Пікірлер

• 
  @faustoart2 күн бұрын

  very good tutorial, I followed it, I shorted the electriciby of the full building (yet dont understand how I did it) but no its working nicely, so thank you!

• 
  @czowiekznikad20625 күн бұрын

  Hi, do you know why I can't upload any other config file with changes using fluidterm as you do here 27:55 ? I have to erase all flash memory and install everything once again even when I did some little mistake in .yaml. Im getting Return -2.

• 
  @brakthehun5 күн бұрын

  @@czowiekznikad2062 I haven't had that issue. Are you making sure to select the right port in Fluid Terminal??

• 
  @czowiekznikad20625 күн бұрын

  @@brakthehun yeah, I've selected the right COM port. I installed and uploaded older version of FluidNC (3.5.0), the same you have used and I got rid of this issue. However, I'll use an Arduino Uno to finish the project as I am using standard ESP32 DEVKIT V1 and do not have MKS DLC32. I've tried to use TXS0108E level shifters to send the signal to DM542 stepper driver, but my stepper motors are going crazy, they didn't want to move even when they were supposed to, I've erased everything from ESP32 once again and uploaded some simple code to control only one motor (X gantry), just to move and be still. And guess what happend :D All motors (other Y and Z gantry) which were not supposed to move had worked as I described in code along with the specific one I've programmed and wanted to move. The stepper motors operation is unstable, I don't know what it can be, maybe it's my skill issue in soldering as I'm doing the project on a prototype board, or some ESP32 soft problems, or just bad hardware connection. Despite all of my issues, your guide helped me a lot during the process of setting up the firmware on ESP32, everything worked perfectly, I've even had an internet connection established :D

• 
  @barryleeder90296 күн бұрын

  Can u tell me what settings for mirror I got a olm3 10w and trying to do a test card

• 
  @pipinval7 күн бұрын

  Everything is going well, until I put on "$radio" . Get error. Anyone knows how to solve this?

• 
  @Glasairman8 күн бұрын

  Like you enclosure very much, Do you have a cut list? Looks like alu profile 2020 Hammerhead 5, correct? (In German we say Nut = Groove)

• 
  @md.asrafulislam143610 күн бұрын

  How to set power max and powre min, only power max comes in my apps

• 
  @brakthehun10 күн бұрын

  @@md.asrafulislam1436 go to the console and ask it. Type in $$ and hit enter. Register 30 ($30) will tell you the value to fire the laser at max power.

• 
  @777smitty414 күн бұрын

  I abandoned ugs and went to lazergrbl same issue if I hit home it gives error code pin9 x limit pin10 y limit and pin 12 is torch on also can’t get it to come on

• 
  @brakthehun14 күн бұрын

  @@777smitty4 disable hard stops?? Plasma torches can be very noisy electrically.

• 
  @777smitty414 күн бұрын

  At this point torch is not connected only the optical relay just for testing

• 
  @richardbrown229015 күн бұрын

  Great video. Could you do a add-on on LaserGRBL version 7.X.X. There seems to be a lot of changes between 3.x.x and 7.x.x. Thanks

• 
  @brakthehun14 күн бұрын

  @@richardbrown2290 It is coming!!

• 
  @kernowcoinringscornishcoin399915 күн бұрын

  Hi when using laser grbl when I attempt to jog the y axsis the x axsis moves instead any ideas why this would happen?

• 
  @brakthehun15 күн бұрын

  @@kernowcoinringscornishcoin3999 what machine?? Is it different with other gcode senders???

• 
  @kernowcoinringscornishcoin399915 күн бұрын

  @@brakthehun atomstack p7 only just set up machine yesterday and using laser grbl

• 
  @kernowcoinringscornishcoin399915 күн бұрын

  @@brakthehun would the machine jog in accordance with the orientation of the picture I'm carving

• 
  @brakthehun15 күн бұрын

  @@kernowcoinringscornishcoin3999 it might be the orientation of the machine.

• 
  @kernowcoinringscornishcoin399915 күн бұрын

  @@brakthehun machine as in the laser or my laptop if its the laser can this be changed

• 
  @samsesam348622 күн бұрын

  ok, can you please also show me how to connect the Atomstack to the computer via Wifi ?

• 
  @krzysztofrucinski654126 күн бұрын

  You are stupid because on the ESP32 board there are WIN and GND pins to which you connect +5v and ground you did not have to cut the socket. This has nothing to do with the professionalism you mention.

• 
  @agajgiv28 күн бұрын

  WOW.. It's really wonderful.. Thank you for your effort, my friend ❤

• 
  @ianjohn885Ай бұрын

  thank you so much man, i have been looking for a good starter video on how to use this software and your video is perfect. thank you soooo much man ill sub and keep a look out for more

• 
  @baneofyourexistence5911Ай бұрын

  “Pull these off… maybe…” What an electrician thing to say haha

• 
  @jondoe5866Ай бұрын

  Do you have any plans on this design is love to do one.

• 
  @GustavoGuevara123Ай бұрын

  Gracias por compartir lo que sabes, me ha servido un montón, armé una máquina CNC y con tus aportes he podido configurarla, un fuerte abrazo 🫂.

• 
  @joannamclafferty6091Ай бұрын

  I close my eyes and see chuy from pawn stars

• 
  @brakthehunАй бұрын

  Maybe I'm him in the future. Ha!!

• 
  @PremalathaParthaPremАй бұрын

  Is this suitable for atomstack S10 pro also?

• 
  @brakthehunАй бұрын

  Should be

• 
  @corban111Ай бұрын

  Great tutorial 👌 Handy little tip... you can use a putty (here in AU we have Blu-Tack) to temporarily hold the board and wires while soldering. I use this trick all the time for electronics repairs and assembly

• 
  @darkblaze40Ай бұрын

  o7 really needed this was stupid enough to not put the strip.show outside the for loop lol

• 
  @brakthehunАй бұрын

  I did the same thing at first

• 
  @deejaydelacerda2 ай бұрын

  Excellent video

• 
  @edinmak92262 ай бұрын

  Hi, I have an atomstack s20 max. The power of the laser is 18-20w. They cannot cut plexiglass (acryl) 3 mm at all. Is the problem that the laser power is low, or did I not set good parameters for cutting? I use the lightburn program

• 
  @brakthehun2 ай бұрын

  The AtomStack S20 is a blue laser. Clear plexi does not absorb blue. It passes right through. To engrave / cut clear plexi - you will need a different laser. People usually use a CO2 laser because it is a far infrared beam. at that wavelength,, the acrylic completely absorbs the energy. Unlike blue that passes right through,, the plexi can't pass the IR and it absorbs the energy letting it engrave / cut.

• 
  @edinmak9226Ай бұрын

  @@brakthehun THAN YOU

• 
  @brendaellerridenour91352 ай бұрын

  Thank you soooo much for taking time to explain how to use a laser so a layman as myself can understand.

• 
  @3dsteveo7652 ай бұрын

  Awesome!

• 
  @3dsteveo7652 ай бұрын

  thank you so much these are great help!

• 
  @denispearse-si1oo2 ай бұрын

  right click, adjust image. lightburn

• 
  @brittanydemaria48772 ай бұрын

  Do you have to connect the machine? Can I just send files to an SD card with the Creality Falcon 10W?

• 
  @brakthehun2 ай бұрын

  I see that it has the SD slot but I don't see a way to access it from the front controls. You may have to connect directly

• 
  @erinpacker1182 ай бұрын

  Thanks Tony! -Erin

• 
  @777smitty42 ай бұрын

  Great video for GRBL But I have a little different setup looking for help arduino running separate drivers with ugs how would I connect switches I can’t find any advice on my setup

• 
  @brakthehun2 ай бұрын

  What's your setup??

• 
  @777smitty42 ай бұрын

  I don’t have the GRBL shield I’m running straight off arduino unio

• 
  @friedrichmandel25742 ай бұрын

  Thank you for your detailed tutorials ... helping me a lot as a beginner. If I had a wish to the LaserGRBL programmer ... I would like to have a second indicator for the actual laser power - just like the buffer "VU meter". This would help to utilize the full dynamic range of the laser power (instead of reading the actual Sxxx values while running).

• 
  @brakthehun2 ай бұрын

  He's very responsive. Request that!!

• 
  @yalafilmsdavidjwoodall92012 ай бұрын

  Great vid for a newbe like me. How do I reduce power?

• 
  @marcuscoronado48552 ай бұрын

  how to installl this software?

• 
  @brakthehun2 ай бұрын

  Windows only. lasergrbl.com

• 
  @RicoBogdan3 ай бұрын

  very good video but why is the x axis 410 cuz im pretty sure the work are is 400 x 400?

• 
  @brakthehun3 ай бұрын

  Yours might be slightly different than mine.

• 
  @lasandrafernandes30453 ай бұрын

  Can you tell me how you got the parameter custom button?

• 
  @brakthehun3 ай бұрын

  The latest version of LaserGRBL has them by default but I have a video that shows you how to make them: kzread.info/dash/bejne/qX-brMeqetnFqZs.html This was before they defaulted to have a perimeter button.

• 
  @lasandrafernandes30453 ай бұрын

  @@brakthehun got it.Thank you 😁

• 
  @dreadfulgentleman3 ай бұрын

  Thank you so much for creating this video. I learned a lot from it!

• 
  @simonmsiza66673 ай бұрын

  Thanks for helping me out.just to make sure when the driver is powered and stepper motor is not connected the a driver will burn out

• 
  @annnaziathrahman26463 ай бұрын

  Thank you so much for the this! This is literally what I needed for the project, as coding noob, this was mighty helpful, keep on making these solid videos!

• 
  @remad17773 ай бұрын

  The centreing and framing buttons are grey in laserGRBL even when successfully connected to my atomstack. I have just set it up for the first time. Does anyone know why this might be?

• 
  @brakthehun3 ай бұрын

  Load a file first. Make sure you're communicating

• 
  @remad17773 ай бұрын

  @@brakthehun Thank you

• 
  @chanchalsakarde27683 ай бұрын

  Can it be possible to draw "Thread Art" also called as "string art"

• 
  @brakthehun3 ай бұрын

  It's a plotter so sure. You can even attach a finer pen to get a more thread like look.

• 
  @godin82623 ай бұрын

  I don't have the import Raster Image when I open and image it place the image direct on work space and the work space change dimension depend on the image I load and it is impossible to move the image on the work space. What is wrong in my set up? I want to figure out why before buying and other software. Thanks if someone could help

• 
  @0Logan053 ай бұрын

  Remember when Democrats despised MLK..😂..I Do… Dems are truly Evil.

• 
  @campfiretrailers28483 ай бұрын

  Just what I was looking for! TY

• 
  @azinfidel64613 ай бұрын

  Thanks for the video , helped me out setting up an MKS tinybee...

• 
  @adam.southside3 ай бұрын

  Thanks for the video! All the config files I have found do not show the control: and macros: ... are there any sample config files showing these? - it's strange they have been left out

• 
  @peterloring73613 ай бұрын

  Anthony, Thank you sooooo very much for this series of videos. You've covered all of the steps that other sites were missing. Your pacing and attention to detail are excellent. I also appreciate that you are not hyping up every video, you are just presenting the information. This makes it much more enjoyable to learn from. Thanks again.

• 
  @mhguidry3 ай бұрын

  do you know a way to enable wifi on boot after you first setup wifi?

• 
  @lizlewis78174 ай бұрын

  How do you Home? I have not found it in another video that you mentioned. Thanks

• 
  @brakthehun4 ай бұрын

  Not all lasers have homing. YOu can force try it by typing in $H in to the console and hitting enter.

• 
  @FairlyOddball4 ай бұрын

  Thanks! you've helped a lot!

• 
  @ourrenovationreality65024 ай бұрын

  Thanks for posting. I got a laser off a friend who could not get tit running. I have it up and running, but the Z axis only goes 1 direction when using either arrow. Any thoughts? If I reverse the Y1 and Y2, it just goes in the reverse direction. I tested in LightBurn and it is the same so I am assuming its a hardware or working issue tho everything looks correct best I can tell

• 
  @jonadabdsable4 ай бұрын

  Beautiful project. My friend, I managed to run this project only once and I had to download it again and the IDE won't let me. Is this code open or not? Grateful.