Excellent testing and review, as always! Thank you so much!

@robojax

5 жыл бұрын

You are welcome. I am glad you liked it.

@Try_to_success

4 жыл бұрын

@@robojax 60M PWM Speed ​​Control Circuit hello, can I ask you a bit, can this circuit be used for 2 motor slowdown 24v 250W 14A .. I hope you can help

Your insight is very admirable. Thankbyou

Fantastic video production really enjoy your knowledge base I wonder if you might be able to test the roboclaw 2x30 because I really wonder about continuous use reliability over a regular basis

Nice test, thanks a lot.

Thank you very much for this. I just bought two of these. One with 60 amp output and an LED power meter and one with a max of 40 amps. You have helped me understand much more about this controller. I will check the mosfets for anomalous heat patterns and add a cooling fan. I am glad to find out it already has current limit built in. Do you have a video for troubleshooting these controllers? I suspect the relays are not robust enough. Both of my controllers have 2 relays.

@robojax

5 жыл бұрын

You are welcome. I am glad you found my video helpful I don't have a video, but 2 thing will make them bad. first revers polarity of power and the second, overheating. in both cases mosfets will get damaged and I believe other components should not get damaged.

brilliant

very good! actually I'm new to these stuffs and still learning but every circuit I saw was with a single mosfet so I was wonder if the pre assembled pwm controllers using mosfets in parallel or series and why multi transistors or what are the other components. so you helped me out to get a little out of the confuse. that is nice also seeing you responsing and answer the comments

@robojax

3 жыл бұрын

I am glad you found it useful. Greeting from Ahmad from Canada.

Muchas gracias por el video.

THANK YOU for detailing every component on this board so that I can understand its purpose! I just bought this board to control my custom made electromagnet using my Arduino board! If that's not a good use for this board for whatever reason, please let me know! I'll just being supplying about 3 amps @ 10 volts to my electromagnet using a 26 gauge magnetic wire.

@robojax

3 жыл бұрын

if you need 3A module then this is waste of resources and it is big. see this module kzread.info/dash/bejne/d5WkspZ7mM-_kpM.html

Thank you

@robojax

Жыл бұрын

You're welcome

Great video and thank you for sharing! Could you please do a video showing how to mod to enable forward and reverse control of dc motor using his module? I'm planning to use this to control a trolling motor for use with a kayak. Thank you!

@robojax

3 жыл бұрын

I have make a hack to control this using Arduino. But I will look at it. it wont' be easy to hack it but I try.

@chrisdelapena1123

3 жыл бұрын

@@robojax Thank you! Looking forward to it. That is the one of the things that i think is lacking on this PWM in addition to a display of the power level.

@rickbro5949

2 жыл бұрын

I think all u need are two 5 pin automotive relays and a 3 position switch for forward off reverse. I don’t know if u need diodes on the coil circuit for back emf.Seen a similar set up on a wiper motor down rigger using a pwm with automotive relays to control direction. Many dc motor reverse direction circuits using automotive relays on utube.

Nice one sir

Great video. Thank you. I noticed the potentiometers on these contain 5 wires. what do the 2 separate red/black wire do? are they just on/off? I'd like to use a 3 wire twist throttle with this and am curious how I would wire it. any help would be appreciated

@robojax

3 жыл бұрын

thanks. I just watch the video making sure I haven't missed anything and indeed I did not. I have explained it. please watch the video without skipping.

@2far2c28

3 жыл бұрын

@@robojax Thanks Robojax. Perhaps I should have worded my question differently. I understood that the red wires were switch wires but I was unsure if you could simply use a jumper on them or possibly a toggle switch. My apologies. I did receive the unit and a simple jumper works for the switch part. But what I noticed testing the potentiometer is that the voltage is full at the off position and drops as you increase the gain. That was counterintuitive to me. After some fiddling, I swapped my throttle +5v and ground cables around and can confirm that it works, however once the jumper is in place, the motor turns slowly at zero throttle, and I believe it will not reach full speed at full throttle. My only guess is that ebike throttles are outputting 1 to 4v and not 0 to 5v like the potentiometer is outputting. and I believe its a hall effect sensor in these throttles. I wish I could use the throttle I had but I'm thinking I will need to source a throttle with a different output.

@TheYockfu

3 жыл бұрын

Alex Fagundes Hello, did you ever figure out code changes to use the hall sensor (ebike throttle) in place of the potentiometer? I’m having the same issue with a similar circuit where zero throttle turns the motors.

@2far2c28

3 жыл бұрын

TheYockfu There is no code that can be changed or settings that can be updated in this controller. No one else seems to have an answer to this problem either. I’m not that experienced in electronics to have a great fix. Option one is to use a regular cable throttle that attaches to a pot and some kind of spring setup used to return the throttle lever to off (just as if it were connected to a carb). Option 2 would be to make a small module that attaches to the hall throttle and pulls down the .8 low side to 0, and pulls up the 4.2v high side to 5v. I have no idea how to build an opamp circuit for this but I wish someone could show us. It would be very handy for a diy video.

Great video. What would I need between the controller and a residential 110V AC 15amp source? Would a bridge rectifier be sufficient?

@robojax

4 жыл бұрын

Thank you. No. Your DC motor has Operating voltage. So you need to have DC power supply that matches your DC voltage of your motor. Say your motor is 24V, with 10A so you need a power supply that outputs 24V with 10A current. Now this power supply can get power from 110V (or 220V). So you need this power supply between 110V and this module.

@christianroessler9928

4 жыл бұрын

Robojax ok, thanks for clearing that up. What about using a 110V to 24V transformer between the AC power source and the motor controller? Would that work?

@oneeyemonster3262

4 жыл бұрын

@@christianroessler9928 Just get an DC to AC power convertor. ( I guess you can open it up)...yes theres some sort of raticfier going.... but to make it easy on ya. ( 2500watt converter is only $30) There's cooling fans in it....ect. This way you can just use a skil saw motor on a go kart...ect But you're going to have to pump crap load of juice through it and batteries will HEAT UP..if they dont have the cranking power or higher discharge rate. You want Magnets DC motors....brushed or brushless... so you dont need to charge the rotor to magnetize the rotor...WASTE electrticity...becuase you're not hooked to the grid any more. Batteries are either BULKY or EXPENSIVE. Power to wieght ratio..will play a factor..Lead acid are heavy..requires longer recharging time...ect Li on arnt that cheap..plus they only have 30 C....Lipo 50-100C are expensive and requires charging managment.. 15C lipo...wont be with a fu$K....They'll get HOT You;ll simply want magnets DC motors...to simply increase RUN TIME or RANGE.. hmmmmm video of dudes making heavy arsss FRam gokarts are ROOKIES..they build BRICKS...okay He's babying that tread mill motor...I'd run 48 V or at least 36V... If you some research....cross part # or know what type of transitors You can upgrade to CERAMIC or higher temp transitors...or get some with highter voltage ratings..... Samething with the diodes...fro the motor's kick back

@houseoquinnizyodaddy

4 жыл бұрын

I really like your videos. I have a treadmill motor I'm trying to use one of these boards to control it. I saw in your comments earlier you dont need a bridge rectifier after the motor because the motor outputs DC current but the volt/wattage on this motor is kind of weird. Its 21.4 amps and 95 VDC, which is maybe Voltage duty cycle? What size controller would I need in that case? Can you up size or do they have to match?

Great thanks.

@robojax

4 жыл бұрын

You are welcome.

Do you have any idea if the knob control can be somehow replaced by a pwm input signal? I don't understand where the analog knob voltage is changed to digital on the circuit board, but have one of these and want to run two fuel pumps with it. They only require a total of 40amps when at maximum pressure, so this controller should easily run them. I'm just trying to find a way to connect the pwm signal from my computer to this device. Thanks for the videos and for any help. Have a good day.

@robojax

3 жыл бұрын

here I have it kzread.info/dash/bejne/nWVny7amprPahbg.html and more like this for smaller modules

if you wanted even higher amp capabilities what would you recommenced? just more cooling or could a guy add another board or row of mosfet?

@robojax

5 жыл бұрын

I have included the datasheet in the description and you see that each mosfet can handle 90A. If you are able to attached a heat sink that is large enough with cooling, you should get 50A each which would be 50x8=400A but in theory you should be able to get 90x8=720A. I am being conservative, suggesting 400A. Read the datasheet and provide adequate heat sink and you should get that current.

@kordhassan

3 жыл бұрын

@@robojax the max ampere you got was 40 for the 7 mosfet, so you are capable to draw around 6 Amp for each mosfet

Would it be ok to spray a thick layer of circuit board lacquer on a board like this? Wan't to keep good cooling, but need some protection for random water drops.

@robojax

5 жыл бұрын

I am not sure about the conductivity of the material. Test it another board and after it dried, try to measure the resistance of two points about 2mm apart. If you get anything less than 1MΩ then you can't use it. This board has MOSFET and it is possible that the material leak some voltage and it turns it ON or OFF. So for that reason you gotta test it or read the technical details of the material before using it.

@Maxxifull

5 жыл бұрын

Ok, thanks for the reply. I will check it before using it.

so can I scratch the circuit off the 555 timer like you did on the PWM controller using the LED display screen for status and adjustments?

@robojax

Жыл бұрын

See links in description or search my channel

great video! what would happen if I connected a 12V battery to the Output of the PWM, while the Input is also connected to the same 12V battery?

@robojax

3 жыл бұрын

you will create short circuit because PWM will become HIGH (12V) and LOW (0) so it should create short circuit and burn the mosfets or fuse.

AMIGO TENGO ENTENDIDO QUE A MAYOR VOLTAGE ESAS PLACAS PUEDEN MANEJAR MAYOR AMPERAJE

I think the IC near the 555 timers in an Voltage regulatory for the timers since it is 555 timer can only take upto 15v

@thokankit007

4 жыл бұрын

And really it was a great help. Telling us each component and their data.

@robojax

4 жыл бұрын

I am glad you liked it.

I mounted a 12v battery on the pawer terminal it gives me the same voltage on the terminal that goes to the motors

great tutorial. Can we use this PWM in HHO system?

@robojax

3 жыл бұрын

I have no experience with that. sorry.

From where I can purchase this module.... Give me the link / contact information of vender... I want to purchase this module. ...

Good idea

@robojax

5 жыл бұрын

Yep

Hello, good morning, greetings from Colombia. I have a question. Same motor that you are using but with a PWM module 60v 20a 1200w in battery it works at maximum rpm but when putting weight on the motor it does not rotate and the PWM module overheats and I have it working with a chain reducer motor 🤷🏼

@robojax

2 жыл бұрын

Hello, the motor must rotate or else all energy is converted to heat, it seems motor can’t handle the load. Either reduce the load or use more powerful motor

Is there some built in current limit protection? If not how should it be protected?

@robojax

4 жыл бұрын

No. it does not detects the current.

if i understand right . ghe input voltage is the same as outpot voltage. ?. is there a card that can handle 100v DC. for trandmill motor?

@robojax

2 жыл бұрын

first part yes. here is one 1000W on s.click.aliexpress.com/e/_AMr0QD where it has tones of options like speed, brake etc but it might be useful to you.

What would be the maximum current at 24v that it can carry? 60ah? You tried 20ah. How can i make two way controller from this? This is one way controller

Did the amplitude of the motor voltage remains constant or change as the speed change. I have the same PWM board like your, I measured the voltage across the motor is changing between 2 to 11.5VDC on 12VDC input as I changed the speed control knob. Is my PWM board not function correctly?The article I read (the amplitude of the motor voltage remains constant so the motor is always at full strength. The result is that the motor can be rotated much more slowly without it stalling. So how can we produce a pulse width modulation signal to control the motor). Would you explain. Thanks.

@victorreppeto7050

5 жыл бұрын

The schotkey provide protection from flyback voltage from the motor. The tradeoff is there is a certain amount of voltage drop. Increase the size of the battery pack by one cell or two in order to make up for this voltage drop.

does this controller have braking?

What should should be the supply dc adaptor rating if i want to control two 12 volt 0.5 A fan with pwm modulator..??

@robojax

4 жыл бұрын

Because you need only 0.5A, also most any motor module can do it. This is one of them kzread.info/dash/bejne/m6KJsbiPYK_Un7Q.html

Do you have any videos of the lower half of the potentiometer the flat spring in mine came loose and I cannot figure out where it's supposed to go

@robojax

2 жыл бұрын

Here is how to find Specific KZread Video in a channel bit.ly/findKZreadVideo

@olheghtt

2 жыл бұрын

@@robojax video is unavailable

حبيبي يا غالي شكرا جزاك الله خيرا هذه الداءره ممكن احمل عليه

@robojax

3 жыл бұрын

و ایکم.

60M PWM Speed ​​Control Circuit hello, can I ask you a bit, can this circuit be used for 2 motor slowdown 24v 250W 14A .. I hope you can help

@robojax

4 жыл бұрын

Yes it can. But both motor will run together if you connect them in parallel.

@Try_to_success

4 жыл бұрын

@@robojax Thank you

@Try_to_success

4 жыл бұрын

@@robojax Thank you

Con mi bateria de 36 volts cuantos amperes crees que soportara? Gracias, ya me suscribí a tu canal.

@robojax

3 жыл бұрын

Muchas gracias. la mejor conclusión es ver mis pruebas. Probé con la corriente máxima. Para este módulo, el voltaje no es importante. es solo la cantidad de corriente. Entonces, lo que sea que muestre la prueba, ese es el resultado. No recuerdo cuál fue el máximo.

This device work like a step up voltage? Input 12 volts could I vary the output volts to an higher voltage like 13,8 or 24 volts. TKS.

@robojax

3 жыл бұрын

hello, wow. If you watch it, no question will be left unanswered. the title says it is PWM. so it controls motor not by changing the voltage, but by Pulse Width Modulation PWM method. the voltage will stay the same. See the step down or Buck converters video in my channel.

@antenaseinterfacescb

3 жыл бұрын

@@robojax thank you HNY 2021.

hello,i have a 60 amp motor controler,slightly different to the one shown here, the board is green,it has 2 large relays for the h bridge,4 shotky diodes,8 mosfets,the components on the board are not marked. when used to control a small motor [12v car tyre pump] the motor runs at 90% when the display shows 00%,turning the pot takes it to 100%,is their a problem with the board? the 555 timer?, wanted to connect an arduino anyhow,i though of replacing the pot signal with one from the elegoo,but i see your replacing the 555 instead,great, dont want to return unit,eventually wish to control car starter motor,thankyou

@robojax

3 жыл бұрын

Hi, I've got the board. the video is coming in a few weeks.

Can I use this module to send pulse signal to a brushless motor ESC? I want to control the ESC with a potentiometer

@robojax

2 жыл бұрын

I hope you have watched the video ans have seen that this is connected to a motor which has only two wires. Now look at your motor and it has 2 wires it will work and if it has 3 wires it won’t

Hi tell me please I want to operate the Governor control card for the Cummins generator QST 30 his Governor is PWM signal control I fix PMU wire RPM Sencer with potential metre tell me it's working or not??

@robojax

5 ай бұрын

Hi, sorry I have no idea what governor is and how it operates

Could you also make a video on MAP and EFIE controllers?

@robojax

3 жыл бұрын

Never heard of MAP or EFIE.

Hello Brother Nice job done ....but I need ur help regarding "bh-17n-d pwm" How could i connect this PWM knob with Electric bike throttle beacause this bh-17n-d pwm circuit knob have 5 wires and my throttle having 3 wires.....plz guid me.

@robojax

Жыл бұрын

Your electric bike might have brushless motor dC also called BLDC. If that is the case then you can’t use this module. If it is simple DC motor with two wires then you can use this .

@imrangul4771

Жыл бұрын

@@robojax no its not bldc its simpl brushed motor 1.2 kw 24 v

Hi.. I think the U4 IC is the mosfet gate driver. Is it the gate driver? Or is it MCU? What is your guess? OR will we not know exactly what this component is?

@robojax

2 жыл бұрын

Hi, this does not and should not have gate driver because we don't change the direction of rotation and we don't need high-side driver. here is the hack to use this driver with Arduino kzread.info/dash/bejne/nWVny7amprPahbg.html

@soneralpay7565

2 жыл бұрын

@@robojax Hi.. Thanks Sir.. U4 8 pin soic MOS, MCU or ECU (EPROM)?

A Great Review of this board. Thank you...!!! I have ordered 2 of these for my project. (Sawmill) Has anyone hooked up a Digital Read Out for the % of PWM the motor is receiving from this board? Or do I need to do this using an Arduino UNO etc? A Schematic would be helpful? A Link maybe? Thanks!!!

@robojax

3 жыл бұрын

Hi, look at this, it might help kzread.info/dash/bejne/nWVny7amprPahbg.html always search my channel, you will be surprised.

@waylonj4078

3 жыл бұрын

@@robojax Yes Sir... I did follow the links to your main site and did watch the video for using UNO as the PWM However, my question was, can a digit counter be added to the ESC board without using a microprocessor board to display the percentage of the PWM..? I already follow your amazing site and appriciate the effort you put forth on all your projects. I don't know where you find the time to reply to almost every post. Keep up the good work. ..!!! And Thank you...!!!

@robojax

3 жыл бұрын

Yea you can use any device that generates PWM.

@waylonj4078

3 жыл бұрын

Thanks Again..!!! :)

Sir shall I connect this module to control 24VDC motor??? Plz replay me.

@robojax

3 жыл бұрын

Perhaps you skipped the video. you posted this comment 10 hours ago and perhaps you will read it few more hours later. Read the title of the video.

Hi I was wondering if anyone has the schematic drawn up for this motor controller or not. Thanks

Can this be used with Arduino to dim LED lights using PWM?

@robojax

11 ай бұрын

Check my channel or link in description for that video I already have

Can we connect 220 directly from the socket?

@robojax

2 жыл бұрын

This is DC. You can’t

hello friend i have the same speed regulator. why when the voltmeter is all at zero i motor always turns to the maximum? help

@robojax

3 жыл бұрын

Hello, I am not sure where you are measuring from. But at the motor terminal you should get the actual voltage.

@giuseppebiasi5177

3 жыл бұрын

I mounted a 12v battery on the pawer terminal it gives me the same voltage on the terminal that goes to the motors

is it possible to replace the potentiometer with ebike throttle to control speed?

@robojax

3 жыл бұрын

Yes. if the eBike throttle IS made of potentiometer. Disconnect it from bike, measure connect it to multimeter and turn the throttle, if the value changes, then it will work. learn about apportionment here kzread.info/dash/bejne/hpaAxqOKoKiamqg.html good luck

@dingski_diy

3 жыл бұрын

@@robojax thanks

@dingski_diy

3 жыл бұрын

@@robojax the throttle is hall sensor effect type

@robojax

3 жыл бұрын

then it won't work. this needs actual voltage to change to control the speed.

128/5000 Did you try to control with Arduino DC-10-50V-60A-3000W-Module-Driver-PWM-Speed-Controller-12V-24V-48V with Arduino

@robojax

5 жыл бұрын

this is not made for Arduino. But I will look at controlling it with arduino.

@draskillqc3857

5 жыл бұрын

@@robojax Thank You

What happens when the 36 volt motor of the scooter is exposed to 50 volts?

@robojax

3 жыл бұрын

Overheat first and in few moments if you don’t have fuse or protection, you should see smoke and it will die.

Hi Sir, can this module to control pwm solenoid coil?

@robojax

3 жыл бұрын

HI, Solenoid must have something to control the pulses. never heard that. It may work. I am not sure. if your solenoid needs PWM, then it must have 3 wires. VCC, GND and PWM.

hi, could you put the link where you buy it?

@robojax

11 ай бұрын

The link is I. Description I believe

@smecmanca

11 ай бұрын

@@robojax there is not

Can you share the link where i can buy it please, i shall be very thankful to you

@robojax

2 жыл бұрын

please check the description of video. I added the link.

so am i right in saying this unit can not handle 60A? from what i saw this unit can only handle 30A

@robojax

5 жыл бұрын

depending on your voltage you can get higher current for example if use it for 5V you might get 40A or 50A . Watch till end of video.

@freelectron2029

5 жыл бұрын

@@robojax yes i watched all the video. as i said. i did not see any capability of this unit reaching 60A.

How can we control 40 servos and is it possible

@robojax

5 жыл бұрын

Use this module kzread.info/dash/bejne/q2yMm7pqYLfUYc4.html and connect output to the 60A module. You can cascade multiple servo controller to have 40 servo controlled

How can I connect it directly to Arduino PWM pins ?

@robojax

2 жыл бұрын

all my videos have links under the video in the description. there is separate video on that. Here is how to find Specific KZread Video in a channel bit.ly/findKZreadVideo

How to connect bldc motor controller

@robojax

3 жыл бұрын

If you mean brushless motors, this will not work. Just dc 2 wires.

input current voltage

@robojax

4 жыл бұрын

it is mentioned in the title of the video and I mentioned in the video. The current was tested. Watch the video without skipping. All your questions will be answered if you watch it fully.

Try Test pwm 100a very high quality

@robojax

4 жыл бұрын

I would have to find it. Did you check the link (in the description) about this item on how to control this using Arduino?

@broucezhao8599

4 жыл бұрын

@@robojax You can click here,friend.100A 150A also have.

What is the frequency?

@robojax

16 күн бұрын

the link to the product is provided in the description of video. Click on one of them and I am sure you will see it. specially AliExpress has the frequency.

@randyledbetter3408

15 күн бұрын

@@robojax Is a digital speed readout hook-up possible?

Can you share the schematic diagram of this circuit please

@robojax

5 жыл бұрын

this is commercial product. You don't need to re-build it. Just get and use it. Or spend some time and draw it yourself.

@munkazatips8994

5 жыл бұрын

@@robojax thanks sir....

Do you have a shematic file?

@robojax

4 жыл бұрын

I don't have it but what are you trying to do? if you try to build this, it would cost you more than buying it.

@1k11coientu5

4 жыл бұрын

@@robojax thanks. But I want to create one of my drivers

What is the link to this pwm product?

@robojax

5 жыл бұрын

sorry is your question "what is the link between PWM and this product?" if so, Pulse Width Modulation signal at the input will allow to control the speed of motor while keeping the voltage unchanged. For example input to this module can be 12V and also output will be 12V but using PWM you can change the speed of motor.

@martinfeux32

4 жыл бұрын

www.amazon.com/Controller-10-50V-Driver-Module-Extension/dp/B07B4B2X35/ref=sr_1_8?crid=M0HRWYPPGP10&keywords=pwm+controller&qid=1578072596&sprefix=pwm%2Caps%2C167&sr=8-8

My question to anybody that would be able to provide an answer can I use this type of controller on my Bird-2 36 volt e scooter

@robojax

2 жыл бұрын

just check the motor. if the motor has 2 wires, then yes you can use it.

@JzNMuzak

2 жыл бұрын

@@robojax It has three phase wires , along with hall sensors.? I guess that's a no?

No entiendo el motivo del fabricante. Decir que soporta 60A.

@robojax

3 жыл бұрын

No lo recuerdo, pero creo que este módulo puede manejar 60A. Cada mosfet puede manejar más de 50A.

Is there any schematic!

@robojax

4 жыл бұрын

why you need schematic? to build it? the module is so cheap, if you want to make it, it would cost 3 to 4 times more just the components. If you want to know how it functions, just take it and draw it. you can can it in less than an hour.

@krisea3807

4 жыл бұрын

@@robojax If cheaper than making one that is fine, I'll buy one,

This board can connect with Arduino PWM. signals

@robojax

3 жыл бұрын

Yes the link is in the description of the video. But here for you kzread.info/dash/bejne/nWVny7amprPahbg.html

@koontaweegroup6695

3 жыл бұрын

@@robojax so. I watched the vdo from link. ,. How many baths (thai) ?

Sir I am interested for this device to perche quickly buy it now I am waiting for your help me with a link to perches on this device I wont to be a requirement to 90A pwm moter controller module what a market in a local & Indian market i am a Gujarat state (India) what a name of market in module

@robojax

5 жыл бұрын

Hi, the name is in the title of video it is "DC 10-50V 60A 3000W" but if you are looking for 90A I have no information on that.

@hhogasproduction5081

5 жыл бұрын

Sir I want to be a DC 10_-50v to 60A. 3000watt a kit for ready to perch me so. I am waiting for your help.where is perched.so help me

@robojax

5 жыл бұрын

Search google and it will tell you the store near you. Or Amazon

Do you sell this item?

@robojax

2 жыл бұрын

No

السلام عليكم ورحمة وبركاته أنا مصر من طنطا محتاج قطعه مثل هذا كم سعر ها وكيف احصل عليه ارجوك

@robojax

3 жыл бұрын

وعليكم السلام، و رحمة الله و برکاته من السهل جدًا الحصول عليه. يمكنك شرائه من موقع eBay أو AliExpress أو أمازون ، حيث يبيعه كل متجر بسعر مختلف. فقط تحقق منهم. آمل أن تفهم أن موقع eBay هو www.eBay.com وأن AliExpress هو www.AliExpress.com أو ابحث فقط على Bing.com أو Google.com ويمكنك العثور عليه بسهولة. أحمد من كندا

@user-vy3gv5jt5k

3 жыл бұрын

@@robojax حبيبي احمد باشا انا ابراهيم النجار لصناعة عربية اطفال قرية بتوفر كفر الزيات غريبه ارجوك ساعدني هذه قناتي على اليتيوب انا عامل عربية اطفال كهرباء كل علي ايدي مم تشوف القناه لانى محتاج داره مثل هذه لان بشغل المتور مباشر

where can i pay it?

@robojax

3 жыл бұрын

just copy the title of this video and paste it on Google or Bing and you will see 100s of options

NEED IT , the price please

@robojax

4 жыл бұрын

Wow. you waited so long to get the price. Look at the title "dc 10-50V 60A 300W PWM" if you search this on google you will get the price. Why you waited this long?

حضرتك من اى دولة

@robojax

3 жыл бұрын

انا من کندا. اصلا من الخراسان الکییر .

ขายไหมครับ

احمد باشا انا ابراهيم كم سعر ها بلمصر ى

@robojax

3 жыл бұрын

سعدت بلقائك ابراهيم. أحمد من كندا ، أصلا من خراسان الكبير

@user-vy3gv5jt5k

3 жыл бұрын

@@robojax حبيبي احمد اسم غالي

haha my diy controller can handle 30- 40 at 24 volts🤣

@robojax

3 жыл бұрын

yes. and you can control it using Arduino. Check the link in the description or serach.

Speed control electric drill so chip.....

@robojax

Жыл бұрын

this is very big but yes it will work.

NO NO ,need pwm , 3000W ,dc motor speed controller

@robojax

4 жыл бұрын

YES. YES. this IS PWM Speed controller.

Ammm you didn't get up to 3000w!!! So not conclusive and one moset going out is not good ...

@robojax

Жыл бұрын

You saw it heat up. 3000w is just fake

@nickblacksoul4318

Жыл бұрын

@@robojax yes I know but I would be more dramatic giving the full power and see it fail I would made a nice how to fix vid

حبيبي ياغالي احمد باشا انا ابراهيم عندي قناة على اليوتيوب ابراهيم النجار لصناعة عربية اطفال قرية بتوفر كفر الزيات غريبه ارجوك ساعدني هذه قناتي على اليوتيوب ممكن توشفها لنى عامل عربية اطفال جميلة

@robojax

3 жыл бұрын

أخي العزيز. لقد زرت للتو قناتك. لديك مشكلة كبيرة. لن يعثر الأشخاص على مقاطع الفيديو الخاصة بك أبدًا لأنه ليس لديك إمالة مناسبة للفيديو. عليك أن تفكر بهذه الطريقة: لماذا سيرغب الناس في مشاهدة مقاطع الفيديو الخاصة بي؟ هناك الملايين من مقاطع الفيديو على youtube وتريد منهم أن يشاهدوها. لذا اكتب العنوان الصحيح الصادق لكل مقطع فيديو واشرح ما سيراه المشاهد. إذا كنت تكذب في العنوان ، فلن يعودوا لمشاهدته أبدًا. لذا قل الحقيقة وفسرها بشكل صحيح. كما شاهدت أحد مقاطع الفيديو ، لماذا ينتظر الناس مشاهدة الفيديو الخاص بك الذي يظهر طفلاً يركب دراجة نارية؟ الناس لا يريدون مشاهدة تلك الأشياء. إنهم يريدون أن يروا وقتًا ممتعًا أو ممتعًا أو شيئًا للتعلم. مشكلة أخرى هي أن جميع مقاطع الفيديو الخاصة بك تقل عن 30 ثانية. لا ، لن يشاهد الناس. آخر نصيحة. إذا كنت تخطط لكسب المال من KZread ، فيجب أن يكون لديك اسم قناة ليس اسمك. اسم مثل "wheel on move" أو شيء ما 1- إنشاء محتويات متداخلة 2- يجب نشر مقطع فيديو أو 2 كل أسبوع 3- تحلى بالصبر لمدة 3 إلى 5 سنوات قبل أن ترى 100 دولار شهريًا. حظا سعيدا.

this product not 3000w! impolible 50v 60a, posible 50v 32a, it is fake!

@robojax

3 жыл бұрын

This is the claimed rate P=IV=60(50)=3000W . As I shown and explained the components, only ONE mosfet can handle 60A if we have proper cooling. This is 8 of them. I could not test more than 20A with 24V and it was very cool. I believe this can handle it.

@ATAS

3 жыл бұрын

@@robojax no, this circuit use mosfet nce7190a max 170w. And 170x 10pcs =1700w 1700w÷50v = 34a max i am testing

@robojax

3 жыл бұрын

90 at the end of model is 90A. check datasheet.ID= drain current is 90A datasheet.lcsc.com/szlcsc/Wuxi-NCE-Power-Semiconductor-NCE7190A_C110158.pdf

@ATAS

3 жыл бұрын

@@robojax ok, but 90a not for 50v, this one mosfet max 170w. For 90a, 170w÷90a= 1.88v Ok? :)

Can this controller work with a brushless DC motor?

@robojax

4 жыл бұрын

Brushless DC motors have 3 wires and they need different controller with 3 output wires. This has two output wires.

@k22496

4 жыл бұрын

@@robojax Do you know of a motor controller that can be programmed with arduino for a 72v 3000w Brushless DC motor?

@robojax

4 жыл бұрын

I have not worked with such thing. Perhaps I should make video on that topic.