Lmao truck not starting in the intro clip is my spirit animal

@66Duffman

Жыл бұрын

☠️☠️☠️

I drove on a Lincoln Locker for around 30,000 miles, on the street and offroad with my 96 XJ, actually broke the welds lose , and rewelded it and kept driving it, it was a lot of fun trying to make turns in Manhattan! ! Would put my rear wheel on a curb and whip the turns! It would chirp around turns, it looked funny!

@66Duffman

Жыл бұрын

Good to know 😂

this is a very common axle swap for anyone serious about going off road. I would say that this will work well for almost any 4x4. To anyone who is thinking about doing this keep in mind that those lower shock tabs are on backwards but that will work just fine

the reason you kept breaking ring and pinions on the toyota 3rd was beca of the chevy 63” springs. when running those springs you need to have traction bars to prevent any axle wrap. its the axle wrap thats taking the ring and pinion out. had the same problem on my old yota that had the same springs. put traction bars on it and never broke a ring and pinion again.

@66Duffman

Жыл бұрын

I agree and disagree here…axle wrap definitely contributes to busting a ring but stingily believe I would still break em considering how I drive with doublers and a v6

This is what we both should have done in the beginning, about to head out and get the 38s mounted, I’ll post it up when I get them on

@66Duffman

Жыл бұрын

🚀💯🔥

@frankfilippone9679

Жыл бұрын

@Dirtnation Offroad They're going on right now, can't wait!

Nice work buddy!

@66Duffman

Жыл бұрын

Thanks 🙏🏻

Finally! Wontons and 4deez (nuts)

@66Duffman

Жыл бұрын

🔥🔥🔥

Estos videos me gustan mucho, bien hecho ,buen trabajo,saludos👍🍻

@66Duffman

Жыл бұрын

🍻

Not sure if you did but weld the axle tubes to the center section so the pumpkin can’t spin

@66Duffman

Жыл бұрын

😂😂😂🤔

Time for some new wrenching pants hahaha

@66Duffman

Жыл бұрын

Yeah that was the last run for those 😂

In the front used D44 from chevy blazer 75 is passenger droop a d is 8x6.5 bolt

Idk 14bolt spool might be a cheaper then welding via cost of welder an wire ;) lol

now all you need is a 8 lug chevy axle in the front. I bet a 10 bolt with 8 lug and open spider gears would work well or better than that toyota diff

Good stuff for sure. One thing cool about me, my truck came stock with a Dana 60.

@66Duffman

Жыл бұрын

That’s what’s up 🔥

Great to see this back up and running once again. If you need any help with axles and what not plus possible transfer cases I can definitely help ya Dustin.

@66Duffman

Жыл бұрын

Thank you 🙏🏻 you have a shop?

@DesperadoGarageOfficial

Жыл бұрын

@@66Duffman I do on the east coast but I can refer to a few on the west coast thru some friends of mine if needed.

My idol

@66Duffman

Жыл бұрын

🍻💯

Time for a 60 for the front

@66Duffman

Жыл бұрын

If I can find a decent one under 1500 maybe I will 😂

@frankfilippone9679

Жыл бұрын

@Dirtnation Offroad They're out there, just sucks you have to use a Chevy low pinion, you'll find one, hopefully a kingpin

😂😂😂 Dana axles...

@66Duffman

Жыл бұрын

Guat 😂

Why didn’t you re gear when the axle was out?

@66Duffman

Жыл бұрын

Parts weren’t available at the time…and I expected it to be a slow step by step process

ay dios mio thank god the bracket didn't hit the modelo foo

@66Duffman

Жыл бұрын

😂

A small block V8..

@66Duffman

Жыл бұрын

🤔

Check your Instagram messages

@66Duffman

Жыл бұрын

Going now 🤔