Cool. Next time you might consider insulators on the engine mounts to absorb the vibration.

@AJRestoration

3 ай бұрын

Yes I did not expect it to be so alive haha.

Dude you should try bigger headers on it ! I bet the sound would be awesome ! 👍🏻

@AJRestoration

3 ай бұрын

I am doing some searching for ideas right now.

Magnificent AJ, what a masterpiece

@AJRestoration

3 ай бұрын

Thank you Jan!

Very cool! Sounds awesome!

@AJRestoration

3 ай бұрын

It does!

Beautiful AJ well done

@AJRestoration

3 ай бұрын

Thank you so much buddy😀

Now you just need to build the rest of the motorcycle.

Good morning from Southeast South Dakota

@AJRestoration

3 ай бұрын

Good morning buddy!

For being so little, it sure can get up and go. Wishing for warmer weather so i can get my two wheels back out on the road.

@AJRestoration

3 ай бұрын

Sending warmer weather over! All the best, have fun!

@stanleydenning

2 ай бұрын

I went for a ride today. The weather was wonderful, today. Tomorrow, rain, rain, rain.

@Thelurpy1

2 ай бұрын

@stanleydenning tomorrow and the next days are in mid 60's, then snow and rain... dang winter doesn't know when to give up!

AJ, I didn't see any oil go into the sump? there is a spare fitting on the side of the crankcase, what is its purpose?

@Engineman_show

3 ай бұрын

Oil should be mixed with the fuel as it does t have lubrication system . The port is just a display and holds the hall sensor for ignition

@AJRestoration

3 ай бұрын

It uses two stoke oil for lube. That fitting is for case vent to atmosphere. There are gears you can buy to modify the engine to pressure lube.

Need to put some weight in the box to hold it down so it doesn’t rock ‘n’ roll

@AJRestoration

3 ай бұрын

I might have to brace the mounts too!

I have the same engine, but the hall sensor broke and the engine won't start. Is your engine OK?

@AJRestoration

7 күн бұрын

Mine also broke, but that was my own fault. I did order a few new ones and its up and running again. I spun the engine over with the power on and the leads were disconnected from the sparkplugs and that killed the hall sensor for some reason.

Looks Good, I am just wondering how the fuel is delivered to the carburetor.

@AJRestoration

3 ай бұрын

The fuel tank is connected with a silicon hose to the small carburetor, the venturi effect of the carburetor pulls fuel up and into the engine while atomizing the fuel.

Yummy. I'm officially jealous. Heee!

@AJRestoration

3 ай бұрын

You should save up over time and spoil yourself!

Very cool, but the steering needs some work

@AJRestoration

3 ай бұрын

Hahaha I would agree!

Way cool😅😅

@AJRestoration

3 ай бұрын

Indeed!

Вопрос ?? на х..у..м это нужно ради того что б посмотреть на него и всё,,,,,,,,??? как он работает)))))))))

@AJRestoration

3 ай бұрын

Это игрушечная модель двигателя, предназначенная для коллекционирования и восхищения.

😎😎😎👍👍👍

$600? No, I think not…..sorry.

@AJRestoration

3 ай бұрын

Its alright, when you look at the build quality, manufacturing, the castings and the attention to detail, not to even mention the engineering work and fault finding that goes into these mini models you can kind of understand its not a cheap toy.

Nice job, engine looks and sounds very powerful especially considering the size of it. what did you use as a fuel?

@AJRestoration

3 ай бұрын

It uses 95 pump gas mixed with two stroke oil for lube.

Seem a bit unbalanced, I'm wrong? 😁

@Misimpa

3 ай бұрын

Not a bit but very or it must be not hard installed

@pfcparis

3 ай бұрын

The firing order can cause vibrations. Car engines are designed to minimize the vibration. It is more difficult in an engine of this size. Besides, the title says motorcycle engine. Motorcycle engines tend to be designed for sound. The angle of the V can also influence the firing pattern.

@AJRestoration

3 ай бұрын

What pfcparis said is correct.

how much HP is that little bad boy putting out

@AJRestoration

2 ай бұрын

I'd say at least 1 to 1.5hp.

Pricing on these are ridiculous. Useless, other than the assembly and decoration.

@AJRestoration

2 ай бұрын

If you take into account the engeneering and manufacturing its price is on point.

@fveggerby

2 ай бұрын

@@AJRestoration Maybe, but still a lot of money on a "useless" object. Buy a lawnmower, or perhaps an old motorcycle, take apart the engine and reassemble. Way cheaper. ;)

@shawnmcquiggan3887

2 ай бұрын

why must it have purpose? it’s a cool expensive toy, if it’s what dude digs then so be it, if i had 600 bucks to kill off i’d have one and run it next to my two old harley’s just for giggles

@AndrewR2130

5 күн бұрын

Not really useless if u have the skill and tools this could easily be added to an rc model like johnnyq90 has done with a different engine