4AGE road bearings: amzn.to/2nRJ9p2 4AGE main bearings: amzn.to/32oJsqw 4AGE complete kit - rod bearings + main bearings + thrust washer: amzn.to/2IXS1Rq Let's hang out: superpeer.com/driving4answers

You did exactly what I want to do at the end of your video. 2 weeks of hard work on the top end to hear a knock after start up. I had an oiling issue with my new oil pump. Sick is an understatement. Thank you for reminding me it isn't the end of the world, just a lesson. Painful one, but a lesson. Thanks for the video!

I like this guy’s sense of humor 😂

@isaacchamings8473

3 жыл бұрын

I realised it wasn’t the video I was looking for but it was too funny to stop watching 😂

@Bluenosedogman

3 жыл бұрын

European comedy LOL. I love how he laid out the cloth at the end

@BaveMage

2 жыл бұрын

His son should apply to Starfleet Academy in a few years!

You’re honest humble attitude followed by a humorous harakiri is a perfect example of the experience that goes through a drivers mind when they understand how serious/expensive/work intensive it’s going to be bring back their dream project/baby/daily driver back to reliable running condition. ( The AUTHENTIC shot where you’re pulling the oil pan and demonstrating how well the OEM GASKET functioned, was just beautiful!)

First step is to cry a little.

@d4a

6 жыл бұрын

ShazamMafia Haha true.

@carloscrod_

4 жыл бұрын

🤣

@lundonx116

4 жыл бұрын

i cried a lot bc i just got the truck 4 months ago 😭

@tiemze

3 жыл бұрын

a little or a lot its all ok

@vladnickul

3 жыл бұрын

Just wait till you guys have a impreza. its inevitable

“that hammer was to weak so I grabbed an axe” . Almost about pissed myself 😂😂😂

@kwbalance108

4 жыл бұрын

LMAO!!!

Don't be fooled. That ax and pirate knife are professional tools from the Snap-On truck. $400 each.

@d4a

6 жыл бұрын

Special Ed lol!

@coolramone

Жыл бұрын

$600 with Biden inflation.

Good to hear that you are using this unfortunate situation as an opportunity to improve your MR2. I am looking forward to more videos in the future.

@d4a

7 жыл бұрын

aztecred92 Thank you for your support. I'm fortunate to have you on board.

Great detective work. No BS video. Loved it. Been there on my back removing oil pans. Thanks.

pro tip, tap on the bottom of the rod cap while the piston is at the top of its stroke, you'll hear which of the rods are loose.

I wish more videos were like this. No nonsense, right to the point

Torque wrench seppuku was the best ending to any video I've ever seen. XD

@d4a

7 жыл бұрын

+802 Garage Hehehe. Thank you. I guess I can cross that one off on my bucket list.

@TooManyChoices1

5 жыл бұрын

802 Garage Needed his buddy to come behind him and smack him over the head with a monkey wrench after, but bravo for the attempt 😂👏!

@Barrenchats

4 жыл бұрын

No no no you use a inch-lb torque wrench you're second uses a ft- lb torque, well maybe in you're next life "engine failure".

I had a '66 Jeep Wagoneer with an AMC 327 V8 engine. It ran quiet, but smoked some. I was going to replace the rings, but when I removed the rod bearing caps, I saw that the bearings were worn down to the copper. I checked the journals with a micrometer, and they were in surprisingly good condition. I replaced the rod and main bearings, along with the rings, and a few other things, and it ran great. All I'm saying is that I'd check the crank first. You may be able to polish the crank in the engine and use a slight oversized bearing, and get a good engine.

Thanks for the detailed look inside! I"m having some heavy knock in my '85 MR2. I haven't cracked it open yet but it shows all the signs of bottom-end bearing failure. I've juiced it with 20w-50 and we'll see how it goes a few miles at a time. I plan on a swap or rebuild. Look forward to more of your videos, and hope to have a few of my own up soon. Take care!

@d4a

7 жыл бұрын

+bee dee Sorry to hear you got the knocky rods too. 20w50 won't help much or for long. I would suggest getting the engine out asap, before it throws a rod and makes a huge mess of your engine bay. That would also mean you will need a new block. If you're determined to do a swap than it matters less, but still best to get it out soon. I'll be uploading an engine drop video next week, should be useful for you. Good luck and let us know once you upload your vids, I would love to see them. Thanks for watching.

Great info! That helped me a lot. Tough luck on the engine!! I'm sure the new rebuild will be awesome. By the way, I think I would of did the same at the end. Lol. Can't help but to like the improvising tools. Keep up the good work.

Great video!! im doing the same with my CItroen 3cv (Argentine version of 2cv6) when i see the rock knock... is only the half the other parts in the bottom of the engine block... the engine was running fine ...is a 1974 model... never open the engine... very good quality engine ......

You didn't even scream at the end. Very honorable. :)

Thanks for the rod bearing education.

2:46...Smelling your bolt is very important when it comes to changing oul.

This is perfect! im thinking of buying the same generation mr2 and the one im looking at has rod knock. Thanks!

Thanks, this answered everything I was thinking about with my car. Next step, just pull the crank caps and inspect. Nice humor, and decent video.

I feel for you brother! That's just the nature of cars, I wish you the best on the guts transplant and would highly advise a quality oil pump over something like a turbo, keep your chin up bro!

@d4a

7 жыл бұрын

Hey there. Thank you for your support man! I bought a brand new AISIN oil pump the first time I was doing this rebuild. I will see if it can be reused, it only did like 600 miles. But I will buy a new one if there's any hint of something wrong with this one.

@BWeezy-sw1wy

4 жыл бұрын

Good reply Road Worthy. Also i think the point of the attack is not the gutsbas much as the main arteries feeding and returning to the lower part of the body.

@great4ever845

Жыл бұрын

Can't you just replace bearings ?

Lol that ending was great!!!! Love your sense of humor

first half of video is funny as hell man thanks for the great video

The insensored parts are GREAT because working on cars is not always textbook, sometimes u got to improvise adapt and overcome!! Great job keeping it real tho!!

@d4a

6 жыл бұрын

Victor Ramirez You said it!

Miss the retractable headlights from the 80s-90s. Had a 1985 GT Celica and wish I would of kept it. Great power and good of fuel...Looks like I'll be doing this work on my 97 Camry including the Pirate knife...

Actually, I would replace the crankshaft, because I saw heat damage from the friction, meaning that the crankshaft probably has lost some hardness at the journals. However, getting a junkyard engine is probably cheaper, so repearong this one, and getting a junkyard engine if this one fails is also a good option

I think I remember from the Road Hunt Episode you telling about some wrong procedure on sodablasting inner engine parts... Maybe it was suspension issues. Not so sure, but I heart it from you.

My 03 mercury has the same problem and thanks for the info

Fantastic video mate :)

Online diagnosis is always difficult an d more like poking in the dark, than serious problem solving. Plus, I know Volkswagen EA827s but not Toyota A-engines. Like you said in the video, the damage can be caused by a weak oil supply, due to a worn out pump, bad/wrong filter, or dirt inside the oil galleries. Do you flushed and brushed the galleries, when you rebiult the engine? The rod bearings get less oil than the mains, so they die first on not enougth oil or low pressure. Dirt inside the galleries first goes into the main bearings and grindes them before the rod bearings. Unplausible according to the footage, but i woul check them. You will have to pull the crank out anyway. Different Idea: Of course the crankshaft could have been already damaged or bent when you assambled the motor. Do you checkt it for balance and messured the exact journal diameter? And what size of bearings do you used? Maybe the journals were already grinded once before and standard sized bearings caused way to much bearing play --> more oil loss at the bearings --> less oil pressure + big bearing play -----> damaged bearings. Used Parts are cheap an especially on old cars the only available ones. But you never know, what happend to the stuff before. Little tip at the end: Put some cardbord on the floor, when you work under the car. It´s way more easy to slide around on it and less cold in winter.

Your intro is the best dude 😍🤣

Great video!

Pirate knife and an Axe, apparently the true tools of a professional, don't forget the seppuku torque wrench, which is the step I'm current at with my 4runner.

Very artistic oil pan paint job.

@d4a

4 жыл бұрын

I'm an artist at heart lol

The crank journals need to me measured and tested very very precisely. I'd say while you have it out, test the runout on the crank, taper and out of round on the crank and rod journals, and basically see if your crankshaft is worth a shit before you move on. Also, plastigauge the journals just to make sure that you have good oil clearances. Great build though, I just subbed to your channel about a month ago and love the content

@d4a

6 жыл бұрын

Dominic Iacino Thanks, will measure everything as I did first time. The problem turned out to be blasting media that got inside the engine somehow. I made a small update video about it. My crank is in the machine shop already, getting ground 0.25 mm. :)

Thanks! Very helpful!

Great vid!!!

Love the snap-on kitchen knife! lol

Very good video

i love your videos and what you do what you explain keep up good work! Greetings from Turkey!

@d4a

7 жыл бұрын

Mustafa Usta Thank you! I'm happy to have you on board. Turkiye cok guzel :)

@Mstfstable

7 жыл бұрын

teşekkürler :) have you been in Turkey

@d4a

7 жыл бұрын

Mustafa Usta Bursa, Izmir and Ankara a loooong time ago. Istanbul 2 years ago.

@Mstfstable

7 жыл бұрын

Very nice i live in Kayseri i have been in Ankara and İstanbul too, very nice cities i am looking forward to see your new videos

@gregoryfuller1136

5 жыл бұрын

A guy named Mustafa from Turkey!!??? Crazy! What are the chances??

Good video!

Nice video sir.

Brilliant vid this stuff happens to me specially the exuast in the hoodie keep the faith man

Like the choice of tools

thanks for all information

I spun a rod bearing and the conrod had elongated into an oval on my turbo engine. With the engine in the car and without removing the crank, I was able to sand down the main and rod journals, and change all the main and rod bearings. Obviously the damage was much worse than yours. I debated buying a new conrod but didn't want to have to remove the entire top end to pull the pistons so I decided to shim the conrod cap with a piece of soda can (just a shim on the bottom not the top) and used standard size bearings everywhere including that one conrod. I had debated whether to use one standard and one +1 oversize bearing on that one conrod but I'm glad I used the shim now. I checked all clearances with plastigauge. It runs great has good oil pressure (70 cold and 35 hot). I babied the car for the first couple hundred miles, changed the oil and since then have been driving it hard as normal. It's been about 6 months since the repair and runs great. All that to say, don't give up you can fix these type of problems without rebuilding the entire engine.

@adik9441

8 ай бұрын

Shimming doesn't work always

polish the crank and install new bearings

@fflynnful

2 жыл бұрын

Should the replacement bearings be the next size down?

@chriscusick6890

2 жыл бұрын

Depends on bearing clearance ascertained by plastigauge or micrometer.

@chriscusick6890

2 жыл бұрын

You could but risk excessive clearance thus lower oil pressure. Engine should be thoroughly cleaned of all metallic particles before new bearings are installed.

I know the feeling😢 just happened to me with my is300 2jz😢😢😢 i have limited space to take the engine out through the top/with a crane..... ill try through the bottom😅 not giving up! Cheers to you and your knowledge! 🍻

Subscribed for the opening music.

Have to agree with 802 Garage seppuku was a good conclusion and well done :-)

Funny ending and helpful/ good video

My first car was an '86 MR2. There are currently 4 mk1s sitting in my dad's yard. Working underneath was always a pain. I pulled the fuel pump one time and socked myself in the eye with the drill battery. Knocked it off a jack and onto a wheel I had slid under it while changing out the alternator. I quit for the day after that happened. Just about pooped my pants. Timing belt? OMG what a pain. I pulled the engine and transmission when I was 19 and had the block and head work done by a shop for $900. I reinstalled it myself. Priming the coolant in Mister two is a real PITA. The 4AGE is a real fun motor to rev though. They used it in the Toyota Atlantic series back in the day. Putting it in the MR2 was brilliant, but also a mechanic's nightmare. Toyota at the time was way more practical than fun and the AE86, MR2, and supra were big shifts for Toyota in the 1980s.

@d4a

4 жыл бұрын

You're a proper adub veteran my man! Much love for that. You're right, the space in that engine bay can be tight but it's still an absolute joy and breeze compared to newer cars.

Keep a knocking, but you can't come in! Rod: what you mean, I'm trying to get out!

The ending was the best part lol

Lol mechanic acrobatics😭😭😭🔥🔥🔥🔥lol You the 🐐

Thank you very imformative

I worked at an engine re-man facility and i did the crankshaft recondition and set up in block. Bottom end work should be done with the engine out of car. IF you really know your work and its an easy engine to access, a bottom end refresh is possible. I would not recommend this for a shade tree tech. The total run out on a v8 crank is .0002. The taper on a rod journal can be as tight as .000015. There is no mention of a crank knock ( crank main journal moving in a main bearing) which is not common, but happens, and it sounds like a rod knock and many times it is acceptable and doesn't affect engine life.

I have the same looking bearings on my 4.0 i just need to drive it across the border for 15 min do you think if i put new rod bearings ill make it

What your setting tork you using bro ..look nice way to ending..

I enjoyed your VDO

@d4a

6 жыл бұрын

I get it....Vi Di Ou....Good one!

It real help me and save a lot in my pocket.

Did you use more oil to account the volume of oil that is flowing into the oil cooler?

Great intro

Exelent información thanks 👍

Something got very hot.I recommend a high silicon aluminum bearings as they are durable and the will polish the journals.

I sympathize with you cause I think I got same problem 2002 BMW x5... Looking for a knife now ..

This was awesome.. not only educational.. but silly as shit. I gave it a like brother .

The answer is 4A-GE 20V Blacktop! 👍😊

@d4a

7 жыл бұрын

Hmmmm, that's never a bad idea. But I would need to import that engine, which is a horribly complicated and extremely expensive endeavor over here in Europe. I would love to hear that sweet ITB sound tho.

@joshcallaghan9432

6 жыл бұрын

Yeah I agree, I had a silver top in mine and they are just the best engine!

Hey man love the videos. Also sorry about your engine, it totally sucks that you did everything right and still get that outcome. Hope you're able to get something else sorted without too much hassle. Pity it's so difficult to get a blacktop in your location. There's plenty around in NZ and you can pick them up for as little as $400. Anyway, keep up the good work with the vids.

@d4a

7 жыл бұрын

Don't Fall For Me Thanks a lot man. Your support means a lot. I am seriously considering emigrating to NZ, the 4age scene and the car scene on general seems really awesome over there :) Europe is seriously weak in the 4age department, but I guess that makes me kinda exotic and special? Who knows. Maybe I come over some day :)

@hajrudinkavazovic2231

Жыл бұрын

​@@d4a no sikiriki drug sve se napravi samo zdravlje malo teze 😊 🤟

How many miles on original engine when pulled out. How often do you change the oil, what weight are you using??

Use emery cloth and polish the journals then roll in a new set of bearings. Do this to big deisel engines and works every time.

@darrynleslielees1111

Жыл бұрын

Awesome will try this

Was it loud and did it got louder when you give it gas too mine gets louder when I give gas and when I turn the ac on and when I turn the steering wheel too I don't know if the bearings are bad I did the compressor test and it seems to be healthy but it's making knocking noise

Lol!! Pirate knife, im adding that to my tool box today, and im going to the reservation to get an official tomahawk !!! Sorry about your discovery, but I know of no one more capable and knowledgeable of the “project engine removal” than you. Take us with you! That little rice burner is going to be a rice rocket! It’s gona be the baddest go-cart on the intraWeb! Keep smelling bro, the nose knows.

You did the honorable thing.

I've seen people laugh when they see a rod poking out from the block. Everyone knows it's now a boat anchor, and the owner was almost proud of the carnage. But when people hear that knocking sound, a pall falls over the group and no one wants to be the one to say it first. The optimist will always say, "maybe it's a collapsed lifter", even knowing it's a solid lifter engine.

The head part kill me 😂😂😂😂😂 nice vid as always

That crankshaft is not so bad, I'd just put new bearing shells and see what happens.

Nice video thank u

what if you get a new crank shaft and bearings for it you can save the engine right?

You can explain the symptoms? The knock is loud when the engine are warm or cold?

My god that was funny, I needed that right now, the end of your video is how I feel right now, i just spent $1,100 on OEM parts timing chain, gaskets, oil pump and oil pan gasket, 16 lifters and the hours to install them. The knocking got even worse, the bad thing was I could not get the oil pan off to look at the rod bearings. I really do think it's probably rod knock, so I'm going out tomorrow to buy a car for the wife spending $11,000 to $17,000 on a car and park this pig 2001 Dodge Dakota with 200k mileage and figure what I'm going to do, I was thinking of buying a used engine $800 to $1,500 and swapping out the parts witch would put me at $1,800 -$2,500. not sure if that's the right decision the problem with that is I can by a long block for $2,800 and have a 3 year warranty on the engine. Sometimes its best not to be handy, in retrospect I should have parked the truck, bought a another car and pulled the engine I would have saved my self $1,1000 and 15-25 hours. This truck turned into a money pit.

@d4a

6 жыл бұрын

Naaaah. I thought that way for a few days after it happened to me to. I wanted to burn the car down. But the learning experience was valuable. I did the rebuild twice as fast the second time around :) Try to be positive about it, in the long run it will all make sense. Right now just park it and let things settle in your head :) The right decision will come by itself.

This is a great video. Thank you so much! I laughed the entire way too! Grabbing the axe and the pirate knife hahaha! Whatever works! What kind of tool do you use to turn the engine? I hope you got your MR2 working-I know that sucks

@d4a

5 жыл бұрын

Mr2 is definitely back in action. You can check out some of the new vids to see how I rebuilt it. I use a Socket wrench, a very long extension and a 17mm socket to turn the engine. Works great.

did you replace the oil pump when you did the rebuild? sadly it's a part that often gets overlooked

@d4a

7 жыл бұрын

Lmenzol Replaced oil pump, even primed the gears with assembly lube. Replaced water pump too.

How did everything work out?

First seconds of the video, I thought the solution to all 4 rods knocking was to just turn the radio up. To be fair, that did work when I had rod knock

Lol your samurai ending 😂😂😂

Is there a trick when putting the rod bearings back on?

At some point this just became everything you shouldnt do under a car lmao lmao.. good vid

Yep try a 4 wheel drive oil pan removal on a gm blazer. Some major engineer hates mechanics for sure the way it is designed.

Same thing just happened to my BUILT 350z motor. The person that rebuilt it left an oil leak somewhere and I've been putting oil since rebuilt. I went 1 week without adding oil and just killed it last night

just sand the journals and put in new rod bearings

@pornokid333

3 жыл бұрын

uh. naw. this isnt a tractor its an 8000rpm motor

@WizzRacing

3 жыл бұрын

@@pornokid333 Horse shit..I done it to 500 hp+ engines..Unless they are scorched earth burned to shit. You can polish them out..Slap some new bearings in. She be good as new...

@glenquagmire4232

2 жыл бұрын

As long the tip of your nails does not feel a scratchy feel on journal it is safe to say that all you need is to polish that journal

It's me Rodney!

You should of used plastigage to check clearence between new bearing and crankshaft. Should be somewhere around .002 In. Or slightly less. If needed, use oversize bearing to compensate. Make it a little on the tight side, so bearing can wear in. This may keep you from replacing crank or engine. Check other bearings.

@balkantvofficial

2 жыл бұрын

i need you help on ths one because my hyundai genesis is making a crazy noise under the car i would like to get in touch with you on facebook and show you the video ifpossible because i dont want to shange the complete engine can u help

@RingstedHedge

2 жыл бұрын

No such thing as a bearing wearing in. The crank and bearing should never touch, needs oil films always no exception.

Hi i think my car has rod knocking sound Mazda 6 2.0 2003, do you think i need to fix this rod bearing or just wait it to explode

Lol 🤣😂😂😂. Because you are sooo funny, I subscribed! Haha!

Hammering a pirate knife into an oil pan with a hatchet... This is a man I would pay to work on my MR2! Hahaha.

@yourstruly265

6 жыл бұрын

try ice pick, hammer with a kilo sledge hammer...!

@matteightytwo

6 жыл бұрын

This exactly what I was going to post.. the man wanted to get the job done

@PlanetVyctory

4 жыл бұрын

Next time just try a flat head screwdriver? Will pry, won't break.

The rods should have zero movement correct? I haver a bad bearing and I can wiggly the piston rod, from the bottom, back and forth 1/16" to 1/8"....this means I have a bad bearing on that piston, correct?

i like the oil pan paint job lol

Thanks