I'm pretty sure RocketWerkz have daily odds on "What's Mick gonna do to screw up our best laid plans with Stationeers today?"

@cowsareevil7514

Ай бұрын

I think that is exactly the creative freedom they are aiming for. However, the freedom to be stupid is a personal choice.

No such thing as a too-long play through. Keep the episodes coming!

Oh my gosh, I lost over the fire extender

Luna’s bulging eyes means she is serious about her mission. What a good kitty.

@cowsareevil7514

Ай бұрын

Or the pressure in her suit is too low.

To be fair, Stationeers isn’t the only game that lets you put welding fuel in a “space” suit

You can use a silo to make fast decay food, just put food inside and when you pull the open lever the food will be decayed instant.

@pvstiphout

Ай бұрын

Good to know. Thanks Argon

@cowsareevil7514

Ай бұрын

I though thay had fixed that so I didnt even try

@argonxenon6839

Ай бұрын

@@cowsareevil7514 I wanted to use a silo as a food deposit recently and I lost a bread loaf like that lol. Now I use the silo as my fast source of decayed food for the compostor.

I had terrible flashbacks of trying to use a digital flip-flop as a compact sorter. Hours and hours of things randomly coming out of the wrong holes before I finally gave up.

@cowsareevil7514

Ай бұрын

Same for me. Although the new sorter might be an improvement.

Idea for the liquid CO2 bit: The liquid is likely freezing because there is nothing to add extra energy to it to prevent the freezing (so as the gas part expands and leaks out, it's taking the energy with it making the remaining liquid colder). instead of using a liquid drain to add it to the room (where you're getting the freezing issues), have it get added to a section of pipe that is always flushed with air to prevent the freezing (so same style coding you had to do with your poo-water boiler for flushing it with warmer air, but swap the evaporator with a pump of some sort)

@cowsareevil7514

Ай бұрын

The freezing was because the pump was too fast. By slowing it down, the room air was enough to heat it and stop the freezing.

Cheeky little time skip there at 7:06, next time don't have the clock in frame. lol Still made me laugh though. ;D

@cowsareevil7514

Ай бұрын

LOL, I cant get away with anything. I tried so to keep the angle of travel that I didnt even see the clock.

Fairly sure the liquid inlet keep exploding because there is no liquid volume between the inlet and the liquid volume pump and the CO2 needs to boil off to be released as gas. So when it surges to dump CO2 in the room after the pollutant is out of the tank, there is no room for the surge, so it pops the inlet. A pipe between the liquid volume pump and liquid inlet should solve the issue, but if you want to be a little extra careful, pop a pipe radiator on that single piece of pipe to boil the CO2 off faster, causing the inlet to expel it faster. Pretty sure the liquid inlet exploding counts as an explosion, so I'm sorry, but the button needs to be pressed or I'll have to report this to the higher ups.

@jezm-l3941

Ай бұрын

Could the vent next to the gas sensor be sucking out the gas and therefore the sensor measures less CO2 making the pump let in more and then popping the drain?

@cowsareevil7514

Ай бұрын

Noooo. The counter was going so well. Don't report me or I'll have to fill out hundreds of forms.

With pumping the liquid CO2 in to your green house, try using a portable tank and connector as an evaporator, as it does not let liquid out the gas connector. 😀

Mick - another enjoyable episode and thank you for doing these sir. Also minor question. With the new phase change system is it possible to use it to get gas is hot enough to use in your furnace?

@cowsareevil7514

Ай бұрын

Water has the highest temp for phase change at about 350C so yes but for solder and not much else.

@stormfire962imastarcitizen5

Ай бұрын

@@cowsareevil7514 Thank you for the reply back and this information.

I’d love to see a build of the liquid nitrous collector. I’ve been struggling for ages to crush nitrice and collect the nitrous but inevitably I get frozen pipes and loss of containment ensues.

@cowsareevil7514

Ай бұрын

Pre-pressurise the NOS tank to 3MPa with nitrogen.

That liquid inlet vent dont work too output liquid dont they!? Try and burts a small length of liquid pipe like you did once. you made a improvised passive vent with the gas pipe.

Can’t you just make the furnace box a vacuum rather than pressurising it?

@chevbob

Ай бұрын

furnaces radiate hard into vacuum, whereas they'll convect into an atmosphere until temps equalise and then stop losing heat. Same radiating heat loss happens when you try and weld a furnace into a block. All the old cheeses: gone. Gone........ ;-;