This toilet is garbage. Our apartments just replaced them and everyone is complaining. They don't freaking flush anything completely, and it just bounces back into the bowl. Flush again. Nope. Flush again.. maybe. Give me back my "water hogging " toilet back.

@esd251

5 жыл бұрын

Alisha D yep. They did to our apartment too yesterday and I’m hating it already a minute after they installed it!

@JM-yx1lm

5 жыл бұрын

Keep on complaining and the government is going to force you to use a composting toilet.

@jessicazoubek9678

3 жыл бұрын

I got this going on too this thing SUCKS

@dawnrigler2381

Жыл бұрын

That's my EXACT scenario. Our building did renovations last winter. It took a year, but this damned thing won't flush. I've plunged, poured buckets of water in both the bowl and the tank. I've checked all the valves, etc. This thing is the worst!

@dizydank

7 ай бұрын

I work maintenance at an apartment complex that switched to these toilets also and ever since then we have more calls than ever on plumbing issues. Stopped up toilets and house floods. They just don't produce enough water for 40 year old cast iron pipes.. the easiest thing we found to do is buy a Milwaukee Air Snake. It works about 90% of the time and you don't have to pull the toilet and snake it. Saves you a lot of time and hassle.

They installed these toilets in all our apartments 2 years ago, only difference being they installed the one with the flush lever outside instead of the one with the button in the middle. However, now nearly after 2 years, our toilet suddenly started flushing very slowly. I thought it was a little clogged but no clog, I always had to hold the lever down for a few seconds to get a complete flush. It was very annoying. All the water holes inside the toilet bowl were still very clean and the water was still flowing into the bowl smoothly but was getting no smooth/fast flush as the day it was installed. I even tried cleaning the small syphon hole inside the bowl but it seemed so clean. I took the toilet tank apart (took off the center stopper and the lever that is connected to it, then I unclipped the plastic housing and took out both those pieces. Then I see the air vent they mention in this video but don't show us. The air vent is covered with a green plastic piece with a hole in the middle and has a small ball of foam inside the tube. With a flat head you can remove the green plastic piece by prying it out. Try to remove the ball of foam in the tube as well. When I flushed the toilet without the green piece the ball of foam shot out of the tube so it was easy and I didn't have to actually unplug my water toilet water hose and the screws to remove the tanker to get in there and clean the vent, although it would probably be easier to clean your air vent by completely removing the tanker from the toilet. Then I used a manual pump I have with two hoses/tubes and inserted one hose/tube in and the other I put in the tank with water. I started pumping water down the air vent to really get a good clean. Then I reversed the tubes/hoses and was doing an air suction to make sure the air vent was clean, and I was hearing the toilet react with a flushing sound each time I did a suction with my pump. Lastly, I just put the foam ball into the green piece and inserted the green piece with the foam ball back into tube and clipped back the black plastic housing. After putting everything back together in the tanker, it flushed super fast like it did day 1!

@zeekflash6924

Жыл бұрын

Wish , there was a picture or video or what your describing , low flush ,& I tried clean clr, and it’s not clogged just have to press and hold down til it flushes .. kinda annoying cuz , it goes down slow

@DaveRaveVideo

4 ай бұрын

Thanks for the instructions! In case it helps anyone else... After 8 years of daily use by my family of four, my Niagra Stealth (model #N7714) suddenly started flushing very weakly. Thanks to your instructions, I (1) turned off the water to the toilet, (2) removed the push-button lid, (3) flushed the toilet almost dry, (4) disconnected the water supply, (5) removed the two wing-nuts holding the tank to the bowl, (6) removed the tank and set it upside down in my shower to dump out the remaining water, (7) removed and cleaned the rubber gasket, (8) for the TANK I used a flat-head screw-driver to scrape the crap out the (smaller stubbed-hole) air vent, and then flushed it with water from both the vent-hole and the tank's top-side, (9) for the BOWL, I used a flat-head screwdriver, bottle-brushes, and thick wire to clean the crap out of the (smaller-hole) air-vent on the bowl, and then flushed it with a few quarts of water (10) reassembled and tested it. Success! Unlike your instructions, there was no foam ball or hose to clean. The bowl's vent-hole is just a hole in the porcelain bowl. The tank's vent-hole is just a plastic stub. When I flushed the BOWL's vent hole by pouring a few quarts of water into it, I could see the crap going down into the water in the bowl (apparently through a vent hole above the P-trap which can't be seen). The water flowed freely from the bowl's vent-hole into the bowl, so I felt confident that the bowl's vent-hole was clear. Similarly, when I poured water into the TANK's plastic-stub vent-hole, crap-particles came out of the tank and into the shower. Yuck. I flushed the tank's vent-hole and rinsed the tank until it was clear. The job was much easier than I expected. FYI: We got two 0.8 gpf Niagra toilets for free from my water company (here in Silicon Valley where water conservation is critical). I previously had top-rated 1.6 gpf Toto toilets. I was skeptical about the Niagra toilets, so I stored the Toto's on the side of my house for about 4 months, just in case the Niagras didn't get the job done, but they did get the job done, so I gave the Toto's to a friend. We have had far, far fewer clogs with these Niagra toilets than with any toilet I've ever owned-- even our old 2.5 gpf toilets that the Toto's replaced. My other Niagra toilet is in the master bathroom so it gets less use and hasn't had a problem yet. But if I just have to clean the vent-holes once every 8 years, I'm OK with that.

@stzez

4 ай бұрын

Junk doesn’t flush, why can’t they make a toilet that is simple and works.

I bought my stealth flush from Home Depot several years ago. When it wouldn't stop running I called Niagra and talked to a real person who helped diagnose my problem and mailed me the suspected replacement part with instructions. I think it is fixed.

toilet works great and I recommend it. I have two and will replace all with it. But after two years I had, rather suddenly, slow flushing. after watching this presentation and others, it seemed to me that the air vent was clogged. I removed the water closet from the base and, sure enough, the vent hole and some of the air tank in the water closet was filled with black, odorless crud. Probably the result of our non chlorinated well water. It shows up in other water appliances too but seems to be non toxic. In any case, cleaning the vent and the air reservoir solved the problem. I used a wet/dry shop vac and then flushed top and bottom with water.

@hopesmith8007

6 жыл бұрын

I just bought this model and had it installed. However, the flush is weak and sluggish. Even toilet paper doesn't get flushed. Requires two flushes. When I press the flush button, water never flushes all down. Just the water at the bottom goes down - never all the water as I've see on the demo send other videos on you tube. Water is at water level. Any advise on how to fix the weak flush?

@XxDonPerryonxX

3 жыл бұрын

@@hopesmith8007 did you figure this out?

@JoseGomez-oz5ec

2 жыл бұрын

Yup, mine did the same thing after 2 years. Suddenly, getting a very slow flush and I had to hold down the lever to get a complete flush (mine doesn't have the button in the middle but still same stuff inside the tanker). And it was not clogged. It turns out, as you stated, the toilet's air vent. After taking apart my toilet and cleaning my air vent it flushes fast again like it did day one. I pryed out the plastic piece at the top of the air vent, removed my foam ball and did a deep cleaning inside the tube by using my manual pump with pressured water down the vent and then doing suction to make sure it was good. Put everything back together and it flushes fast again. Thanks for mentioning that it was the air tube because in my case it was... and it wasn't a partial clog as I initially thought it might have been.

@paulv1948

Жыл бұрын

@@jeffreyspoelstra2427 you have to remove the water closet...the part that holds the water and flush apparatus. (turn off your water!) in the lower section (the part with the bowl), you will see a hole about 1" in diameter that goes down into the bowl and has a mate on the upper section (water closet). I think it's towards the right side as you stand in front of the toilet, and at the back. This passage allows for the quick movement of air that is necessary for the quick flush action. This hole is not visible from anywhere else. let me know if it works for you.

And if you're still getting a weak flush after trying all of these, take the lid off the tank and unclip the latch on the left side of the black plastic piece that surrounds the flush valve, exposing the top of the air transfer tube (directly behind the flush valve). Inside the top of the tube is a red plastic insert with a small hole in the center. Slide a wire into the hole as far as it will go. Then slowly pull out the wire, wiping fecal matter off the side with a large wad of toilet paper. (Like checking the oil on your car only more disgusting.) Next, slowly pour 2 cups of boiling water into the hole. If it doesn't go down quickly, you may have to "snake" the tube again and repeat. Replace the black plastic surround and secure it with the clip. Now flush the toilet a couple of times. With luck, it will have a much more forceful flush. So what happened? If you try to remove a clog in one of these toilets by plunging it, some of the matter can get forced up into the air transfer tube. If the air transfer tube is blocked, the toilet cannot use air pressure to assist in powering the flush, as it was designed to do. On the other hand, because of the twists in the discharge path between the toilet bowl and the hole in the floor, these aren't the easiest toilets to snake.

@stevehayward2890

3 жыл бұрын

I’m not sure what you mean by “the black plastic piece that surrounds the flush valve.” I don’t see a latch on the left side of anything. Maybe a photo of this latch would help.

@JoseGomez-oz5ec

2 жыл бұрын

Yup, that was my problem. After 2 years, mine started flushing very slowly. I had to hold the lever (mine has an outside lever not a button in the middle) for a few seconds to get a complete flush that took awhile. My plastic piece inside though was green and there was a foam ball inside the vent tube

@JoseGomez-oz5ec

2 жыл бұрын

@@stevehayward2890 there's a big latch/clip towards bottom left of the plastic housing that surrounds the water stopper. You unlatch it and that big black plastic housing will come out.

@callofcurthulhu4622

Жыл бұрын

This solved my issue… didn’t note any blockage or “matter”, but seemed to help the flushing after running a thick wire down the tube and out into the bowl

Is there any way I can order a silicon gasket of the flush valve to stop the running water?

Niagara Stealth toilet leaking and won’t stop? Answer: (1) Turn water off and drain bowl. (2) Unscrew the raggedy piece of trash at the base. (3) Remove and set at the curb for next trash pickup day. (4) Replace with a Glacier Bay toilet. (5) Get a quiet night’s rest

Excellent video. My toilet kept running, turns out all it needed was cleaning the rubber seal disc.

Thanks very detailed troubleshooting guide.

I've had 3 Stealth toilets for over 5 years. Love them. Never had a problem or need to double flush! The added height is great for my knees. Wouldn't own any other toilet.

@bobfmirvine6652

2 жыл бұрын

I agree wholeheartedly, same experience, 3 toilets had them longer than I can remember.

@zeekflash6924

Жыл бұрын

Wait , til it flushes slowly or hardly flushes .. after 4 yrs , it basically don’t work and customer service is no help .. they don’t show u how to , clear air transfer tube .. ugh

@crabapple6775

2 ай бұрын

do you mean you had 3 different stealth toilets in the same location over 5 yrs? and I don't mean the same house, I mean the same spot in the same house ? If so, I think that's insane. we had the same toilet in the same spot for 40 yrs with maybe 1 problem, until the lat 2 yrs or so. Then with all the modern improvements, we have probably had several toilets in maybe 6 yrs.

If you're here because you need to adjust / fix your toilet be mindful that similar models come apart differently. I have a single flush stealth and to access the fill valve its released turning counter clockwise and per the instructions not to remove the pin holding the float valve. Your water level indicator is not always on the black plastic part as well. Like anything else that is new its not designed to last, have replacement parts readily available buy them before you need them. Keep your instruction manual you'll need it.

Thanks! My super efficient toilet which is so efficient it can barely flush a bowl movement has apparently been running nonstop for months, costing me probably a hundred bucks! This video helped me stop the bleeding!

Thank you very much. After watching your video I was able to remove and repair the gasket and it stopped the leak. I figure you saved me anywhere from $65 to $95 by having a plumber come fix it.

@warrenb2856

23 күн бұрын

$95 for a plumber, you do not live in California do you?

I lifted the float cup Manually and the water stopped, so it’s not the rubber disk. I lifted it up again and see if the water in the toilet stopped running as well and it did, and I don’t think the water in the toilet was draining either, so I don’t think it’s the seal on the flush valve either:/ it won’t stop running. P.s. the fill valve where the rubber disk is, is leaking a little with the cap on. I little droplets on water flowing down to the float cup. It still have a low water level.

I have the N7714 model. It is flushing great but it’s not pumping water back in the tank, please help! Thanks much!

HELLPPPPP!!! When my toilet finishes flushing, water seems to escape through the siphon jet. Not too much, but enough to leave the bowl with noticeably less water. Every time! How is this fixed?? Please help!!!

Model 4417 , I think : Low or not flush fix , detach tank from bowl , there’s a small hole on bowl part . Pour hot water down hole , it should Not over flow or come back up . If water comes back up , there’s a clogg , the small hole is part of the flush mechanism .. I pour hot water and or use a high pressure water hose , there will be a piece of clogged debris , that will be in tank bowl , that’s how I knew this was the problem. Not sure why niagra would design , the toilet this way , it’s basically disaster eating to happen .. I guess I’ll have to unclog this hole every couple of yrs .. cuz , toilet worked fine for 4yrs and then , after process of elimination.. I discovered this clog .. hope niagra will, design future toilets better

I bought one of these a few years ago and loved it, so I bought another one for the guest bathroom. I installed it last night and the flush was ridiculously weak compared to my other one, so I searched and found this video. Never in a million years would I have guessed that the problem was that the toilet tank was leaning against the wall so that the air tube wasn't working properly, like the video mentions at 2:50. I've since adjusted it just a tiny bit forward, and it's fixed! Now I have two efficient, powerful toilets in my house!

@DougSitze

2 жыл бұрын

JB! how tiny is tiny? I tried this as well and I think it made some difference, but it's still not where it should be. Wondering how much wiggle room exists here before it's not aligned properly.. thanks!

@jonathanbellows3403

2 жыл бұрын

@@DougSitze In my case, I just slid it forward far enough so that I could slide a piece of paper between the back of the toilet tank and the wall; just enough to ensure there was no lean. That was it.

Great video. I swapped out my fill valve after following the debugging steps here. The toilet no longer just runs. $12 fix!

@danielbermudez7747

13 күн бұрын

Where did u buy it from I seen all of them have over fill hose but these dont

I have removed my toilet and replaced still clogged I have snaked it from top and bottom is the snake head supposed to go all the way thru and come out the other end?

This is the second one for the basement bat. kzread.infoUgkxOuLt8IL_GxhhaK8DBuKEL-zV0UJVpWZn , works great

OM! 🎉 it worked by us just rinsing the black rubber valve.

the letters WL stand about 5/16 tall, I am guessing. there is no horizontal line by those letters. I guess I can just guess if the water should be at the top or bottom of those letters, and also what is the tolerance above or below. as with most produc designers, it seems their motto is : better to let millions of people wonder than to easily make such info clear. A protruding line would be so helpful, and colored white even better.

Just installed. Takes 5 (FIVE!) flushes to flush toilet paper. Really disappointed with this product so far. Hoping to find better troubleshooting that may make me not so disappointed.

@fredhamilton1701

2 жыл бұрын

Did you ever get it working/fixed? I had 3 of these toilets for 7 years and they were incredibly reliable.

Thanks! the screw on lid just needed to be adjusted.

Caught the 800# in Your Vid, Thx... The Float Making a Squeal Because of that Little Black Seal, They're Sending a New One Under Warranty!

four year old Stealth UHET; The flush valve silicon rubber ring developed two blisters, causing constant drainage. I punctured the blisters just on one side. They were filled with water. Squeezed the water out, reinstalled and tested ok. Did this because it takes seven days for the replacement parts to arrive. Conclusion: Bad quality material and bad parts availability at exorbitant price.

‪N7714 toilet fill valve gasket replaced and hissing noise stopped. However the gasket seems too small as now it just keeps over filling tank. Even after I left of the arm on the fill valve water keeps flowing! the old gasket that makes a hissing noise but will stop fill valve‬

My Stealth is a Glacier Bay Power Flush from Home Depot. It's not a top flush like this model. It still flushes very strongly, but the level of water in the bowl doesn't refill to sufficient levels. I've got plenty of water in the tank for each new flush, and I can make the bowl refill higher if I hold down the flush handle, but I don't want nor should have to have to do that. I've been in contact with support online and over the phone, and all I got today in the mail was what appears to be a silicone seal for the bottom of a flush mechanism that may or may not resemble mine. Has anyone with the Glacier Bay from at least two years ago with the flush handle on the outside experienced this problem with low levels in the toilet bowl after flushing?

@for5155

Ай бұрын

Yeah. How'd you fix it.

I just installed the Niagara Stealth 0.8 GPF UHET. The flush is weak and sometimes takes two flushes. Water doesn't flush all the way down. Tank water level is correct. Any suggestions?

@NiagaraCnsvtionCorp

6 жыл бұрын

Hi Hope, We're sorry to hear you're having trouble! If you want to contact our customer service manager at your convenience, he can try to troubleshoot with you over the phone. Troy Bleck 800-831-8383 x1180

Where do you get that special fluidmaster 400a

@NiagaraCnsvtionCorp

4 жыл бұрын

Hi there! You can reach out to our customer service at info@niagaracorp.com for any information regarding our parts!

When I plunge my toilet water comes from the tank in the back why

This is a great video, and I don't even own one of your toilets. The bits about snaking and troubleshooting vent problems are applicable to all toilets, really.

@NiagaraCnsvtionCorp

2 жыл бұрын

Thanks Kirstin!

Fill valve cap at 1:40 is very hard to remove and put back. I can not put it back in.

The silicone seal has an indent or raised circle around the inside. Does that face up towards the valve or down towards the toilet hole?

@NiagaraCnsvtionCorp

2 жыл бұрын

Hello! Sorry for the delay in responding. The seal should face down towards the trapway - the toilet hole. Hope this helps!

Before ordering a gasket check to see if the plastic hold down bolt for the tank top button came lose. Mine did and fell bete\ween the stopper and drain, preventing tank from filling. Fished out plastic bolt, reinstalled it and now it's fixed.

@taskforcekillah9722

3 жыл бұрын

Thanks man you're a life saver i been freaking out because I accidently flushed a few wipes. They came back someway then the toilet stopped flushing come to find out it was the white ring piece to the flush button seriously thanks

Awesome video. I can fix it myself.

I like this product simply because it self plunges, meaning all we have to do when it gets clogged is flush it again. However, we've had it a month, and the back part of the tank where the two pieces connect just started leaking. It's frustrating.

My toilet (N7714 Stealth) began a very slow leak around the fill valve. I tried using a replacement washer which did not stop the leak. I looked inside of the tank top it says use a "Fluidmaster 400A" as a replacement. I bought a 400A at the local hardware store and installed it. That was when I discovered it was not exactly like the one I took off. The original has no fill tube and the new one did. I attached the rubber tube and stuffed it inside - seems to work. However when I called the Niagra help line to verify work, I was told that I had to buy replacement parts from only 2 places - by mail order. Never read that anywhere in these help videos. Anyway, a very unsatisfactory call and a really crappy response from Niagara. I really like the toilet, but having to buy parts mail order is really bad - no weekend fixes here for sure. I still have no idea if my repair is good or not.

@boblanglois9185

2 жыл бұрын

a400 you used is fine - stuffing the rubber tube inside as you describe will work fine. I replaced approx 80 A400 Fill Valves in this same toilet last week. No issues. A400 works just fine and can be purchased just about anywhere

We just installed one of these and the base of the toilet (not the tank or bowl) makes a gurgling noise after a flush. Is this a problem? We don't see any bubbles but can definitely hear a loud gurgling noise coming from the base of the toilet.

@curtisbme

5 жыл бұрын

Yeah, that isn't a good thing if it is indeed coming from the floor area vs just seeming too. It might indicate that you don't have seal with the drain and you are hearing noises from the sewer line. If only used the one wax ring it came with it could be that it wasn't enough, as is often the case with thicker tile floors. If it doesn't have a tight seal you could have water leaking from the flush and sewer gas/stench leaking out. You'd want to pull it up and check and possible redo it. Personally I don't recommend anyone use wax as I found the Fernco waxless seal to be a much better solution as I don't have to worry whether I used too little, or if the wax made a full seal or when I might need to replace it.

Details of my issue: Problem: Toilet wouldn't fill and water would not stop. Cause of problem: Plastic nut that holds flush button onto toilet lid came off and held flush valve open causing the tank to never fill. Solution: Unscrew flush valve to remove flush button nut obstruction. Video at ~2:10 explains how to remove flush valve. Place flush valve back on, tighten nut to flush button back on lid firmly. I hope this helps anyone else!

@AT-sb8wq

5 жыл бұрын

I know this comment is old, but thank you sooo much. This was exactly my problem. It was driving me crazy.

@LauraxForever

4 жыл бұрын

omg thank you so much, i saw the plastic nut on the side once i lifted the flush valve, problem solved instantly once back on!!

How do you take off the black cap?...shizz.. there's no way that cap came off that easy... and never explained how to without breaking it...

How do you increase the amount of water in the toilet bowl

@lavenderwarrior1

2 жыл бұрын

that's what I want to know

Thank you. Much better without spending lots of$

install a toilet of this system but when flush the water does not go it stays like it was clog but the tank did not have sufficient pretion call customer service nobody answers

My black button keeps getting stuck down not raising back up .How to fix that.

@NiagaraCnsvtionCorp

Жыл бұрын

Hi Rob! Thanks for your question - please reach out to our customer service team! They're going to be able to help you figure out how to fix the button. You can call them or email them: info@niagarcorp.com | 888-733-0197

@mrgriffey6026

Жыл бұрын

N7714 toilet fill valve gasket replaced ​@@NiagaraCnsvtionCorp

Horrible toilet my apartment has one. Its never flushed correctly then right before Thanksgiving it leaked and we had a plumber come out who ended up having to cut into our wall to unclog the piping its now two weeks before Christmas and its clogged again but worse it wont flush any water.i basically have a toilet for decoration

@NiagaraCnsvtionCorp

Жыл бұрын

Hi Bethany - we're so sorry to head that you've had a bad experience. Please reach out to our customer service team and let us see if we can rectify your situation. You can reach them by phone or email at info@niagaracorp.com or 888.733.0197

N7714 toilet fill valve gasket replaced and hissing noise stopped. However the gasket seems too small as now it just keeps over filling tank. Even after I manually lift up the fill valve arm on the water keeps flowing! the old gasket that makes a hissing noise but will stop fill valve‬! “A BIT BLUE A BIT WHITE A BIT

@NiagaraCnsvtionCorp

Жыл бұрын

Hi there! Please reach out to our customer service team - they can help you identify and solve this issue! You can email them at info@niagaracorp.com

OMG, I can't find the parts I need. HELP please!!

where to get replacement parts? I need a new seal as shown at 2:24 of this video.

@crystalyang255

3 жыл бұрын

You can call the number you see on the video. It is on the bottom of the top cover. parts are free.

@melaniekuehn3813

2 жыл бұрын

same here would like to know part number so i can get from home depot or lowes ASAP

If it's not the silicone seal - what other issue could be causing the tank to lose water?

@NiagaraCnsvtionCorp

Жыл бұрын

Hi John - please send your question to our amazing customer service team at info@niagaracorp.com and they can help you trouble shoot what's going on with your Niagara toilet!

Bought it new, toilet doesn’t flush just fills and drains itself I have no idea why this isn’t working

Yeah no on the last part snaked the vent and all three clean outs still gurgling happens and doesn’t flush tomorrow in the morning I’m breaking the lower half

slow leak - not sure if it's the seal or the entire valve (what part #'s - should I order)?

@NiagaraCnsvtionCorp

Жыл бұрын

Hi John! Please reach out to our customer service team with the model of your toilet so that they can assist you with identifying and ordering the part you need - info@niagaracorp.com

DONT BUY THESE TOILETS I work maintenance at an apartment complex that switched to these toilets also and ever since then we have more calls than ever on plumbing issues. Stopped up toilets and house floods. They just don't produce enough water for 40 year old cast iron pipes.. the easiest thing we found to do is buy a Milwaukee Air Snake. It works about 90% of the time and you don't have to pull the toilet and snake it. Saves you a lot of time and hassle.

This video was very helpful. My toilet has been here about 7 years and has begun making a "vacuum" sound as it flushes. I think it's flushing just as rapidly as it did before. I'm not seeing a sound like that being typical. I'll be climbing up on the roof tomorrow to see if there's anything blocking the vent but it's raining today. Anyone else had that sort of sucking/vacuum sound as it flushes? Thank you.

@naseausderhuette

Жыл бұрын

I have this, a high pitch hissing noise. Did you ever fix this?

i just bought a stealth flush at home depot installed it and filled it the water just keeps running after it fills it continues to just run. the toilet is brand new this should not be happening nor such i have to order any part or have build up because it is brand new. how can i fix this issue

@four_20hitman___97

3 жыл бұрын

Same issue

@four_20hitman___97

3 жыл бұрын

Brand new. After I flush water just keeps running into bowl and tank refills. My water bill is up $150

Efficiency at what cost? My American Standard was a nightmare, flushing on it's own thoughout the night. My Kohler is substandard, with a leaky valve at 4 years. I'm going back to a 3 gallon flush if I can find one.

Leaking down bolt when it’s flushed?

@remmyerickson4779

3 жыл бұрын

We have the same problem and can't figure out why the gasket is leaking

I turned off the water and then turned it back on and now it continuing running the water...help

@NiagaraCnsvtionCorp

6 жыл бұрын

Hi Penny, If you go to 0:28 in our video, it should help you fix the running water issue. If you are still having trouble, please give us a call and we can walk through some options over the phone.

What if the problem is, it won’t flush at all…..button won’t depress

NIAGRA N7714 air transfer tube is clogged and also the replacement

How do I increase water in bowl? I have to plunge for every wad of toilet paper. That’s means 3 plunges per visit. Nothing will flush without plunging. How do I get a more powerful flush. I moved from a 1920s building with powerful flushing to a 2005 building with these Niagara Stealth single flush toilets that are my daily nightmare. I plunge and plunge and plunge. I need more water. There is only 2 cups of water in bowl every time I visit and open lid!

@NiagaraCnsvtionCorp

Жыл бұрын

Hello! Please reach out to our customer service team at info@niagaracorp.com and they can help you identify the issue you're having and help you fix it!

While not as shockingly wrong as the instructions that the HD model comes with, this is incomplete and out of date. Trying to determine where the water line should be from the instructions makes you think someone wrote it who has never seen the toilet, has never written or read instructions in their life, and didn't allow anyone to proof read it. Not only do the instructions claim notably incorrect things like that that the gasket between the tank and bowl and the flush button is already installed in place from the factory, it has tells you to look at instructions that aren't even there. For the water level, it has a section under Troubleshooting 'poor or sluggish flush' that the WL might be to low and you should adjust it to the Water Level Mark which it doesn't say where that is and refers you to "Step 9". The instructions stop at Step 8... Here the instructions for WL show a mark inside the center tube which is not where (I think) it is now which is on a step on back left of the center chamber outer ring. Would have been a lot easier to simply state something like "The water level should reach to just below the top of the center chamber's outer ring. If it goes over the top of the ring adjust the Fluidmaster valve screw lower.". The instructions in this video are problematic as it seems to be randomly addressing things so you don't know what is in the video and then it talks about things without showing them. From "lengthening the snake" to addressing blocked vent pipes. The vent pipes are likely to be even more confusing for people because this video keeps showing images of the toilet, possible making folks who aren't knowledgeable about their plumbing thing this toilet has some sort of vent that needs to be cleaned. Regarding the vent pipes, it is absurd to talk about troubleshooting and resolving significant issues with your plumbing like that here. Simply mentioning some possible larger issues, how to tell if it might be them (like your sink draining slowly or gurgling), and recommending getting plumber to check it is what you should be doing. Seriously, telling general consumers to go on their roof and run hose down the air vents when talking about troubleshooting their toilet??

tl;dr - replace with old school toilet and go have a cookie.

I fucking hate this toilet. If I have to unclog it one more time imma lose it.

It cannot be plunged because there is air valve connected to the drain. That's a pretty a bad design.

My N7714 does not have enough water pressure to flush properly anymore. I did every "test" in this video and nothing helped. I hired someone to look at my vents on top of the roof and they are clear. I had TWO different plumbers look at my toilet and they both said REPLACE IT with an old-fashioned toilet. They said many cities sewer systems are not compatible with these low-water flush systems. Please post ANOTHER VIDEO that shows me how to fix the low water pressure problem with my toilet.

@maryamghorbani260

3 жыл бұрын

In any case, cleaning the vent and the air reservoir solved the problem.

@JoseGomez-oz5ec

2 жыл бұрын

If you mean that you were getting a slow flush then the way I fixed mine was by taking the tanker apart and cleaning the air vent inside the tanker/toilet. Unfortunately with this modern design, the air vents that supply the high/fast flush pressure can get a little clogged resulting in a very slow/low pressurized flush. This happened to me after around 2 years of having this toilet. I cleaned my toilet's air vents and it flushes fast again. Once you unlatch the black plastic housing inside your tanker, you'll see a tube with a green plastic piece and a hole in the middle and there should be a foam ball in there (at least there was one inside of mine). I pryed my green plastic piece out with a flat head and removed the ball and proceeded to cleaning the air tube as best as possible. Then I put everything back together and my toilet flushes very fast again.

These "toilets" are just floor decorations that replace vintage toilets

He didn’t say anything If the toilet doesn’t flush it just fills with water

I don't care for these toilets as I have very large bowel movements and so I prefer flushes that use very large volumes of water.

These toilets are a piece of crap#...The water just stays and everything else!

Don’t ever buy one of these, they can’t even flush liquids, made a huge mistake installing one for my dad

I hate this crap. It’s not enough water to wash the shit out of the bowel 🙄

@2006marsha

Жыл бұрын

Can I take the stealth out? And put in a regular flusher

None of this information helped -_-

@NiagaraCnsvtionCorp

9 ай бұрын

Hi Daniel - sorry to hear that! Please reach out to our team at info@niagaracorp.com and our customer service team might be able to help you further!