Thanks BD. You saved what little bit of sanity I had left

@BDTennessee

3 жыл бұрын

Boss, glad video helped! Its little more doing than a Admiral. I try telling others there not exactly the same cause you can do a "Mix" on Admiral and this method for Lemon!

Incredible video

Thank you thank you thank you! Love your channel and slow exact information. Really helping pilots and spektrum users. Please continue and again thank you for the help

@BDTennessee

2 жыл бұрын

Thanks so much Matt B!

Great video as always. Your videos are so clear - easy to follow.

@BDTennessee

2 жыл бұрын

Trying to make radios easy, glad its working :) Thanks Rob C!

Wow would have saved hours if I watched this first

@BDTennessee

10 ай бұрын

Can be tricky for sure... Glad video helped and thanks for watching!

cool info and setup

@BDTennessee

3 жыл бұрын

Thanks Duke!

Thank you! most of this information was not in the setup guide.

@BDTennessee

Ай бұрын

Thanks Adam,im glad video helped.

just subbed as your vids are going to help me massively getting to grips and making the most of my nx8. Are these lemon receivers solid as they seem to be quite abit cheaper than the spektrum ones (with safe and as3x). I have bought 2 planes that require receivers (i am progressing from an aeroscout). If so would you recommend the lemon rx for all planes if as3x\safe is required, or just certain models? Thanks in advance.

@BDTennessee

2 жыл бұрын

TT,welcome to the channel! I use the 10 channel and 6 channel mainly non gyro in different planes. I have configured plenty of the "Stability" Rx too. If you run the "Plus" (which has Safe type mode like Spektrum) version it needs to have a good size BEC. So not really good on smaller planes as the gyro can overpower the electronics. They also had a small run of issues with the LVC set wrong on the "Plus" models. So if buying them make sure there new versions.

Thank you for your videos, they offer a lot of help but I need your advice. I have a NX8 and a 7 Channel Lemon LMN0086 GEN2. Trying to set up a Delta Wing with Stability on B and Gyro on the RKnb. The red light for Stability comes on but it doesn't change to green or green/red when B flipped. Can you help?

@BDTennessee

10 ай бұрын

Did you activate stabilization mode? Channel for mode defaults to Gear:5

Nice. Not really fan of Spectrum Radio but I did owned quite a few of them before owning Futaba Radio. With the NX series radio, though I give it another shot just for BNF’s purposes. Would you recommend the NX10 over the NX8? Thanks

@BDTennessee

3 ай бұрын

Budget allows for NX10 i would spend the extra. Hall Effect Gimbals,6000 instead of 2000 battery, 2 extra channels and magnetic charge cable. NX8 users typically buy 6000 battery so the cost becomes even closer.

I’d like to see you make a video on how to set up a new receiver with AS3X & SAFE . Thanks from Bill.

@w.j.bendellr.c.flying.1037

3 жыл бұрын

They sent me a new receiver for my plane it works and everything but it just doesn’t have AS3X and SAFE. I would like to learn how to set it up on this new receiver?

@BDTennessee

3 жыл бұрын

@@w.j.bendellr.c.flying.1037 what model is the receiver?

@w.j.bendellr.c.flying.1037

3 жыл бұрын

@@BDTennessee when I get back from vacation, I’ll take the plane apart and check the receiver I’ll get back to you, thanks very much for your help

@BDTennessee

3 жыл бұрын

@@w.j.bendellr.c.flying.1037 Copy! Let me know!

BD, Is this a Good Receiver? Do you use them on all aircraft or just the cheaper ones?Great Video 👍👍

@BDTennessee

Жыл бұрын

Lemon RX makes a good receiver. I have used them on cheap planes to good planes. I would be careful using "Plus" version on a small BEC ESC (stronger). However i like the normal Stabilizer model cause you can add satellite.

Hi BD- I’m having the same issue that Lars outlined below where when I turn off the TX function to make some modification to the nx6 I have, the motor starts to spin. I’ve tried to work through the failsafe setup instructions but that didn’t solve the issue. Do you recall how the issue was resolved? Thanks again for all the information on your channel!

@BDTennessee

Жыл бұрын

Happens when you bind receiver and radio with throttle not all the way down.

@JS-jr1wu

Жыл бұрын

Does it make a difference if the profile created has a throttle cut setup before the binding process?

@BDTennessee

Жыл бұрын

@@JS-jr1wu nope. I always bind with throttle cut off (motor on) though.

@BDTennessee

Жыл бұрын

@@JS-jr1wu good deal! Glad you got it sorted.

I use to fly my planes that have the Admiral 600 RX with a DX6. I now have the NX10 and don't like how the R knob is affecting the gains I have set in the RX. According to this video, I could put the R knob to INH, and it would be like my DX6?

@BDTennessee

2 жыл бұрын

Correct. When i setup planes do the same. Get the gains where i want them and INH the Knob adjustment so doesnt bump it or gets moved.

@twincitymoo7141

2 жыл бұрын

@@BDTennessee Thanks for the response.

@BDTennessee

2 жыл бұрын

@@twincitymoo7141 welcome! Anytime! :)

Where do I plug in my 2wire UBEC lead?

@BDTennessee

Жыл бұрын

Plug into channel 5 which is open.

BD. With that empty chanel 5 port could you power some led lights or would that mess with the receiver 🤔🤔🤪

@BDTennessee

2 жыл бұрын

Should work since its just pulling power.

Do you use expo and high rates/low rates on this receiver if so do you assign it to a separate switch or the switch that you use for Gyro fight modes? Thx

@BDTennessee

2 жыл бұрын

You can use high or low rates assign to different or same switch in the "D/R and Expo" menu. I would separate them to different switches.

@jelly-qs5fy

2 жыл бұрын

@@BDTennessee thx, do you find yourself using expo and high/ low rates with tge lemonrx ? Or does the stabilizer do enough for you

@BDTennessee

2 жыл бұрын

@@jelly-qs5fy rates and expo are configured for each pilot preference. They are for control and gyro is for stability.

Hi BD, Thanks for yopur great videos. Have had a little problem (Accident), installed the lemon Rx on my FMS PA 18. After preflight check I needed to go to Systems setup on my NX8. Pushing the roller, - the motor started.... cutting my had. I cannot for sure if Throttle CUt was ON or OFF. What did I do wrong ???? Hope you can advise.

@BDTennessee

2 жыл бұрын

Lars, sorry to hear about your injury :( If you go to System Setup it turns off the RF to the plane. So the plane think its lost signal and goes into fail safe mode. You have done 1 of 2 things. 1) Bound TX and RX without throttle being in lowest position. 2) Bound with trim at lower position and raised the trim after causing it to give the plane a false throttle input. So what needs to be done is put your throttle trim to (0) and rebind TX and RX with the throttle stick all the way down. Do this stuff with the prop off. Also you can try doing same thing of going to system setup and verify you done this correctly.

@larsbrygmann4221

2 жыл бұрын

@@BDTennessee Thank you very much. Will follow your instructions, you are the best 👍🥂🛩

@BDTennessee

2 жыл бұрын

@@larsbrygmann4221 Lars thanks! Reach out to me anytime!

@larsbrygmann4221

2 жыл бұрын

@@BDTennessee Hi, I tried to follow your instructions by doing: 1) Did bind between TX and RX with throttle i 30% When going to System setup - Motor starts... 2) Did bind between TX and RX with throttle trim in lowest position, throttle stic in lowest position, - after bound I raised it to 0. When going to System setup - Motor starts... What am I doing wrong.

@BDTennessee

2 жыл бұрын

@@larsbrygmann4221 thats the problem is your binding with the throttle trim at the lowest setting then raising to (0). I commented on your facebook post and that was 1 of the 2 setup issues i knew you was doing wrong :/ Bind TX and RX then leave trim alone. Also make sure throttle cut is lower than throttle value. You can bind the TX and RX at (0) trim.Main thing is throttle "stick" in lowest position and once you bind dont move throttle trim at all...

BD can you mount the Lemon receiver upside down in a plane? Or does it have to be right side up

@BDTennessee

2 жыл бұрын

So mounting to the bottom side of something. Yes you can,make sure to get the gyro correction working in the proper direction (Dip switch changes if needed).

@richardfoster3242

2 жыл бұрын

@@BDTennessee Thanks

@BDTennessee

2 жыл бұрын

@@richardfoster3242 anytime! :)

Can you show this on a ar620 spectrum receiver that is what we all have.

@BDTennessee

2 жыл бұрын

AR620 doesnt have as3x or safe. Spektrum does gyro setup in forward programming too.

@boss2234

2 жыл бұрын

@@BDTennessee yes I realize that but how do I get the reflex to work with the ar 620 I have a NX 8 and all 6 channels of the receiver taken with the norm flaps gear, elevator Ext. Can I put the reflex on a switch and how do I get it activated. That is why we got the AR 620. Not seeing a need for a receiver with as3x. Because of the reflex. Thanks

@BDTennessee

2 жыл бұрын

@@boss2234 Ok,i understand what your asking about. So with a external gyro like reflex on FMS,you need a extra channel to operate the modes. You will notice Reflex has a PWM lead. That connects to open channel and controls the modes. So you need a 7 channel receiver at least to have 3 modes on the gyro.

@boss2234

2 жыл бұрын

@@BDTennessee thanks

@BDTennessee

2 жыл бұрын

Your welcome! Here is setup for switch assignment System Setup > Channel Assign > Channel 7 Aux 1 > Assign the switch you want to control modes (Example Switch C , Channel 7 Aux 1: C)

With this receiver can you fly the plane in what you called the stabilized or SAFE mode OR is that mode just used for panic recovery to get your plane back to level? I find the LEMON Plus explanation of this mode very confusing. Thanks.

@BDTennessee

3 жыл бұрын

You can fly in the mode too. So you can use for Panic recovery or self leveling flight mode which also limits the bank angle. It works similar to Spektrum Safe mode if you have used it.

@BillKisel

3 жыл бұрын

@@BDTennessee Thanks. I got one for my FT Simple Cub and look forward to seeing how close the leveling mode compares to SAFE. I have two other planes with SAFE so I'm familiar with and comfortable with fling in SAFE. I got the Lemon Plus because the Spektrum receiver with SAFE is very pricey compared to the Lemon Plus.

@BDTennessee

3 жыл бұрын

@@BillKisel id be interested to hear your comparison between the two brands. Also if your installing in a plane without retractable landing gear you can setup 2 simpler ways. 1) The default is A and you dont have retractable gear so you can just use A for the Gyro. (Only need to flip Dip switch 4 and 5) 2) Go into channel Assign and change the "Gear : A" to different switch and done (if you want different switch than A). You dont have to move the other stuff around in the second menu on either one.

@BillKisel

3 жыл бұрын

@@BDTennessee BD I'm new to this RC flying hobby... the SAFE I'm familiar with is on the control board of my Sport Cub S 2 and my UMX Turbo Timber it is not a separate Spektrum receiver like you'd find in larger HH planes and sold separately for PNP planes. An obvious difference between the Lemon Plus and the Spektrum with SAFE is the price with the Spektrum costing nearly twice as much. My sense from watching YT videos of bot is that the Lemon appears, to me, to be easier to program. With the Lemon you can only have one of two levels of "SAFE"; I think that with Spektrum's forward programming you can set many levels of SAFE between maybe a max high and low. I'm pretty certain there are many other differences not related to "SAFE" between the two receivers. I've only had two flights using the Lemon as compared to hundreds with SAFE mode on my other two models. The Lemon level flight mode in my FT Simple Cub is doing pretty much what SAFE mode does for my other planes but perhaps not as tuned or refined. I think for a better comparison you'd want to experiment by using the two receivers in the same model. You'd also want the flying to be done by a more experienced pilot than me. Take care.

@BDTennessee

3 жыл бұрын

@@BillKisel I have experience with both and the differences.Always like to get feedback from others on their experience. Thanks for sharing!

BD, I have nx8. Trying to bind to lemon 34z. 3nip, none will bind! Ideas? B

@BDTennessee

Жыл бұрын

What receiver Lemon you trying to bind?

@brucepearson6322

Жыл бұрын

@@BDTennessee 34z Confirmed, bad batch of rxs.

@BDTennessee

Жыл бұрын

@@brucepearson6322 copy.I see thats the new 6 channel diversity without stabilizer. I have the older version and never issue. However new products can be faulty sometimes. Who did you order through?

@brucepearson6322

Жыл бұрын

@@BDTennessee from lemon. They said they would replace. What I did for now was remove the case of an ar410. Fits the space the same.

@BDTennessee

Жыл бұрын

@@brucepearson6322 Copy. Glad to hear Lemon is replacing.

Howdy! Great info. I have a few questions to start. 1. How do you know they are the newer models? 2. Can you change the gains via forward programming or only on the dial switch? 3. When you make those gains can you capture them? Otherwise, each time you fly you will have to adjust, correct? 4. Can you mount these in any position (except upside down) like the spektrum receivers? 5. Can you use all the spektrum satellite receivers with these? 6. Please do a video setting up the 10 channel version of these receivers!! 🙂 Thanks in advance for taking the time to respond. Jayson

@BDTennessee

Жыл бұрын

1) Most retailers will have newer models or direct from Lemon. 2)Lemon doesnt support FP,thats Spektrum patent. 3)Cant capture the gains.However if set properly shouldnt need too. Saying that,you can adjust with dial as needed. 4)Mount any position and use "Dip Switches" to change correction to match proper surface direction. 5) I personally use same brand remote or satellite. 6) 10 channel sets up same way.However they have new v2 models being released which you dont have to do this step anymore :)

@jaysonfarmer157

Жыл бұрын

@@BDTennessee thanks! Take care!

@jaysonfarmer157

Жыл бұрын

@@BDTennessee thanks BD!!

I am very sorry but absolutely do not understand the logic behind your explanation. I fly and configure racing drones and aerobatic aircraft and use different systems but mainly spektrum. I am an IT crack and used to several programming languages. I totally fail to understand the logic behind the Spektrum channel and switch assignments to control the gyro. Could you please try and explain in greater detail beginning in the TX as it is clear which channel will be/is used on the RX (Ch6). What do I have to enable to use the gyro in the first place ? The manual is absolutely not helpfull at all Thank you very much in advance. It seems there are 3 places no less one has to enable or adjust to get it working ?

@BDTennessee

Жыл бұрын

Lemon Rx you have to move gear and flaps up a channel (Gear to 6 and Flaps to 7). Gyro works off Channel 5/Gear. So if you leave the gear on 5, it will toggle the gyro.If using a non retractable gear plane,you dont need to do this configuration. Spektrum doesnt have this because the gyro can be put on a spare channel. (example channel 7).Allows 6 normal channels and a gyro toggle.

@liamclarke7162

Жыл бұрын

Hey, I was wondering if there was any way to have the gyro always on so that you can have a 6 channel model with a 6 channel transmitter. Thank you.