▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ T H A N K Y O U F O R W A T C H I N G ! P L E A S E L I K E A N D S U B S C R I B E ! ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬

Thanks for Ultimate DIY great review and soldering testing.😘🎉

@UltimateDIY

3 жыл бұрын

Thank you for sending me the soldering iron. It's perfect for my use.

@SequreTech

3 жыл бұрын

@@UltimateDIY Glad to here that.Thanks.

I've seen people with OCD shearing bolts in engines and clutches, hitches wheels after being told it's fine stop tightening!!!! OCD is dangerous.

@UltimateDIY

2 жыл бұрын

Yes, I know 😄 I do my best to let logic win.

Hi, will it work with a PD aware power brick? I have one that goes to 20v@2.5amp.

@UltimateDIY

2 жыл бұрын

Hi. Good question. I don't know the answer, as I don't have any PD supplies.

is it possible to fit T12 tips ? seems to be the same diameter

@UltimateDIY

3 жыл бұрын

I do not know, but they seem similar.

Happy new year 2021😘😘

@UltimateDIY

3 жыл бұрын

Happy new year! 🎉

Nice tips compared to the hatchet tip normaly comming with these soldering irons.

@UltimateDIY

2 жыл бұрын

Yes, indeed 👍🏻

Haha I got the same from Banggood. Unfortunately mine is not ok so I returned it. I didn't like the strange barrel Jack Connector which is not standard, I had to cobble an adapter from some wires to XT60. Also not working from 5V USB C, you need PD. Also the Standby Temperature is not settable, you can still burn yourself at 100 Deg C.

@UltimateDIY

3 жыл бұрын

The only downside to mine is that it does not work from standard phone chargers. But that makes sense. To get 60W from 5V you would need 12A. I will make my own power brick from an old 20V laptop charger and a modern USB type C cable.

@szaas1jjsjjsklk666

3 жыл бұрын

SQ-D60B is equipped with a PD protocol adapter cable. The PD protocol is set on the power cord so that the model aircraft battery can also be used.

@szaas1jjsjjsklk666

3 жыл бұрын

Happy new year 2021😘😘

@bbogdanmircea

3 жыл бұрын

@@UltimateDIY Yes but the barrel mother connector to USB C is really strange, it has a ticker middle pin which is not standard. I also have a brick that gives 20 V and 11 A but I couldn't connect it to the Jack, so I made an adapter to the XT60. They should have really used a standard Barrel. Also you should have measured the current to see the real Power it draws.

@UltimateDIY

3 жыл бұрын

I think this barrel connector is more standard in laptop chargers. Mine fitted perfectly, but as you say, it's quite thick.

A got electrict current about 10-11 volt in bolt of this solder (all of three bolt show this current, not only the tip). Is it normal or there is something with mine?

@UltimateDIY

Жыл бұрын

Not sure what you are asking, or between what you are measuring that voltage?

@erniarrow

Жыл бұрын

Sorry my statement is unclear. I accidentally got shocked when my finger touched the bolt on the soldering iron body. So, I checked the voltage between the bolt and ground using a multimeter and measured a reading of 10-11 volts. Is it normal? I am already using it about 4 mounth.

@UltimateDIY

Жыл бұрын

I suspect there is a problem with the power supply that you are using.

@erniarrow

Жыл бұрын

I have the same suspicion. Currently, I am using a non-official AC adapter with an output of 19 volts and 3.42 amperes. Perhaps I will try replacing it with a power source from a LiPo battery and see if the issue can be resolved.

@UltimateDIY

Жыл бұрын

Check for a voltage between the negative of your source and ground. I suspect you will find the same 10 to 11V.