obviously before installation. You see just a little after 18:00 he shows you the colored links in the correct position with the mating marks matched? He didn’t do that before removing any of the timing parts in the beginning of the video. That’s were everyone watching this will mess the motor up. He should have did verified like he showed in 18:00 that the mating marks were correct BEFORE removing anything. Pay attention at 16:20 he skips MAJOR steps and goes to pulling the secondary’s off, NONONONOOO you have to make sure ALL. The mating marks are line up before removing anything!! There’s more that the three he showed in the beginning! You see at 16:50 the exhaust cam on bank one moved when he took the secondary off?? Y’all are gonna fak it up following the short hand videos. I told you. This dudes a faking tool. Sorry guys😢

Without removing the entire cover assembly and replacing the o-rings on the back side of the cover and the front cam bearing covers you're literally wasting your damn time even doing this much work. Not hating on your abilities, yet def hating on the half ass incomplete education of what really needs to be done to ensure proper oiling of this engine design. Good luck...

@Pete_Tech_

5 ай бұрын

In my experience, (which may actually be far less than yours), I have not only never seen a failure with those, I’ve never even heard of it being a failure point. There is far more you can do to this engine in terms of replacement/ reseal. If it doesn’t fail, seems that is more of a waste of time.

This is wrong