This was a fun one! Hope Yall enjoy! Thanks to Sam from @scrappyindustries for helping me get this beauty home!

@rintin1874

6 ай бұрын

Good to have great friends matt , well done Sam helping out again 👍

@aussiegarbo752

6 ай бұрын

I'm sure it was! A very unusual machine compared to your content!

@Spargeltarzan49

6 ай бұрын

Hey matt, i have a rather personal question, what is the best way to contact you for that?

@Dodgeramcummins739

6 ай бұрын

It's great to see you and sam working together!

@ventusprime

6 ай бұрын

You sould invest to walkie talkie, it can come handi

Matt there should be a mandatory cut away in every vid where your Mrs gives her review of the latest purchase 😂

@DieselCreek

6 ай бұрын

That’s a good idea lol

@newrenewableenergycontrol5724

6 ай бұрын

Tried it. The sound track was completely wiped out with all the bleeps!!

@paulprigge1209

6 ай бұрын

I’m not sure that KZread would accept it !!!

@theodoredugranrut8201

6 ай бұрын

Ahhahaha

@jaybrooks2502

6 ай бұрын

Criminal! Great job!

Hey Matt, I work with cranes a ton in industrial construction. Please consider getting some crane outrigger pads if you are going to be lifting anything heavy on a dirt surface like that. They don't need to be fancy, even on brand new cranes I've worked with generally they're just a couple layers of 2x6 made into a circle about 2-3' in diameter. They're generally made in a circle because it makes them easy to just roll around to where you need them. With those small pads on that crane and the amount of force it can put into the ground you risk it shearing the earth and causing the crane to tip over.

@garymallard4699

6 ай бұрын

yeah the pad racks are empty....you need hardwood and usually some plywood between layers.... he might find some on an auction... my crane had lots of pads

@ricardokowalski1579

6 ай бұрын

I am a little concerned that Matt made no reference to a load chart.

@franklinwerren7684

6 ай бұрын

I don’t know… maybe 4 - 6 4x4 steel plates 1” thick with a lifting hook on them… I have seen lots of cranes use them. Also fire departments use 2x2 plates for their outriggers on ladder trucks…

@CaptainRon13

6 ай бұрын

Yeah, definitely needs some jack pads. I’ve used 3’ square, 1/2” steel.

@jenniferwhitewolf3784

6 ай бұрын

Great advice... I have watched a lot of cranes in real life, and on YT... pads are always used. He reads all the comments, and I'm sure will see all these comments, and eventually get some. I have 2 examples of 4 axel wheeled cranes similar to this, but a bit smaller, on our family model RR... they are 1960s era P&H prototypes.

You can just tell that the previous owner loved that crane. It was probably an estate asset that was liquidated at the auction with no reserve because the family didn't know what else to do with it. What a great find man, I'm super stoked for you.

@GeneralSulla

6 ай бұрын

That's why I left everything in a trust to my daughter. She can get the guilts for selling my junk. Causing problems even after I'm gone. 😂

@mattd1188

6 ай бұрын

@@GeneralSulla hahaha

@bennyrest9122

6 ай бұрын

I agree. That's probably why they were both so cheap

@PC-ge5rf

5 ай бұрын

The branding on the crane next to them, with the same color pattern, is for a current company that exists. More realistically, they were clearing the yard for new cranes, as they have much newer models advertised on their website. Auctioning is just an easy way to get a couple bucks for something you were going to throw away anyway.

@mattd1188

5 ай бұрын

@@PC-ge5rf Well, I like my idealized feel-good version better. 😂

Yep-i finished the video and saw the orange paint under that panel by the seat. I used to run this crane. I know everyone else that did too. I could tell you alot about it. She was a good crane, especially with the jib on. Smooth and fun to operate. She's done a whole lot of work in her life. She dont like to stop when yer drivin her down the road because the front axles dont have brakes. Those are the dogs to run yer boom out on the top of the boom.

@DieselCreek

3 ай бұрын

Very cool! Who owned it at that time?

@genesispuredeaf2390

3 ай бұрын

That is so amazing that you recognize this specific crane. How cool is that? You should ask for visitation rights 😎

@kylemaxton1770

2 ай бұрын

What do the two things that flip up on the tip of the crane do? That's so neat you recognize this crane!

@InsideOfMyOwnMind

2 ай бұрын

Wow. That's like connecting with your grade school English teacher when you're in your 60's. What are the odds? I know because it happened to me.

@genesispuredeaf2390

2 ай бұрын

@@InsideOfMyOwnMind that is very cool. I am happy that you were able to experience that.

The bar is for the jib. To slide out the fly section you extend the last section fully. Set the boom tip on the ground to get the pressure off the boom slides. Pull the fly section pin then retract the boom section. It should slide out as you retract.

Matt, the 2 flip over brackets on top of the boom head are to connect to and support the fly-jib via adjustable steel rods, you don't need to worry about them as there is no fly with your crane. The pin behind the boom head is to lock the manual boom extension in its extended or retracted working positions, it is positioned with a level main boom in the correct sequence under power using telescope function. Do you have 4 pins in the tackle box for locking the outrigger jack cylinders which are not fitted with check valves, as I note in the video they have not been inserted and the crane is not safe for lifting unless they are fitted. Both hoist ropes show significant surface rust and likely are poor condition internally, you should consider changing them out to prevent a load failure. The main hookblock is missing its safety catch to stop lifting cables from becoming detached. If setting up in your yard you will need good cribbing blocks or steel plates so the jacks don't punch a hole in the ground when lifting, also does the crane have a working rated capacity indicator fitted ? There should be 2 independent means for control of slew system, the hand lever you operated should mechanically engage the swing lock device directly at the slew ring gears/teeth and there should also be a foot pedal to hydraulically actuate a brake near the swing motor. You will need to obtain and carefully read a complete operator manual before using this machine, despite the above comments for $3500 it looks a good buy.

@theda850two

6 ай бұрын

AlanK, relax it's just a demonstration lift .

@LeoA2600

6 ай бұрын

@@theda850two It all sounds like good information that I imagine Diesel Creek will appreciate.

@theda850two

6 ай бұрын

@@LeoA2600,, you're right. We all need watching over.

@johnk2866

6 ай бұрын

Thanks for sharing. Knowledge from experience has no substitute.

@GlobalistJuice

6 ай бұрын

@@theda850two Nah, it's not "watching over", it's a direct response to a request in the video, Matt asked if anyone in the comments had information on a few things of which @alank2296 addressed nicely.👍

I don't think you could rent a crane that size for a day for that price. Great buy!

@xephael3485

6 ай бұрын

Likely not rentable as they wouldn't let novices operate it.

@administratorshan

6 ай бұрын

@@xephael3485wet hire

@MrAllstar

5 ай бұрын

@@xephael3485I’m assuming he meant standard crane rental where they send an operator with the crane, you don’t operate the machine.

@richardotero2376

5 ай бұрын

I was going to say. Rent it once. U get ur money back. Twice is profit. Kids in the neighborhood would pay to play on it. Lol it's the coolest ever

Plenty of people can talk the talk but far fewer walk the walk - this guy is wearing out boots!!! Buys a crane pretty much sight unseen and proceeds to tinker around to the point where it literally comes to life. No doubt his commonsense and ability to think things through stands him in good stead - well done and enjoyed the video!

Hi Matt, the bar is I believe for a "Fly Jib" it is a Lattice form and If I remember it is about 30 feet long. it gives you a much better reach and also allows you to offset further. You have a fast line now and also the headache ball, As I watch I see you have now a Main Block that is the one for the big lifts you intend. Please look inside the cables for corrosion. the core of the rope needs to be lubricated as it will give much more life to your lines. I worked extensively with that type of crane for years back in the seventies it is a great machine I also see you have good sling brothers which is fantastic!I will see if I can find the lifting ranges for this setup you have and for sure get a chart for safe lift loads/ranges!. but perhaps you already have that? I strongly advise you to test the overload bell! and never turn it off!! (I have seen them go over and it is not a happy ending) the previous owners have kept it in good condition, as a preventative maintenance why not cover the coiled cables when left for a long while? (pour clear rope oil on all the rest, clear because you will find it dripping all over your great-looking machine! You gave me a lot of happy memories looking at that old lady working thank you ... remember it is all about the angle of the dangle!

@josephking6515

6 ай бұрын

_"plus the mass of something"_ Mmmm, I would *_debate_* that. 🙄 (sorry, somebody had to reply like a 14 year old schoolboy. 😁)

@howardg7162

6 ай бұрын

Yea what he said

@davidnoseworthy4540

6 ай бұрын

hee hee, not going to "add" anymore, but that little jingle came back to me and made me giggle. Thanks @@josephking6515

@Mr.PudgeMuffin

6 ай бұрын

Since you're experienced on these cranes, could you tell me what the spinning knobs on the line controls are for? Im assuming its to count the length of line going in or out but I wasn't sure.

@ionstorm66

5 ай бұрын

​@@Mr.PudgeMuffin They show you how fast the drums are spinning, to let you know the cable is moving. If youre lifting blind say over a building or behind a wall, you can't see the load moving up or down, the knobs let you know the cable is actually moving, and how fast.

Memories+. Back in the mid 70's, I helped move a Grove crane 175 miles at a top speed of 35 mph. We took five 55 gallon barrels of diesel to refuel, not knowing where we could get any along the way. It took 9 and a half hours, and 4 drivers to get it home. And 2 days to recover from the trip. We fueled up at the bottom of Evansville hill and filled up again at the top of the hill, 55 gallons. 5 to 6 mph. Thanks for letting us come along.

Hey Matt,you got a good deal on that crane for sure. Im a retired heavy lift crane operator with over 40 years experience,I have operated many of those old Groves back in the day. Make some good outrigger pads so you don't sink, put 4 parts on the block, probably all you need.Know the weights of what your lifting and study the charts.Most of all be safe and careful.When things go wrong with a crane, its usually not good!

@brianwheway1933

6 ай бұрын

yep, they usually end up on youtube as "ultimate fails" or "when cranes go wrong"

@henrinaths1

6 ай бұрын

Yup I have a ton of ‘not good’ stories.. Mechanical failures to experienced tag line personnel gone wrong, thinking they’re god’s gift to crane ops.. hospitalized from a near dead bad day. Most tho had to have a relatively harmless diaper change.. lol.. Nuf said!

@ryanweinkauf6661

6 ай бұрын

I was thinking 4 was probably all he needed as well. Line pull 12,000?

@weh365

6 ай бұрын

3:02

@danp7405

6 ай бұрын

?@@weh365

An idea for the roof project, add another container on both side and add a stair case so you could have 2x the storage and 2x the roof height. Just build a staircase on the end to get up into the upper container.and have the entrances opposed

@davidrowe5822

Ай бұрын

Awww crap! I didn't see this comment until now! I just said the same thing an hour ago! LOL Great minds think alike. He will save a lot of fabrication steps by shuffling containers with his new crane! Although I think those are the 40' containers so...Maybe he's got extensions for the sling brothers.

FORD to the Rescue! Sam is an awesome guy to have for a buddy! Thumbs up to Sam! 👍

@DieselCreek

6 ай бұрын

You got that right!

People just out here driving absolutely ANYTHING they want on the open roads. Its honestly inspirational

@MrPerry61

6 ай бұрын

America! 🇺🇸

@thisolesignguy2733

6 ай бұрын

Murika! YEAH!

@Notsofatamerican

6 ай бұрын

Not in the California country.

@ncreamer1

6 ай бұрын

Wish it was done more instead of "in mexico"!!

@normhowes2975

6 ай бұрын

Be nice to my vehicles LOL

From a retired LEO, be advised that thes cranes are usually overweight on most streets. Be careful with that. The rickets can be expensive.

$3,500??? What a score. It will pay for it's self many times over! !! !!!

A proper crane indeed. Pick that roof, double stack the containers and set it back atop like toy blocks. Very cool piece of equipment.

@born2soon

6 ай бұрын

I was also thinking he could double stack the containers as well and then set the roof back on. Maybe go Andrew Camarata on it with a half bath downstairs.

Everyone needs a friend like Sam!!

Great purchase! Be careful at all times when operating a crane, they can easily kill you and anyone around you. Be safe! 🙏

I was just about to type. "It's a good Ford commercial". when you said it.

Matt and Sam together you are unstopable. The dynamic duo. Love watching you guys work together.

Matt, It's doubtful you'll ever have that fly section out, because with that much stick out lift capacity really takes a hit, but if you do run it out make sure to follow the manuals instructions. The worst accident I ever saw with a hydro crane, happened because the fly wasn't re-pined after it was extended, causing that section to drop on a worker below. Get the manual, always check the load chart before doing any heavy lift. If you know a qualified operator, it would be worth it to get instructions on safe operating procedures. It's tempting to just wing it, like we do on most equipment, but a crane is a whole different thing as it and an inexperienced operator can cause injury and death so fast. Nice crane though.

@cliftongilmore145

6 ай бұрын

You're absolutely right, friend, a Crane is a totally different animal. You can wing it with just about anything else, but not a Crane, my friend!!!

@4Him4u2

6 ай бұрын

I agree entirely. We want you to stay safe.

@Jay.Kellett

6 ай бұрын

So right guys. The second you take something for granted and "assume" you know what your doing it bites you in the ass big time. Scaffolding "seems" simple, but make one mistake and someone gets hurt or killed. And, forklifts seem simple too, but if you don't understand the physics and limits, one simple mistake bites you.

@Drakedrakonis02

6 ай бұрын

it looks like an old 40 ton and yah the manual was not needed most of the time we had one in out company for many years its a great workhorse

Now that you have a capable Crain you can take 4 20' boxes and put 2 40 footers across and make shelter for some of your outdoor unprotected equipment to shelter them from rain, leaves , snow, ice, wind. This will also reduce your occupied space by 2/3 at the minimum . It is what they do at the ports.

You could lift the roof off the shed, add another row of containers and lower the roof onto them. More height and more space. Thanks for vid.. always great.

@johnnunn8688

4 ай бұрын

Accessing the upper containers might be a problem though 🤷‍♂️.

@davidrowe5822

Ай бұрын

@@johnnunn8688 Naw....He can just leave the boom arm out and walk up and down the boom! AmIright? :)

Matt, that crane is one of the best purchases you have made in a long time. You will put it to good use soon. Sam is a great friend and very knowledgeable as well as an encouragement. Blessings to you and Sam.

Having owned and worked the smaller TM180 Grove crane-- I STRONGLY suggest you find an original Grove Owner's manual. there is a lot of maintenance information and also safety checks.. Also-- the hydraulic jacks are rated to lift the crane for levelling but NOT lifting over-- they jacks require lowered onto the pins or the seals will get blown...

@PeterChapman-rg6gr

6 ай бұрын

Having owned a number of this era Grove cranes in the Uk i can confirm that Gove stopped fitting these outrigger pins around 1972. In the 27 years of running these we never had an outrigger jack seal blow.

I picked up a 1985 P&H 30t T300 30t hydraulic truck crane. Best thing i bought in along time. I drove it 200 miles with no issues. Runs and operates better than most newer cranes i run. Private use is great, running it commercially is tricky to find insurance. It took two weeks to get a quote due to they did research on my work history, tractor trailer insurance history and my CDL history. 4k for 2 mill annually which is great. Best part is maintaining it myself. Congratulations on the rig

Since the main cable looked like there was a possibility it was broken off, but not sure how much, it would be well worth the time to raise the boom all the way up, extend it all the way out, and lower the block to the ground to be sure there’s enough cable on the drum to reach and still have sufficient wraps on the drum to hold fast! Not a bad idea to slide that jib (extension?) out too while checking the cable length, even though you don’t plan on using it. I’ve seen some nasty things happen as a result of “short” cables over the years! Also beware of “double blocking”, which is lifting the headache ball or main block to the point that they bottom out into the point sheaves or guides! That can cause major damage or catastrophic failure, and this crane is too old to have the OSHA mandated “anti two block” detection on the boom point. One heck of a deal here, and just what you need! It’s often cost prohibitive for companies to bring these older cranes up to the required standards of modern days even though the machine might be in excellent condition! This thing probably sat for years while the company debated updating it, but ultimately threw in the towel!

@robertpaulineglenn3328

5 ай бұрын

Good -onus mate good to see the one girl fire up again.

@robertpaulineglenn3328

5 ай бұрын

23:46 😮😮😮. To. All. I enjoy these Shows.

@Iaintwoke

5 ай бұрын

Also depends how much work it's done. If it requires anything like a slew ring it's probably not worth it. Yeah sorry probably should have read your whole comment first...😂

Hey Matt, I'm not a crane expert, but troubleshooting hydraulic mobile cranes is what I do for a living. I'm not familiar with that model (and especially not that swing brake), but I do know that we have gotten both digital and paper copies of manuals and schematics for our old Groves from our local Grove dealer. You might try giving them a call and asking for the Operator Manual, Service Manual, Service Maintenance Packages, Parts Manual, Schematics, and Load Charts and they can get you that stuff by machine serial number. I'm not sure what they'd charge you, but that information is invaluable for a proper crane like that. Grove manuals are generally very good with explaining theory of operation but not always accurate on specifics. We had an issue with the number of springs in the hoist brake (ours took 9, not 6 per the manual, and we found that out at load test LOL). Feel free to PM me with questions if you want and I'll try to help you out.

@MFKR696

6 ай бұрын

I second this. Those old Grove manuals, if you can find them, are a god-send. They didn't leave a stone unturned.

@ChrisHarding-lk3jj

6 ай бұрын

Unless you get one of those weird grove cranes built in Korea.

@Compasscard

6 ай бұрын

Indeed, having a load chart may also prevent stupid mishaps, guess those cranes don't have an overload protection apart from the operator sense of orientation.

@MFKR696

6 ай бұрын

@@Compasscard The "overload protection" was simply its ability to start tipping before it breaks. A new one will just break, shortly after beeping fiercely at you lol.

@m14lvr

6 ай бұрын

Manitwoc is usually pretty good about having diagrams and whatnot.

The smile on your face when you hear a engine run, it is contagious. It makes us smile too.😁

Hi, nice crane with a lot of potential, I did some repairs on a couple of this GROVE models some years ago, I recommend you to get an LMI for the crane to make it safer when operating and also to prevent accidental snaping on the cables and stressing the crane overall, I Know the electrical system is very basic but a general check up wont hurt, it should be nice if you can upgrade at least the fuse boxes since they always give some troubles, also check on the electrical swivel. Best Regards.

The lever to the left of the seat is probably the swing lock and not a brake. The Grove RT522 that I had the pleasure to operate had a similar control that drops a large pin which locks the swing for travel. Pulling the lever up drops the pin and pushing it down lifts the pin.

I laughed when I watched you pay out that cable using a rope attached to the controls and instantly felt better about some of my more questionable life choices! 😅

@Lnmwr

6 ай бұрын

Yeah that was funny!

Matt - the shot of the drone coming out of the container was excellent. Have a great day and God bless

@DieselCreek

6 ай бұрын

Thanks! I was pretty proud of that one!

@russellashburn6268

6 ай бұрын

I was going to say the exact same thing.

@russellashburn6268

6 ай бұрын

@@DieselCreek you should be proud, it was awesome!

Another fun scenario: Power Company: "We'd love to hook you up, but we don't have a crane!" You: "Hold my beer."

What an incredible deal! I almost cannot believe your good fortune in getting this crane for the price you did! Way to go!

Might wanna make some landing pads for your outriggers to give a bigger foot print. The ones we have at work are made from railroad ties

@SudosFTW

6 ай бұрын

that's actually a splendid idea.

@chrisduncan2626

6 ай бұрын

@@SudosFTW better to do it and be safe that have one sink into the ground and risk the crane turning over

@KnugenMooMoo

6 ай бұрын

Just what I was gonna comment landing pads are your friends Matt

@MitzvosGolem1

6 ай бұрын

Always even on pavement as per Nccco ANSI codes . I flipped a RT over a Lorain punched through asphalt. Was a void under it .

Having Sam as a good friend and fellow mechanic is such a blessing for both of you. I know it took time to develope such a friendship. I'm very happy for both of you. Great job getting the crane home.

I was sweatin bullets with ya when you missed the gear up the hill. Thought you blew the transfer case! Glad you made it home! when you lift the roof off the shed: Maybe keep it simple and just stack one more shipping container on each side and reattach? you'd get your height without the wobble of the legs. Besides...You gotta keep the look. Its what built your channel!

Did anyone else see the ladybug at 34:42 ? 😂😂😂

This young man seems to be so resourceful in doing things single handed ,its astounding.

@ez1913

6 ай бұрын

Nothing to it but to do it.

Remember Matt, Two stroke Detroit's get straight weight oil! Multi vis gets around the rings too quickly during warm-up and you end up with stuck rings. At one time Detroit made mulit-vis recommendation but then people had problems and they went back and changed the recommendation back to straight 40 or 30 depending on temp. Chevron Delo 100 or Shell T1 will do. TSC has the Shell usually.

Hi Matt, I was around way before you started the container shelter workshop. a few years later, now look at what you have. I dont know much about cranes as i'm only a dumb Airline Pilot. Love the content keep it coming.

I’ve worked around cranes for almost 30 years and a few suggestions (I’m sure Matt has already thought of) before really utilizing that crane: 1. Reach out to the manufacturer and they can send every book, manual, tech sheet, and load chart associated to that crane. The load chart is critical in itself but if you ever use the jib, you’ll definitely want a load chart. 2. Get some crane mats to distribute the load path to the ground. 3. Not knowing the age of that cable, it would be worth the money to replace it, if nothing else for peace of mind. 4. If there are no inspection records, I would suggest having the boom sections and outriggers inspected by a licensed professional. For $3500 you definitely came out winning on that deal no matter if you keep it, sell it, or part it out. Another great video showing old stuff is pretty cool and useful.

@davidjones8680

6 ай бұрын

This is extremely sound and wise advice given here Matt.

@apersunthathasaridiculousl1890

6 ай бұрын

I’m pretty sure he’ll make that $3500 by just selling the wheels lol

@Top5cring

6 ай бұрын

​@@willyberg123Better to be safe than sorry with a lot of heavy unforgiving steel.

@Fetguf

6 ай бұрын

My first thought was, that it has a crack in the boom, and it is why it is so cheap. Get the crane part inspected by a licensed professional, before you try and lift something with it.

I'm SO happy for you Matt! This crane WAS an absolute steal!! My gosh, you can't even buy a good, reliable car these days for $3500! I can't wait to see what projects you have lined up for this gem. Enjoy!!!!!

@bobroberts2371

6 ай бұрын

Thing is, as machines get bigger, the market for them gets smaller and the cost of end of life / trailing edge tech gets lower.

@silverbackag9790

6 ай бұрын

@@bobroberts2371yeah, you can buy a used big assed excavator for what a used mini ex costs with comparable hours. Not as many people have the licenses, equipment, etc to move the big ones…or to work on them. But a 5 ton machine can be moved with a F350 and a 14k trailer…and without a CDL with farm tags in many states.

@bobroberts2371

6 ай бұрын

@@silverbackag9790 Yep, you stated the example that I was thinking of.

As a totally non-mechanical person I really admire your ingenuity.

Well done on an excellent buy. I see in the comments that you have some good advice to follow up on. Regarding the lifting cable: It will have a safety factor greater than 3 times it's load rating. You should check exactly what the U.S. regulation is on this safety factor. In the UK the factor is 11 times. As a rule of thumb, you don't need to worry too much about its condition until you see/feel broken strands, so it would be good start to pull it out from the drum to check and oil while you do so. Normally steel lift cable is wound around an oiled sisal core rope. When this dries out the corrosion problems and breakages accelerate. Great video.

Those bars on the Cat head are used for the wires on a fly Jib, the brackets underneath on the main boom are used to stow away a fly Jib...they are a handy addition as they are offset ...

@clarencewiles963

6 ай бұрын

I think you are a person to help the blind man see. 😊

@glennfryer1539

6 ай бұрын

Make sure your SLI Safe Load Indicator works, you only get one go in a Crane !!!!

@DieselCreek

6 ай бұрын

I don’t think I have one of those lol

@clarencewiles963

6 ай бұрын

@@DieselCreekI think you two need to talk more.

@billygraysullivaniii200

6 ай бұрын

What model is it?? I think I have a brochure for it.

You never fail to brighten a man's day with your videos, keep it up and may you keep in good health. greetings from 🇨🇭

@DieselCreek

6 ай бұрын

Thanks, you too!

@pacificcoastpiper3949

6 ай бұрын

@@DieselCreekyeah Matt. I’m going through a family tragedy, so this sort of little bits of joy is WELL loved

@pacificcoastpiper3949

6 ай бұрын

@@DieselCreekAmerican redneckery at its finest. Love it

@switz-3d396

6 ай бұрын

😳 I‘m not the only Swiss guy here!?!?

@Harry_Gersack

6 ай бұрын

So probably I'm not the only german huh?😂

Im 56 and can remember multiple stick cranes in the mid 80s i was not an operator but buddies family had 6 to 7 different sizes. Id move them from job to job because 2 operators had DUIs and couldn't drive them on public roads. In 1996 I can remember picking up a brand-new monster joystick no 15 handles 😂Red chromed out beautiful machine. My girlfriend drove me followed back. We stopped for fuel at a new Exxon huge station with neon a lot of lights clean brand new building. A new clean Kenworth day cab pulling nice stainless trailer was filling ground tanks. no other vehicles in parking lot. My girlfriend amateur photographer stood on a hil took several pictures at dusk mtns in background. Framed one for owner. Many people thought picture was picture of model scale diorama because truck, crane building was so new and clean. Best picture she ever taken. An Exxon rep heard about picture saw it paid hear to keep and use for ads. Like $1500 she jerked his arm off grabbing that check. yove probably seen it and didn't know.

The pin is for your second last boom to extend, the two red flipping bars are for the jib connection and you have already mentioned it correctly in the vedio. Right on.

The brackets on the boom are for the jib. You are right about the manual 4th section which can be extended hydraulically if you do it in the right sequence. Best of luck with your new toy but be very careful of what and how you lift a load. Tipping over a crane is never a good thing as you well know.

@Nebbia_affaraccimiei

6 ай бұрын

I'm guessing these don't have any load sensing of protection to prevent u from doing stupid stuff

@kieranosullivan02

6 ай бұрын

​@@Nebbia_affaraccimieino these were built before that 😂 so I guess in a way they were the test monkeys

@clydeacor1911

6 ай бұрын

I'm pretty sure that doesn't have a 4th section. I have a rough terain Grove crane and that pin is what holds that head to the boom.

@johnsnow1355

6 ай бұрын

I guess u can pull the pin out and pull in the boom from full extension and see if it slides out or falls off 😂

@valfleck7523

6 ай бұрын

Scope, boom down, tie tip onto a truck or tree pull the pin, scope in put the pin in.

You've certainly come a long way from building the container shed 👍

@med1273

6 ай бұрын

KZread MONEY HAS WENT TO HIS HEAD LIKE DRUG DEALERS THEN KZread CRASHES HE WILL NOT BE ABLE KEEP EVERYTHING UP. AND THEN ASK HIMSELF WHAT HAPPENED TO IT ALL . I KNOW FROM EXPERIENCE. IT WILL NOT LAST FOREVER . SAVE YOUR MONEY BUILD YOURSELF A SECRET STASH I WENT LIKE HELL FOR SEVERAL YEARS THOUGHT IT WOULD NEVER END WRONG

@kenc1800

6 ай бұрын

I certainly agree! So glad that Richie Bros. Are so close to you! I see a container house in the near future…. You have the 40 blue ones and now 20 ft. Green ones. Now have the means to rake and stack them. Before long you will just like in READY PLAYER ONE.

I wish i had one of these cranes. Id take out the pistons, change the seals and sell those and build a mobile home on the back.

Hollywood level cinematography without costing 10's 0f millions of dollars, makes you think, where does all the movie budget go, maybe there is some money laundering going on. Fantastic find and video, Cheers.

It was weird seeing you buy something that didn’t need a lot of work. Great buy at a great price. Love watching your videos😊.

Man flying a drone, from the cabin of his $3,500 crane whilst suspending a container...... Life don't get any better than that ! :) Thanks for another great video Matt

It's old and was probably designed by a dude with ruler because it's square as hell, and it has no bells and whistles, but it's clean and straight as a pool table and that's why it's so charming. He should dry ice blast it and give it a nice paint job, pimp both cabins and fit led lights all arround, and maybe a different grille and a bullbar in front of that.

Yeah Matt, I love your new toy. Can’t wait to see it more in action. What’s happening with the auto car and not showing that anymore why I thought by now you’d have it finished painted and everything. I would love to see that finished Philip.

I find myself tackling more "jobs" around the house after watching you Matt. The pull starter rope broke on my lawn mower and I thought about junking it and buying a new one, Then I thought..."What would Matt do?" Fix it of course! Found some 3 mm nylon braided rope in my shed, took the recoil starter assembly apart (interesting bit of engineering) and replaced the broken rope. Works fine.

@allanmck

6 ай бұрын

And when the whole unit goes you can replace the whole recoil starter as well. I tend to go through 1 every few years as I buy cheap plastic jobs considering the state of my obsolete mowers haha.

@matthewromano8801

6 ай бұрын

This is how our forefathers did it. We fixed what was broken, not throw it out and replace it.

Best fuel pump install I've ever seen!

Replaced Fuel Pump Check Pass Dot Inspection Check Give her all the Beans Check She Moving Now Boys 😂 give her all the horses 23:15 @Diesel Creek

If you put a new seat 💺 in it the value would go up by $30,000. 😂

@frank-t6857

6 ай бұрын

And a windshield

Easily worth the money just from the motor, driveline and scrap value

@carlnelson3893

6 ай бұрын

I can't imagine how much each of those hydraulic lifting cylinders go for!! What a deal!

Hi Matt I have been driving and operating cranes for 40+ years so if you need to know anything just get in touch. the main block is missing that one you have is the headache block known as that as it is so small you keep banging your head on it when doing maintenance or rigging. Now I have seen the video I suggest you have 4 falls in not the 8, loads will lift faster and you won't run out of rope when full jib is out. You done well with the pear and anker. the bars are for the flyjib as is the extra sheeath on the cathead.. the Manuel pencil jib is easy to get in and out you can pull out by hand or use one of your plants, to get it back in use the winch rope to pull it in. Keep up the good work mate.

All this baby is missing is a telescoping counter weight for when your doing full boom out near horizontal like picking up a long roof from some shipping containers 😮🎉

I’d make that my daily drive Matt , passenger’s can’t bug you when they need to sit in a different cab 👍🍻

When you started up that grade and was bogging out..my clutch leg started quivering and was instinctively moving my right arm trying to help you grab a gear. The engine sounded really good at the start and I was hoping for the best. By the time you got to the top I had slugged most of a coffee mug down making this video a 2 mugger..Really nice editing and the transitions were a nice added touch along with the container drone. Good job Mr.Matt!

Sketchy trip home but you two nailed it. Maybe look into a Towmate light bar for the rear of your machines to help with hazard lights & flashing ambers at times like this. Also I highly recommend DICA mats or 4x4 or 6x6 swamp mats for the crane.

That turbo Spooling Just sounds So dang Good Matt Spicey 8:20 @Diesel Creek

That f450 pull was pretty damn impressive! 😂

Can't imagine the look you would have gotten from the wife if you bought TWO cranes.

@philipcable437

6 ай бұрын

I think by this point she's resigned to the fact Matt loves a bargain.

@gregbridges2365

6 ай бұрын

😂 it would of been worth the look though

@Roger-hq1yt

6 ай бұрын

Paint one pink and say its her Birthday present, then get her to drive it, your " can she drive it " videos are hillarious, she,s a champ!

@truthislam6481

6 ай бұрын

@@Roger-hq1yt Yeah. I miss seeing Miss Eva trying her best to help out. She is such a GOOD WOMAN!

@garycolemanml

6 ай бұрын

paint one pink, for her. :)-

24:35 this song and view, plus the crane, gives me MASSIVE, and i mean MASSIVE “king of the road” “18 wheels of steel” video game type vibes. I felt like being a kid again and having fun playing them. Thanks for bringing back the memories.

Great buy Matt!! I would suggest to replace the fuel filters on the DD 4-53. That should help with the misfire on the little engine and get better performance. 40 yrs of diesels. Especially Detroit Diesels and Internationals. Great content!

I love the look of this thing. Looks a lot like a huge metal Tonka crane i played with in the 90s in the dentists waiting room

I know how you blokes felt, whilst in the Australian army we had a crane which would only do 35mph flat out. We eventually discovered that it had extra fuel filters (under the cabin)once we replaced them, we could wind the old speedo past the max which was 60mph.

@johnnunn8688

4 ай бұрын

You mean 96kph, Shirley? (You sure you’re an Aussie?)

Looks pretty awesome. As a former oiler/rigger never wear a ball cap while driving that old girl. Hit a bump and you'll push that button on top into your skull. Quite painful.

Maybe just wire up a 12 V connection from the main batteries to the crane portion, so you can just flip a switch and start the crane engine with the main batteries. So you don't need two sets of batteries and if you need the crane engine you usually drove a while anyway, recharging the drive batteries again before you need them. Also allows you to run e.g. the hazards continuesly while you're working without depleting the drive battery.

I watched you put up the roof between your original 2 containers, and looking at your ending aerial view of what your buildings and machinery are now is a fantastic achievement. I'll bet that you get to make some more logs and firewood in the near future...🤣 Can't wait to see the crane on the INSIDE of the shop being setup!

@Jay.Kellett

6 ай бұрын

Yeah, he needs to get someone cutting planks from all those trees to make garages for all his equipment to keep them dry and out of rain and snow.

Congratulations Matt! This is probably your best purchase ever based on the price/value. Having been around cranes most of my working career, please be careful as you have a very unforgiving piece of equipment as far a errors go. Pay close attention to your load chart and the condition of all your rigging. Have fun, just be careful. Really enjoy the channel, keep the videos coming!

Buddy of mine repaired a large crane. He took it for a road test and decided two blocks was enough. He said it had either a C7 or a 3216 (I can't remember) and in the cab was the largest bottle of Tylenol he had ever seen

I'm no crane operator (especially like you) lol, but i think i have an idea on how to extend that manual extension, extend one of the hydraulic extensions with the manual still where it is, hook the the line to something anything heavy enough, then pull the pin on the manual extension and retract the hydraulic extension, and that could be a way to extend the manual extension boom, awesome video by the way!

Matt, you should buy a conex at richy brothers, leave it there and set it up as an apartment/office and save travel time. 😂

Be careful with those old hoist cables, they can rot from the inside if the center section is made out of fiber. As Brian from the channel bcbloc02 learned when his overhead crane cable failed a couple of years ago. He is lucky to be alive and well. I think he had something like 22.000 lbs on the hook. A big Cincinnati radial drill that hit his newly poured and dried concrete shop floor, from about 3 feet high and broke everything.

@ligurian728

6 ай бұрын

I saw that and thought the cable was definitely due for replacement just from the video. When he dropped that drill I just turned him off and never went back. Very stupid and avoidable.

@GAIS414

6 ай бұрын

@@ligurian728 I wrote that one down as an accident. However he is a bit of a redneck engineer, at least he was transparent enough to leave it in the video. In his follow up video, he explained that he had inspected the cable from the outside and thought it looked fine. But when he inspected the cross section from the break he realized what had happened.

I was around, I was around when you had the church ! Why not build a dedicated bldg ? LOL, trying to figure out the jib. I had a 4 man crew waiting from 7AM until 5:30 PM for a crane to show up to put some elevator machinery in the penthouse of a 19 story apt bldg. . They showed up with a crane they had never operated before. He had to read the book to figure out how to get the jib in place. Took 2 more hours. 6 pics real quick and we left him /them there. Unbelievable waste of time. Bosses did not care !

I give that weak fuel pump credit for the low price. Great deal.❤😊😊😊

Load charts are really necessary. Load testing is really important as well. Different places I worked, crane accidents happened. Usually, it was because of underestimating the load or overestimating crane capacity. I've never tipped one over, but have been distantly involved in some of those. Most dangerous thing is booming down with a load that can't be grounded quickly. If you have to boom down with a load, or swing over the side, keep it very close to the ground. If it's up in the air, you'll lose the load and the crane.

Just need to make yourself some outrigger pads from 1" plate steel. You can make a jig to store them on the crane between the cabs and use the crane to set them and store them.

@tuju-

6 ай бұрын

It has those, Matt just put some sketsy wood under the outrigs

@The1nsane1

6 ай бұрын

Wood blocks are easier to manage.

@Bigdaddyslasher

6 ай бұрын

@@The1nsane1 yes but they rot

@Bigdaddyslasher

6 ай бұрын

@The1nsane1 we actually use both at work. Put the plates, then wooden ones on top of those.

@The1nsane1

6 ай бұрын

@@Bigdaddyslasher Depends how you look after them and what they are treated with. In Australia cranes of this size use wooden blocks.

metal winch line is actually considered a machine - since the individual strands are designed to move against each other. Some oil on the cable might be a good idea. Outrigger pads can be made just stacking and attaching several layers of plywood together.

I had the same Crane and it was a great money maker... Stop running the Crane in 2003 .. Worked at the WTC .. NYC , for months then retired and sold the crane ... Loved that Crane

be careful doing side lifts with this style crane you ideally do not want to lift with the boom swung past the forward outriggers its designed to lift from the back side. the front of the truck hanging off the ground acts as a counterweight. in crane trucks designed to be able to lift 360 degrees will have an outrigger in the front. I took some training to operate a similar grove crane to this but about 2 sizes smaller. also dump a bunch of oil on the drum for the rope to hold its rated weight it needs to be oiled

@JeffRiley-tc6cy

6 ай бұрын

yep… the ring gear that drives rotation sheds teeth like a mfer ive seen booms bent also

@JeffRiley-tc6cy

6 ай бұрын

the load charts will reveal zones that have reduced capacity i ran 39 ton altec …. no restrictions on those

I found your channel when you were building the container shop. It's been a fun ride. Don't stop now.

3500 bucks is a steal for this crane wow dt466 nice and a 453 Cherry bro nice find Matt 1:01 @Diesel Creek

Yep the wedge socket is manufactured that way so you can do it , wedge had extension through which clip can be secured. Or if you have a piggyback clip and no extension in wedge it fastens tightly to dead end but slides freely to live side. And another method that's hard to explain without a diagram 😅. You can take that to the bank . I like how I saw a rats nest on that main line and then it was gone when you were reeving lol

Stolen would be the understatement of the decade!! That will pay for itself about the 5th time you use it.

That's a great tool to have when you want to move something big and heavy without the need to fire it up Matt. I still can't believe you picked it up for $3500!! Hopefully it should make light work of raising the roof on the container workshop and the house build roof when you eventually get the time to get the build under way. First job for me would be sorting out the slew brake the last thing you want is to get a gust of wind shifting something and causing an issue.

Greetings: Don't forget to de-rust and oil both main and aux cables. I think the aux cable can help minimize rotation of lifted objects as long as there is a synchronizing control to account for the block & tackle multiplier.

If you are wondering how to extend the last section of boom. From fully retracted, extend it out two sections, lower the end to ground, push boom up or dn to try to pull pin. Next, with the pin out and the end of the boom on the ground, retract one of the sections till you reach the end, where you will see the pin hole insert pin. Now you lift boom up, and you will have full extensions. Good luck with that it is a two person job to extend extra extension.😮😊❤ if extension hasnt been pulled out it might need some help by fasting a cable to something so you can retract boom and hold jib so it doesn't go back with retracting. Watch pulling to hard if it has damaged stop. It might come completely out .. then you will have a job putting it back in.

Yes, 35mph does feel like Mach1. You should drive one with a full rotary drill rig mounted on the chassis!

@philipcable437

6 ай бұрын

Brings back memories of my drilling days

@IowaSVT

6 ай бұрын

Flat towing the support truck behind it