That ZR1 is a monster.. It will smoke the new vette C8

gives me a greater appreciation for how challenging this work can be

Not bad, considering you were using gel as a tack solution. Next time use an alcohol/water mix to tack, you will find it install much easier. You would've had a lot less difficulty with those fender inserts and fender body line if you had started there. It's easier to line up the outside edges than trying to squish the film to fit somewhere in the middle. Good on you for getting on it even though you are out of practice, most are too scared to even try. And thanks for the tint tips, your videos are great.

Mucho thanks, I have to do a very small custom xpel thing with a small cut-out, and feel more confident now with these tips.

Please post the bumper and hood if you can. You explained it better then the teachers I learned from

Great video brother! 👍🏼👍🏼

Great presentation

Looks good but you think that edge will start to peel up after a few washes? Also does the squeegee leave scuff marks on the film at all? Last question: Do you own the shop?

Question, don't you need to apply more pressure with the squeegee to get all the solution out? It looks like your lightly going over the film. Great job.

Video randomly popped up on feed and interesting tack and start point that's for sure. Definitely wouldn't put this in the how to do clear bra category though.

Çok teşekkür ederim çok detaylı

what is the spray bottle and hose attachment you use? Seems a bit better than a typical spray bottle for tight areas and has more pressure

What's the maintenance schedule like on stuff like this? Remove and replace every year, every other year? I see a lot of well-intentioned wraps and these protective films burnt on in the junk yards. If you let them go in the sun, does more harm than good.

can you buy paint protection film that isn't precut? I was thinking that would be something good to place on the front of a vehicle, especially the hood and maybe behind where the tires are and the lower part of the doors to protect against rocks and debris. The lower half of the vehicle seems to need it most.

Can you do vlogs of window tint you do in your shop? The unusual window tint jobs would be great to see :D @ TintStuff

Ppf is hard and time will build skill. If I were a customer I would have asked for a redu by the head lights. A few washes and it will start to build an edge that you can see. But good job brother, keep up the work

@DetroitTintStudio

4 жыл бұрын

Yea just like tint, it's very much its own skill. Wish I had more consistent experience going into this situation. Shop literally handed me a kit and said do the best you can.

@TheeNiCkyNuGz

4 жыл бұрын

TintStuff do a lot of plotter cut ppf, black and white paint such a pain in the ass. As long as they didn’t rush it out, owners don’t usually realize the difficulties of clear bra film installations

@TheeNiCkyNuGz

4 жыл бұрын

Xpel is doing classes in San Antonio as well to teach ppf.

Its "just" the ZR1 😂😂

@didiermejia780

3 жыл бұрын

Haha

In your opinion what harder to learn ppf or window tinting whats harder for u to do tint or ppf?

Do you need PPF sunfilm installar

So way it works wet the area put ppf pf top then squeegee the liqued out

Top 10 ,,, muito bom

I'd ask you to redo that panel.

Hi bud , I think your a badass doing tints , but for ppf your just doing all wrong , first , precut Kits are limited to wrap the edges and hard to stretch the best is work with custom pieces , second the solution , you don’t need all of that shit from xpel , all you need is softsoap hand soap antibacterial and regular tap water , and instead of hand sanitizer use 70% rubbing alcohol works the best if you use 70%tap water , and 30% alcohol, third , wrong squeegee, use 3m black rubber soft squeegee, the one you use will leave a lot of marks on the film , , fourth , you don’t need steamer if you just stretch good at the beginning, and you forgot the most important tip ! HEATGUN ALL EDGES TO AVOID PEELING, If you need more tips follow me on instagram geoproppf_chicago btw I suck doing tints ! 😁 good luck

@adnan-khan

3 жыл бұрын

AGREED! So many things wrong with this ppf installation. Definitely not a how to by any means!

Wat does something like this cost

Screen protector for a car??

You don’t wrap edges?

Hey I am from India I know window film and PPF I want to work on your shop because your work its to good.. reply Me for more information

I want ppf. My car with headlights done too.

@thefilmguy6497

3 жыл бұрын

head over to www.driveprotected.shop to find the PPF for your vehicle!

Untuk kekuatan bertahan berapa th

Hey I had a question what’s the bet tint to buy

@DetroitTintStudio

4 жыл бұрын

lots of good films out there, I personally use Avery Dennison right now.

@Viages

4 жыл бұрын

TintStuff what about formula one pinnacle ?

sprayer gun as you can find on amazon?

At 3:38 I heard a FART 💨 😅

Can you do a precut front windshield tint installation?

@DetroitTintStudio

4 жыл бұрын

Pre-cut kits don't hardly ever work for the windshield. I tried a number of different kinds of software and the patterns are almost always off. the sides and back are better depending on the software used.

@RaccoonSniffer

4 жыл бұрын

Is it just as easy as window tint?

Paint protection film. Lol. If your that worried buy it and look at it in the garage. Otherwise figure out Kitts paint and paint your car like that. It’s a car. Not importantly Life. And I love and have expensive cars. Just learned over time

@bradleyb5021

27 күн бұрын

What a dumb fucking comment. this helps resale value, keeps your vehicle in good condition. It's called protecting your investment, get a clue.

Thanks for the video, but “just a ZR1”… c’mon. That’s a monster of a vehicle

🙏🏼🙏🏼🙏🏼🙏🏼🙏🏼

@rukazapatrick8281

3 жыл бұрын

5000M likes

anyone heard the over lapping voice 2:08 - 2:10

put sone silicone on the edges. just a thin layer so that it wont come unpealed

Just a ZR-1?? Really slumming it, man.

@freddiecarr7602

4 жыл бұрын

If you've seen his other vids--he does a lot of tongue in cheek humor. Good dude

@beulahboi

4 жыл бұрын

As do I lol

"unfortunately its a ZR1" lol

Just use Johnson &johnson in the water to apply it and smells great

Bad install man. You should have removed and applied it correctly, unless you didn't charge your customer. You should have lined up the headlight first, with an EVEN gap. Then tacked it and moved on to your fender corner or around the side scoop. You always have to make sure that gaps are even. While it may be hard to see the uneven gap around the headlight now, it WILL show in time, as the line will build up with dirt and it will show. Next time, take your time and have patience. PPF isn't hard, but it takes time.

Did you just downplay a zr1 for a measly c8? Dude! What’s wrong with you!??

Unfortunately it's just the ZR1???? I stop watching at that point.

Just a ZR1 lol.

That is not a $120k car

DO NOT DO THIS! I did this to my car and it messed up the paint.

@netocdmx9736

2 жыл бұрын

This is a 3-5k$ job is not going to do nothing to the paint if install the correct way. You probably use a les quality film, or solution.

It's just a ZR1 hahah