I now know how to change a spindle on a scag thanks to this very helpful video. Thank you!
@joedematteo5163Ай бұрын
Right to the point explanation and video. Awesome. I've changed one spindle on our turf tiger. It did not come off so easy, was a 2002 model. We literally had to torch it off. I really hope our 2019 model comes apart that easy blade brothers!
@Brotherslawn23
29 күн бұрын
I appreciate that. I have some tricks for the old stuck spindles, I just couldn’t use them on these warranty spindles.
@LS3438Ай бұрын
Run you a small flat head on the cut of the taper lock to widen it and it’ll slide off easier . Good job 👍🏻
@brianbroerman8758Ай бұрын
Not sure if we have the same spindles but FWIW my 2022 Liberty Z had a couple spindles go bad with less than 40 hrs on the machine
@Brotherslawn23
Ай бұрын
They are aluminum non grease able. That’s sad I’m not sure what’s with scags quality control lately
@jayhaynes466823 күн бұрын
Bro that was impressive the speed and efficiency
@Brotherslawn23
22 күн бұрын
Thanks it’s been a little while since I’ve had to do one.
@jayhaynes4668
19 күн бұрын
@@Brotherslawn23 I have to do 3 myself but this has given me a little more confidence
@jayhaynes4668
19 күн бұрын
Also how many pumps of grease did you do for the new spindles
@Brotherslawn23
18 күн бұрын
@@jayhaynes4668 just nuts and bolts my friend.
@Brotherslawn23
18 күн бұрын
@@jayhaynes4668 I check the “pop off “ or over flow valve and when it starts to come out I stop.
@tccurtis293218 күн бұрын
I had to change the middle one on mine at 1200 hrs. Not as easy. That damn thing might as well been welded on.
@Brotherslawn23
17 күн бұрын
If you have a big enough air hammer get the bolts loose and drive the spindle out out of the hub, I drive the pulley off as seen in the video, but if the hub is froze to the spindle just drive the spindle through it.
Пікірлер: 15
I now know how to change a spindle on a scag thanks to this very helpful video. Thank you!
Right to the point explanation and video. Awesome. I've changed one spindle on our turf tiger. It did not come off so easy, was a 2002 model. We literally had to torch it off. I really hope our 2019 model comes apart that easy blade brothers!
@Brotherslawn23
29 күн бұрын
I appreciate that. I have some tricks for the old stuck spindles, I just couldn’t use them on these warranty spindles.
Run you a small flat head on the cut of the taper lock to widen it and it’ll slide off easier . Good job 👍🏻
Not sure if we have the same spindles but FWIW my 2022 Liberty Z had a couple spindles go bad with less than 40 hrs on the machine
@Brotherslawn23
Ай бұрын
They are aluminum non grease able. That’s sad I’m not sure what’s with scags quality control lately
Bro that was impressive the speed and efficiency
@Brotherslawn23
22 күн бұрын
Thanks it’s been a little while since I’ve had to do one.
@jayhaynes4668
19 күн бұрын
@@Brotherslawn23 I have to do 3 myself but this has given me a little more confidence
@jayhaynes4668
19 күн бұрын
Also how many pumps of grease did you do for the new spindles
@Brotherslawn23
18 күн бұрын
@@jayhaynes4668 just nuts and bolts my friend.
@Brotherslawn23
18 күн бұрын
@@jayhaynes4668 I check the “pop off “ or over flow valve and when it starts to come out I stop.
I had to change the middle one on mine at 1200 hrs. Not as easy. That damn thing might as well been welded on.
@Brotherslawn23
17 күн бұрын
If you have a big enough air hammer get the bolts loose and drive the spindle out out of the hub, I drive the pulley off as seen in the video, but if the hub is froze to the spindle just drive the spindle through it.