About to start building my first CNC (an MPCNC Primo) and am planning to use Bart Dring's 6-pack and run fluidnc. This walk through was very helpful for getting an overview of the firmware before I dive in.

Thanks for the video , helped me out setting up an MKS tinybee...

Very insightful video! Thanks for this. I have managed to get everything running for a machine with one X and two Y motors with dual endstops. I have moved the Z motor over to be a second Y motor and everything moves as desired. But when I home the Y axis it doesn't bounce back, it just sits there and then fails. The X axis homes perfectly. Any idea why the Y axis is not homing right?

Bravo for your explanations I have the same card as you I would like to configure my laser which is CoreXY which yaml file should I take? Is the laser connected to TTL? Do you use limit with 3 wires?

How easy it would be to setup a CO2 Laser with this board? I've seen people selling shields with ESP32 and FluidNC for K-40 lasers to be able to use Lightburn directly but they asked arround 100-110€ shipped

Thanks for the video! All the config files I have found do not show the control: and macros: ... are there any sample config files showing these? - it's strange they have been left out

Thank you for posting this. I am gonna use fluidnc for the first time too. I am building impact etching machine, it will have a diamond engraving head instead of laser. I am little confused with double y axis though. Is the second y motor gonna use the motor driver of z axis ? Or one driver is enough for 2 y axes?

@brakthehun

Жыл бұрын

Depends on if your dragging or oscillating the diamond. I would use 2 drivers if your dragging it.

@yerbolatabdrafikov2731

Жыл бұрын

@@brakthehun I am gonna oscillate it. If I want to use 2 drivers for y axis then I have to add motor1 under y axis parameters, but I will have to copy all parameters from the motor0 of z axis in config file. In this case, second y axis motor is gonna use pins of z axis on the board. Am I right? Thank you in advance !

@brakthehun

Жыл бұрын

@@yerbolatabdrafikov2731 yup!!

I Just bought the same card as you mks dlc32 2.1 for my k40 laser, do you happend to have the pins schematic ? wich # goes into what connection?

@brakthehun

Жыл бұрын

I've helped with a swap,, but I don't have a schematic. I just followed the wires.

I have a mks dlc32 and I configured it following your instructions and it works fine but the G53 boot code part does nothing, could you please help me?

😍

Mine keeps telling me it can't find the config file I upload. Is there a way fix to this?

@brakthehun

Жыл бұрын

I haven't seen that happen. I'm pretty new to this board and platform myself.

Nice job on the tutorial, I was able to get about 90% through it and got stuck on the dual Y motors part. I'm using a MKS DLC32 v1.1 board, I have my yaml setup just like you did in the video by copying the Z motor0 to the Y motor1. My problem is that now after reloading the yaml I get Y and Z moving together and z will not home anymore. Any ideas what I'm doing wrong? I commented out the extra motors so I could continue to work on it. But you can see below the Y and Z where I made the changes. This is on a Shapeoko 2 CNC router. board: MKS-DLC32 V1.1 name: Shapeoko2 meta: (02.11.2023) by GorLeeRob kinematics: Cartesian: stepping: engine: I2S_STATIC idle_ms: 0 pulse_us: 4 dir_delay_us: 1 disable_delay_us: 0 axes: shared_stepper_disable_pin: I2SO.0 x: steps_per_mm: 80 max_rate_mm_per_min: 18000.000 acceleration_mm_per_sec2: 1500.000 max_travel_mm: 269.000 soft_limits: true homing: cycle: 1 positive_direction: false mpos_mm: 0.000 feed_mm_per_min: 300.000 seek_mm_per_min: 5000.000 settle_ms: 500 seek_scaler: 1.100 feed_scaler: 1.100 motor0: limit_neg_pin: gpio.36:low hard_limits: false pulloff_mm: 2.000 stepstick: step_pin: I2SO.1 direction_pin: I2SO.2 y: steps_per_mm: 80 max_rate_mm_per_min: 12000.000 acceleration_mm_per_sec2: 300.000 max_travel_mm: 760.000 soft_limits: true homing: cycle: 2 positive_direction: true mpos_mm: 0.000 feed_mm_per_min: 300.000 seek_mm_per_min: 5000.000 settle_ms: 500 seek_scaler: 1.100 feed_scaler: 1.100 motor0: limit_neg_pin: gpio.35:low hard_limits: false pulloff_mm: 2.000 stepstick: step_pin: I2SO.5 direction_pin: I2SO.6:low #motor1: #limit_neg_pin: gpio.34:low #hard_limits: false #pulloff_mm: 6.000 #stepstick: #step_pin: I2SO.3 #direction_pin: I2SO.4 z: steps_per_mm: 806.451 max_rate_mm_per_min: 9350.000 acceleration_mm_per_sec2: 500.000 max_travel_mm: 200.000 soft_limits: true homing: cycle: 3 positive_direction: true mpos_mm: 0.000 feed_mm_per_min: 1800.000 seek_mm_per_min: 1000.000 settle_ms: 500 seek_scaler: 1.100 feed_scaler: 1.100 motor0: limit_neg_pin: gpio.34:low hard_limits: false pulloff_mm: 6.000 stepstick: step_pin: I2SO.3 direction_pin: I2SO.4 #motor0: #limit_neg_pin: NO_PIN #hard_limits: false #pulloff_mm: 6.000 #stepstick: #step_pin: I2SO.8 #direction_pin: I2SO.9 i2so: bck_pin: gpio.16 data_pin: gpio.21 ws_pin: gpio.17 spi: miso_pin: gpio.12 mosi_pin: gpio.13 sck_pin: gpio.14 sdcard: cs_pin: gpio.15 card_detect_pin: NO_PIN control: safety_door_pin: NO_PIN reset_pin: NO_PIN feed_hold_pin: NO_PIN cycle_start_pin: NO_PIN macro0_pin: gpio.33:low:pu macro1_pin: NO_PIN macro2_pin: NO_PIN macro3_pin: NO_PIN macros: startup_line0:G53x-220 #just added this today startup_line1:G92X-0 #just added this today macro0: $SD/Run=lasertest.gcode macro1: $SD/Run=home.gcode macro2: macro3: coolant: flood_pin: NO_PIN mist_pin: NO_PIN delay_ms: 0 probe: pin: gpio.22 check_mode_start: true Laser: pwm_hz: 5000 #L on Beeper / IN on TTL output_pin: gpio.32 enable_pin: I2SO.7 disable_with_s0: false s0_with_disable: false tool_num: 0 speed_map: 0=0.000% 0=12.500% 1700=100.000% # 135=0mA 270=5mA 400=10mA 700=16mA user_outputs: analog0_pin: NO_PIN analog1_pin: NO_PIN analog2_pin: NO_PIN analog3_pin: NO_PIN analog0_hz: 5000 analog1_hz: 5000 analog2_hz: 5000 analog3_hz: 5000 digital0_pin: NO_PIN digital1_pin: NO_PIN digital2_pin: NO_PIN digital3_pin: NO_PIN start: must_home: true #just added this today # 5,18,19,22,23,25,26,27,32,33,39,I2SO.7 # SDA 0 / SCL 4

@brakthehun

Жыл бұрын

Post your Yaml

@gorleerob3929

Жыл бұрын

Hi Tony, sorry I had a little trouble posting. I'm going to try again. Thanks for your help., Gordon I commented out the extra motors so I could continue to work on it. But you can see below the Y and Z where I made the changes. This is on a Shapeoko 2 CNC router. board: MKS-DLC32 V1.1 name: Shapeoko2 meta: (02.11.2023) by GorLeeRob kinematics: Cartesian: stepping: engine: I2S_STATIC idle_ms: 0 pulse_us: 4 dir_delay_us: 1 disable_delay_us: 0 axes: shared_stepper_disable_pin: I2SO.0 x: steps_per_mm: 80 max_rate_mm_per_min: 18000.000 acceleration_mm_per_sec2: 1500.000 max_travel_mm: 269.000 soft_limits: true homing: cycle: 1 positive_direction: false mpos_mm: 0.000 feed_mm_per_min: 300.000 seek_mm_per_min: 5000.000 settle_ms: 500 seek_scaler: 1.100 feed_scaler: 1.100 motor0: limit_neg_pin: gpio.36:low hard_limits: false pulloff_mm: 2.000 stepstick: step_pin: I2SO.1 direction_pin: I2SO.2 y: steps_per_mm: 80 max_rate_mm_per_min: 12000.000 acceleration_mm_per_sec2: 300.000 max_travel_mm: 760.000 soft_limits: true homing: cycle: 2 positive_direction: true mpos_mm: 0.000 feed_mm_per_min: 300.000 seek_mm_per_min: 5000.000 settle_ms: 500 seek_scaler: 1.100 feed_scaler: 1.100 motor0: limit_neg_pin: gpio.35:low hard_limits: false pulloff_mm: 2.000 stepstick: step_pin: I2SO.5 direction_pin: I2SO.6:low #motor1: #limit_neg_pin: gpio.34:low #hard_limits: false #pulloff_mm: 6.000 #stepstick: #step_pin: I2SO.3 #direction_pin: I2SO.4 z: steps_per_mm: 806.451 max_rate_mm_per_min: 9350.000 acceleration_mm_per_sec2: 500.000 max_travel_mm: 200.000 soft_limits: true homing: cycle: 3 positive_direction: true mpos_mm: 0.000 feed_mm_per_min: 1800.000 seek_mm_per_min: 1000.000 settle_ms: 500 seek_scaler: 1.100 feed_scaler: 1.100 motor0: limit_neg_pin: gpio.34:low hard_limits: false pulloff_mm: 6.000 stepstick: step_pin: I2SO.3 direction_pin: I2SO.4 #motor0: #limit_neg_pin: NO_PIN #hard_limits: false #pulloff_mm: 6.000 #stepstick: #step_pin: I2SO.8 #direction_pin: I2SO.9 i2so: bck_pin: gpio.16 data_pin: gpio.21 ws_pin: gpio.17 spi: miso_pin: gpio.12 mosi_pin: gpio.13 sck_pin: gpio.14 sdcard: cs_pin: gpio.15 card_detect_pin: NO_PIN control: safety_door_pin: NO_PIN reset_pin: NO_PIN feed_hold_pin: NO_PIN cycle_start_pin: NO_PIN macro0_pin: gpio.33:low:pu macro1_pin: NO_PIN macro2_pin: NO_PIN macro3_pin: NO_PIN macros: startup_line0:G53x-220 #just added this today startup_line1:G92X-0 #just added this today macro0: $SD/Run=lasertest.gcode macro1: $SD/Run=home.gcode macro2: macro3: coolant: flood_pin: NO_PIN mist_pin: NO_PIN delay_ms: 0 probe: pin: gpio.22 check_mode_start: true Laser: pwm_hz: 5000 #L on Beeper / IN on TTL output_pin: gpio.32 enable_pin: I2SO.7 disable_with_s0: false s0_with_disable: false tool_num: 0 speed_map: 0=0.000% 0=12.500% 1700=100.000% # 135=0mA 270=5mA 400=10mA 700=16mA user_outputs: analog0_pin: NO_PIN analog1_pin: NO_PIN analog2_pin: NO_PIN analog3_pin: NO_PIN analog0_hz: 5000 analog1_hz: 5000 analog2_hz: 5000 analog3_hz: 5000 digital0_pin: NO_PIN digital1_pin: NO_PIN digital2_pin: NO_PIN digital3_pin: NO_PIN start: must_home: true #just added this today # 5,18,19,22,23,25,26,27,32,33,39,I2SO.7 # SDA 0 / SCL 4

@brakthehun

Жыл бұрын

Looks good on the yaml. I think the next thing to investigate is the wiring.

@rics_zip

Жыл бұрын

​ @gorleerob3929 maybe this video can help you with that kzread.info/dash/bejne/eIOIyLavmdewm84.html " CNC Wiring Basics // FluidNC // ESP32 // TinyBee controller " It's a diferent board, but it can be a way

Hi What is meant by shared_stepper_disable_pin: I2SO.0 How is this used? And also I2S_STATIC my regards

Hi, do you know why I can't upload any other config file with changes using fluidterm as you do here 27:55 ? I have to erase all flash memory and install everything once again even when I did some little mistake in .yaml. Im getting Return -2.

@brakthehun

5 күн бұрын

@@czowiekznikad2062 I haven't had that issue. Are you making sure to select the right port in Fluid Terminal??

@czowiekznikad2062

5 күн бұрын

@@brakthehun yeah, I've selected the right COM port. I installed and uploaded older version of FluidNC (3.5.0), the same you have used and I got rid of this issue. However, I'll use an Arduino Uno to finish the project as I am using standard ESP32 DEVKIT V1 and do not have MKS DLC32. I've tried to use TXS0108E level shifters to send the signal to DM542 stepper driver, but my stepper motors are going crazy, they didn't want to move even when they were supposed to, I've erased everything from ESP32 once again and uploaded some simple code to control only one motor (X gantry), just to move and be still. And guess what happend :D All motors (other Y and Z gantry) which were not supposed to move had worked as I described in code along with the specific one I've programmed and wanted to move. The stepper motors operation is unstable, I don't know what it can be, maybe it's my skill issue in soldering as I'm doing the project on a prototype board, or some ESP32 soft problems, or just bad hardware connection. Despite all of my issues, your guide helped me a lot during the process of setting up the firmware on ESP32, everything worked perfectly, I've even had an internet connection established :D

I am building a laser pointer turret, which uses only two stepper motors. I was wanting to control it using a PS3 controller via BT. I ended up getting an MKS DLC32 board and trying FluidNC on it. Is this possible or am I just wasting time? I would appreciate any help or ideas anyone has as I am stuck :( Thank you

@brakthehun

8 ай бұрын

FluidNC can't really take a controller input like that. It's a good board to use but you may need to write custom firmware.

@TMRu22311

8 ай бұрын

@@brakthehun Thank you for the reply. I think you are right and since I am not much of a coder, I may try something else. I was wondering if I could use FluidNC wifi to control it with a phone or tablet.

@TMRu22311

8 ай бұрын

@@brakthehun Thank you Anthony! Is it possible to upload Arduino code to the DLC32? I have all the code for this project and using ChatGPT I had it rewrite the code giving it the gpio pin ref for the DLC32. I just wasn't sure if that was possible or not. I don't want to brick the board.

@brakthehun

8 ай бұрын

Yes. You may need to connect SDA to G to boot it in to upload mode.@@TMRu22311

@TMRu22311

8 ай бұрын

@@brakthehun I am trying to upload FluidNC on the MKS-DLC32 v2.1. Everything seemed to be okay except for wifi. I cannot connect with ESPD (Connection failed! is your FW correct?) And in FluidTerminal I get this error: wifi : AP has neither DSSS parameter nor HT Information. What am I missing? Is there a wifi config file I was supposed to edit?

If I try to open Fluidterm it opens the window but then just closes after a few seconds. I have tried 3 different computers and get the same result, anybody have any suggestions?????

I do not know what happened with mine was fallow you step by step and after installing the WIFI file I lost connection and now the computer will not connect and now the off line screen hat came with the board is blank NOT GOOD

@brakthehun

Жыл бұрын

Fluidnc does not support screens by default. Is it the v2.1?? Does FluidTerm connect??

@rodmack4682

Жыл бұрын

@@brakthehun just redid everything step by step as I watched the video everything worked good this time now next is to wifi or BlueTooth it