Fail fail fail fail... Cut scene... Magically seated. Cool video

Didn’t manage to fully seat the bead by jumping, but it did seat just enough to get it to hold air and get the tire mounted after fighting it for a half hour. Thanks for the video. ❤

This worked great when my normal ratchet strap approach failed. One key was to use a larger diameter tire to set the new tire on while jumping. And then I flipped it over to begin to set the bead on the other side. Thanks so much.

@alandackombe3365

2 күн бұрын

This worked great for me.

I just tried this after trying the flame and ratchet way that didn't work and this way worked straight away cheers mate 👍

You look like me jumping up and down on the tire to seat the front tire bead.But the second tire underneath is a go.I think i will try that.Thankyou very much.

Awesome tip about removing the valve stem to flow a lot more air. That worked for me after ratchet strap wasn't enough. 60 gal compressor at 120psi with the open valve and plenty of lube and it popped right up. Many thanks!

Thhhhhhhhhhhhhhhhhnk u, this saved my day, tried the propane like 10x times no luck, just some gnarly fires

This did work eventually. It seats one side by jumping on it hard, then you can inspect the other side to push on the tire and close the gap enough (There's usually only one gap) to get the air going in to do the rest of the work. I would say however that you should then just let the air all leak out before trying to insert the schrader valve. Don't worry, if you have inflated it the beads are seated and won't come off. Then you won't risk shooting the little valve off in space, maybe never to be found again.

Thanks for the video man! I had a bastard of a tire and this worked

What an absolute life saver. I tried for a couple hours yesterday and may an hour today trying to mount a pair of 235 width tire on 8” wide rims. I tried in vain to seat one side (as I have done before) with a dead blow hammer. The jump in the middle of the rim did the trick. Then the lift the tire (or press down on the rim) and air up (thanks for the valve core reminder)

Excellent. a way I haven't seen before. Nice

Another tip would be to put a ratchet strap around the tire tread and ratchet as tight as you can to expand the tire towards the bead. once the bead is seated then remove the strap.

@KiloFeenix

Жыл бұрын

This doesn't always work especially if it's a wide tire

@christian84553

7 ай бұрын

This is exactly what I do with the tires on my snow blower. However I can't find a hole in the tire but it still goes flat and comes off the rim. No damage to the rim ideas would be great.

Do you think I should heat my tire up a little to loosen the rubber? I can't get the front bead to set one side will slide under the bead then the other side (of the front) will slide out

Meh, I tried the manual method for like 2 hours. Took me 1 minute with the flame and a kick. No issues except the injection mold hairs burned off. Which is probably fine. I would have loved to get it, but it fought every step of the way. I weigh 240 lb, and it wasn't enough to seat the first bead. 205/65r15 was the tire size.

Thanks

I think I'll stick with the fire method, not that easy when it's a tractor or truck Tyre...

@dylanzrim3635

11 ай бұрын

The ratchet strap or chain method is less likely to send the tire into the next state though

@johncollins8304

9 ай бұрын

@@dylanzrim3635 And you with it!

I put a tie strap around the outside of the tire and tighten it a little. Works everytime.

@RogerPack

4 ай бұрын

I had that way "not work" for me today on one tire out of two but it's definitely worth trying. Also make sure to try to pump it up with the core out...

@adamjonkie5601

2 ай бұрын

Didn’t work for me today

@m998hmmwv7

2 ай бұрын

@@adamjonkie5601 then try using a belt or a peice of rope and some soap and water

@adamjonkie5601

2 ай бұрын

@@m998hmmwv7 how tight is the strap supposed to be

@m998hmmwv7

2 ай бұрын

@@adamjonkie5601 tight enough to expand on to the high part of the rim where less air can escape. Also the quicker you can push air into the tire the better chance it will seal .

NO, just use starting fluid.

Use starting fluid and flame is safer than jumping on a slippery lubed up tire.

With a car tire, for me worked better if I attempted to seat the "back" bead first using this method (i.e. jump into the deep well side), then blew the other one out, ex: kzread.info/dash/bejne/l4t7lpmSqc7Sg6g.html but then it worked, front first did not appear to...it did work by jumping with it on another tire, thank you!

Its amazing to think that people are so dull witted that they think a little bit of starting fluid going bang is gonna be catastrophic so they'd rather work way harder to achieve the same goal...

@davidwillis5016

6 ай бұрын

Yeah but some people go way past that sweet spot and we'll blow the tire right off the wheel, I've never done it but I've talked to people that have done it or have seen happen, it sometimes takes me three or four trees before I hit that sweet spot just because if it's too much you got a situation on your hands which might hurt somebody, namely me!

Why do people think you want to hear them talk in videos??

@deepnutballz

11 ай бұрын

Shut up jackass

@m998hmmwv7

10 ай бұрын

What?? Now go sit down and be quiet

@davidwillis5016

6 ай бұрын

Because we're all different we all do things in different ways, I hope that answers your question