Slipping Clutch Kickstart - Clutch Adjustment Semi Auto Honda Engine CT70 Z50 Mini Trail Monkey Dax

My Website: VintageHondaMinis.com
Ebay Store - www.ebay.com/usr/vintagehonda...
Help support this channel by supporting me via paypal donate -
www.paypal.com/donate?hosted_...
Slipping clutch, kickstarting feels funny and will not turn crank on the Honda Z50, CT70 or ATC70 (Pull Start) etc.? Lets start with the basics and change the unknown oil and make some easy clutch adjustments to see if symptoms improve. Check out my other video on how to get into the clutch side of engine and replace the discs if needed (Link below)
Clutch disc replacement procedure on Z50 CT70 ATC70 etc. Semi Auto 3 speed transmission:
• Clutch Service Repair ...
Located Orlando, FL
Check out my other page on Facebook:
/ vintagehondaminirestor...

Пікірлер: 61

  • @jamesbeaumont1202
    @jamesbeaumont12023 жыл бұрын

    Painted nails what's all that about

  • @johnsn10
    @johnsn10 Жыл бұрын

    The painted fingernails are distracting

  • @johntucker9346
    @johntucker9346 Жыл бұрын

    why are your finder nails painted

  • @simmosimmo100
    @simmosimmo100 Жыл бұрын

    Stop with the nail varnish.

  • @myleslong9326
    @myleslong93263 жыл бұрын

    What’s with the fingernails

  • @prcaroo1
    @prcaroo1

    Y do u have painted nails 🤔

  • @mmetz1877
    @mmetz1877

    Dude, what’s with the nail polish?

  • @jasonhendrie5411
    @jasonhendrie54113 жыл бұрын

    This is just what I need my 83 ct70 kickstarter is slipping

  • @seffdog1177
    @seffdog11773 жыл бұрын

    Good tip about the car oil compared to bike oil

  • @keithstewart4750
    @keithstewart47503 жыл бұрын

    Thanks. New clutch fibers and my clutch grabs so it won’t idle. I turned it back CCW to resistance and it’s better, not great, but shifting get sticky. Also when shifter is held down or up I can still feel some clutch engagement . Any other ideas it could be?

  • @dannilaser16
    @dannilaser16 Жыл бұрын

    Awesome video.

  • @opinion4246
    @opinion4246 Жыл бұрын

    Thanks very helpful👍

  • @5yri5
    @5yri52 жыл бұрын

    Thank you

  • @johnsn10
    @johnsn10

    My 2017 crf50 moves on its own when put in gear and the idle is set correctly. It sat for 2 years so could it be stuck clutch plates? If I put the bike on a stand and put it in gear the rear wheel starts spinning and I can’t stop it.

  • @irocss85
    @irocss852 жыл бұрын

    I just bought a used pit bike 110cc I've heard there all the same. My stud WILL NOT TURN either way with the nut completely off. I wanted to adjust it because it bangs into gear hard from neutral even after lowering the idle. I did change the oil. And possibly at some point it had the wrong oil in it. But that wouldn't explain why the stud is stuck. How do you replace that? Mines a tao tao pitbike. Not sure where to get that part and the side cover gasket.

  • @SergeoGabrielloGomez
    @SergeoGabrielloGomez2 жыл бұрын

    Best way to replace that little adjust stud ?

  • @chavasrt4428
    @chavasrt4428

    helo any idea why my z50r wont move under its own power even on first gear ?

  • @stevebuckmaster13
    @stevebuckmaster13 Жыл бұрын

    Josh , Another great video, my bike is doing the same thing, sometimes it has compression and sometimes not , i will try these and see what happens . Did you get my tip i sent you ?

  • @Dougie33
    @Dougie33 Жыл бұрын

    6:50

  • @troycotsenmoyer6736
    @troycotsenmoyer67362 жыл бұрын

    Can you tell by looking at the adjusting screw for the clutch if your clutch plates are worn?