Got the RV 454 running on my cheap engine cradle. Seems to be in good shape. Almost don't want to take it apart. But it will be better after the build.
Жүктеу.....
Пікірлер: 55
@my357magsАй бұрын
And now the fun begins! Can't wait to see the build! 👍
@thereluctantgearhead4544
Ай бұрын
It's gonna be pretty rowdy.
@my357mags
Ай бұрын
@@thereluctantgearhead4544 Good...we like rowdy!
@thereluctantgearhead4544
Ай бұрын
@@my357mags yep, might as well utilize its real potential. I have the shit to make it a monster.
@my357mags
Ай бұрын
@@thereluctantgearhead4544 For sure!
@robertangell7926Ай бұрын
Sounds good Sam now u know what you got ! Got a couple mouse motors(70 LT1&aluminum bow tie head 350)for the run stand.Got a 400 on engine stand now .30 over new flat tops.
@travisquintero8334Ай бұрын
😂😂 neighbors love it
@thereluctantgearhead4544
Ай бұрын
Strange my fuckin comment vanished. Imagine that.
@johnzuggster375Ай бұрын
Thanks for posting, i would sure like to meet you sometime!
@infamousnovaАй бұрын
Wow, runs good
@judgegixxerАй бұрын
Stuff it in the early 3rd gen. Get that thing right twisted. That old 454 sounds pretty snappy as it is. I'm sure it will be nuts when you're done with it. Nice little test set up.
@thereluctantgearhead4544
Ай бұрын
The Camaro has a fresh built SBC that makes around 550hp or so. It's pretty rowdy. Brand new expensive ass headers too. But I'm also building a 496 bigblock Chevy with a tunnelram that'll probably go in the Camaro in a year or so. It's gonna make around 800hp NA. Gonna drop this 454 into a gutted 79 Cutlass that don't weigh shit. Manual T-400 & 5000 BTE convertor and 4-57 gear on a 35 spline spool in a QP 9 in Ford going behind it. It's pretty much a drag only car. Been sitting over 20yrs.
@judgegixxer
Ай бұрын
@@thereluctantgearhead4544 Sweet, I've had a 91' Z28 since 93' so I'm gonna have to go thru your videos to check it out. One thing for sure is NOBODY will be able to say that Cutlass is gutless.
@itseithergonnaworkoritaint7852Ай бұрын
Gotta figure out how to make those old dried up pumps work again just in case the world goes to a Mad Max era.😯😎👍
@thereluctantgearhead4544
Ай бұрын
Definitely gonna buy a diaphragm kit for the Mallory pump. It's worth fixin.
@thereluctantgearhead4544
Ай бұрын
The other electric pump was just one of those little Mr Gasket helper pumps. Not worth much. Probably made in 1980.
@itseithergonnaworkoritaint7852
Ай бұрын
@@thereluctantgearhead4544 How would you fix that pump if you couldn't buy a rebuild kit? That would be a great video series, how to build an engine with no infrastructure.😎👍
@gregleenyitАй бұрын
Hell Yeah lets make some noise
@heathvice8365Ай бұрын
Hell Yeah👌🤣
@JohnMiller-ee9pnАй бұрын
I think E 85 mechanical fuel injection maybe Crower stack turn out the beast
@thereluctantgearhead4544
Ай бұрын
That would be cool. Gold anodized stacks are the shit.
@thereluctantgearhead4544
Ай бұрын
Seen a setup a while back for $2500. Had everything to go with it.
@USA-km9phАй бұрын
What cylinder heads are you gonna run? Thanks
@thereluctantgearhead4544
Ай бұрын
Either BPE 317cc or Assault 335cc. Both rectangle port. Going to use a DART singleplane or a Super Victor and a BG 1050 Dominator.
I already have all the parts. Just gotta make it happen now.
@pauldhiman8369Ай бұрын
Summoning satan 😈✊🏽
@Saan455Ай бұрын
Peanut ports heads ?
@thereluctantgearhead4544
Ай бұрын
Yep, 236 castings. But they are going on a shelf. Low mile units, probably sell them. Too small for my plans. It's a 1981 Motorhome 454 straight out of the RV. Been sitting for decades. I'm just gonna use the bare block.
@Saan455
Ай бұрын
@@thereluctantgearhead4544 If I have the money and time I would build 427 truck block 4.375 stroke and peanut ports to go in k30 crew cab tow rig and max rpm will not go above 5k. 4l85e np205 14b d60. My dream truck. Anyway your biggest from KSA
@thereluctantgearhead4544
Ай бұрын
@@Saan455Be good for a tow rig for sure. Those tall deck 427s were stout. I'm building one with long rods and lightweight forged pistons and a huge solid roller cam. It's gonna be a drag race engine tho. Came out of a GMC 7000 dump truck. Block is extra thick.
@thereluctantgearhead4544
Ай бұрын
@@Saan455I'm using a 4.310 bore & 3.76 stroke on the tall deck. Gonna turn it high RPMs.
@Saan455
Ай бұрын
@@thereluctantgearhead4544 3.76 is a spinner . If you are not going to run over 7k just go 4in stroke and make it 468 cu
Пікірлер: 55
And now the fun begins! Can't wait to see the build! 👍
@thereluctantgearhead4544
Ай бұрын
It's gonna be pretty rowdy.
@my357mags
Ай бұрын
@@thereluctantgearhead4544 Good...we like rowdy!
@thereluctantgearhead4544
Ай бұрын
@@my357mags yep, might as well utilize its real potential. I have the shit to make it a monster.
@my357mags
Ай бұрын
@@thereluctantgearhead4544 For sure!
Sounds good Sam now u know what you got ! Got a couple mouse motors(70 LT1&aluminum bow tie head 350)for the run stand.Got a 400 on engine stand now .30 over new flat tops.
😂😂 neighbors love it
@thereluctantgearhead4544
Ай бұрын
Strange my fuckin comment vanished. Imagine that.
Thanks for posting, i would sure like to meet you sometime!
Wow, runs good
Stuff it in the early 3rd gen. Get that thing right twisted. That old 454 sounds pretty snappy as it is. I'm sure it will be nuts when you're done with it. Nice little test set up.
@thereluctantgearhead4544
Ай бұрын
The Camaro has a fresh built SBC that makes around 550hp or so. It's pretty rowdy. Brand new expensive ass headers too. But I'm also building a 496 bigblock Chevy with a tunnelram that'll probably go in the Camaro in a year or so. It's gonna make around 800hp NA. Gonna drop this 454 into a gutted 79 Cutlass that don't weigh shit. Manual T-400 & 5000 BTE convertor and 4-57 gear on a 35 spline spool in a QP 9 in Ford going behind it. It's pretty much a drag only car. Been sitting over 20yrs.
@judgegixxer
Ай бұрын
@@thereluctantgearhead4544 Sweet, I've had a 91' Z28 since 93' so I'm gonna have to go thru your videos to check it out. One thing for sure is NOBODY will be able to say that Cutlass is gutless.
Gotta figure out how to make those old dried up pumps work again just in case the world goes to a Mad Max era.😯😎👍
@thereluctantgearhead4544
Ай бұрын
Definitely gonna buy a diaphragm kit for the Mallory pump. It's worth fixin.
@thereluctantgearhead4544
Ай бұрын
The other electric pump was just one of those little Mr Gasket helper pumps. Not worth much. Probably made in 1980.
@itseithergonnaworkoritaint7852
Ай бұрын
@@thereluctantgearhead4544 How would you fix that pump if you couldn't buy a rebuild kit? That would be a great video series, how to build an engine with no infrastructure.😎👍
Hell Yeah lets make some noise
Hell Yeah👌🤣
I think E 85 mechanical fuel injection maybe Crower stack turn out the beast
@thereluctantgearhead4544
Ай бұрын
That would be cool. Gold anodized stacks are the shit.
@thereluctantgearhead4544
Ай бұрын
Seen a setup a while back for $2500. Had everything to go with it.
What cylinder heads are you gonna run? Thanks
@thereluctantgearhead4544
Ай бұрын
Either BPE 317cc or Assault 335cc. Both rectangle port. Going to use a DART singleplane or a Super Victor and a BG 1050 Dominator.
@thereluctantgearhead4544
Ай бұрын
Cam is actually 272/280@.050, 731/731 lift, 110 lobe separation solid roller. Lunati grind. Crane roller lifters.
@thereluctantgearhead4544
Ай бұрын
13.2-1 Compression.
@thereluctantgearhead4544
Ай бұрын
I already have all the parts. Just gotta make it happen now.
Summoning satan 😈✊🏽
Peanut ports heads ?
@thereluctantgearhead4544
Ай бұрын
Yep, 236 castings. But they are going on a shelf. Low mile units, probably sell them. Too small for my plans. It's a 1981 Motorhome 454 straight out of the RV. Been sitting for decades. I'm just gonna use the bare block.
@Saan455
Ай бұрын
@@thereluctantgearhead4544 If I have the money and time I would build 427 truck block 4.375 stroke and peanut ports to go in k30 crew cab tow rig and max rpm will not go above 5k. 4l85e np205 14b d60. My dream truck. Anyway your biggest from KSA
@thereluctantgearhead4544
Ай бұрын
@@Saan455Be good for a tow rig for sure. Those tall deck 427s were stout. I'm building one with long rods and lightweight forged pistons and a huge solid roller cam. It's gonna be a drag race engine tho. Came out of a GMC 7000 dump truck. Block is extra thick.
@thereluctantgearhead4544
Ай бұрын
@@Saan455I'm using a 4.310 bore & 3.76 stroke on the tall deck. Gonna turn it high RPMs.
@Saan455
Ай бұрын
@@thereluctantgearhead4544 3.76 is a spinner . If you are not going to run over 7k just go 4in stroke and make it 468 cu
455 5/7/24
@thereluctantgearhead4544
Ай бұрын
743 on 5/9/24
@thereluctantgearhead4544
Ай бұрын
802 on 5/12/24
@thereluctantgearhead4544
Ай бұрын
812 on 5/14/24
@thereluctantgearhead4544
Ай бұрын
831 on 5/16/24
@thereluctantgearhead4544
Ай бұрын
835 on 5/18/24