Great job, best video I've seen! Right to the point under 5 minutes, other people would have been 15 to 20 minutes and you covered everything.

@davethewoodworker1043

2 жыл бұрын

Thanks I try to get straight to the point

I expect this mower will last several seasons with decent care. kzread.infoUgkx1VWTrayKBdCKAjzAcZ_Eg4dhHTae3LkN also recommend Also, I ran across the problem with it not starting the 2nd time I used it. There is a safety switch which is pushed in by the chute or mulching piece being attached to the deck. I took the cover off and it wouldn't start. Put it back on, no problem. It takes only a minute with 2 easily accessible wingnuts and no tools. This mower starts up first crank each time and it is a joy to use. It also mows in reverse by putting the key to the reverse area after starting and pushing in the triangular button. It will stay in reverse mode until you turn it off. All in all, for my homeowner needs, I really like this mower-and at 70 bucks a cut here in Miami, it's already more than 1/3 paid for itself in a month.

Great video, Dave. I need to change a spindle on my father in-law’s mower and this was just the information that I needed. Thanks!

@davethewoodworker1043

3 ай бұрын

Thanks and you're welcome

Thank you Dave this tutorial made life so much easy. Ran over a piece a rebar busted the spindel, I was back pushing the old lawn mower kinda brought back some memories of the old days lol. With this video im glad them memories faded quick if ubknow what i meanThanks again. I bought mine of Amazon ran about $30 hope it lasts

@davethewoodworker1043

2 жыл бұрын

Glad it helped 😊

You have a gift. Quick to the point, thorough. Subscribing!

Short, sweet, and to the point. Thanks!

@davethewoodworker1043

2 жыл бұрын

You're welcome

No body shows where to put that little washer but you, thanks this is what l was searching for

@davethewoodworker1043

Жыл бұрын

You're welcome

Hey Dave - thanks so much for this great video! I ran over something and had to replace. Short sweet and informative! Thank you for not making this a movie - a long damn video! Take care!

@davethewoodworker1043

2 ай бұрын

You're welcome

Excellent video, clear and simple. Thank you

@davethewoodworker1043

Ай бұрын

You're welcome

How do I get the nut back on top the pulley with out it spinning ? Holding the pulley doesn’t work.

Great job!

Superb video! ..happens to be the exact mower I have! Thanks!

@davethewoodworker1043

Жыл бұрын

Thanks and you're welcome

Great video man! Helped me alot!🤘🏽🔥🔥🔥

@davethewoodworker1043

2 жыл бұрын

Thanks, glad it helped

Appreciate the video. Great step by step. Only thing to add is that you should have something to vertically lean the deck against to make the spindle install easier.

@brandonworthington1305

11 ай бұрын

Also, if you’re replacing a side spindle (like I was), don’t forget to reseat the belt before you put the shroud back on. Otherwise, you’ll be pulling the deck back out again after putting all the cotter pins back on…not that I did that, but I did.

Dave, thanks, brother, for the video!

@davethewoodworker1043

10 ай бұрын

You're welcome

Got me fixed up. Thanks for the video

@davethewoodworker1043

Жыл бұрын

You're welcome

Good video 👍🏼I needed something like that so I can change mine

@davethewoodworker1043

2 жыл бұрын

Thanks

thanks, great no nonsense video

@davethewoodworker1043

3 жыл бұрын

You're welcome

Thank you very informative, now i can do my own!

@davethewoodworker1043

2 жыл бұрын

You're welcome

Good job, thanks for the video!

@davethewoodworker1043

11 ай бұрын

You're welcome

Very helpful. Thanks.

@davethewoodworker1043

2 жыл бұрын

You're welcome

Great video!

@davethewoodworker1043

2 жыл бұрын

Thanks

Helpful tip before you put the new spindle on put the nut on knock out the spindle shaft from the top it will drop out take the inter plastic washer off the bearings then Insert the spindle shaft back into the spindle housing from the bottom add High temp Grease . Removing the plastic washer from bearing Allows grease to reach the bearing rollers makes everything last longer. And yes if spindle housing is still good but the spindle shaft is bent or bearing went out you can just replace the shaft or bearing keep from replacing the whole assembly and save money a time

Thank you!

@davethewoodworker1043

3 жыл бұрын

You're welcome

I was trying to replace the blade, but i snapped the head of the blade bolt off. If i buy a new mandrel assembly, how can i remove the top nut without having a blade to hold on to? I tried using extractors to get the bolt out. But that didn't work at all. I don't have an impact wrench or fancy tools.

@davethewoodworker1043

3 жыл бұрын

Break the aluminum spindle and use pliers or vise grips to hold the shaft

awesome -thank you

@davethewoodworker1043

Жыл бұрын

You're welcome

I did what you said took about half hour .thanks for making it easier. I have another problem if you could help. I have a spark on spark plug wire but when I put new spark plug on end of wire checked it against body no spark comes through spark plug. It was running fine before it quit. Plenty gas coming up carburetor.

@davethewoodworker1043

2 жыл бұрын

Make sure blade switch is push down

Also thank you, I sent vid to help nephew.

Thanks!

@davethewoodworker1043

2 жыл бұрын

You're welcome

Thanks for the instructive video! I notice you didn't use a threadlocker agent when attaching the spindle to the deck. I would have thought this would be worthwhile, given the vibration involved. I can imagine the bolt working its way out. Is there a good reason NOT to use it that I'm missing? About to do mine.

@davethewoodworker1043

2 жыл бұрын

Thanks, well I replaced a bunch over the years. Never once had one to come out, but you can add some

@rob1733

2 жыл бұрын

Much obliged!

Hello I recently removed mowerdeck from tractor to replace broken spindle and I lost hardware to re mount cutting deck to tractor. What parts do I need to reconnect the mower deck to tractor ??? Please help 😢😢

Where do I purchase a replacement spindle? Thanks!

@davethewoodworker1043

3 жыл бұрын

I ordered mine off of EBay.

Everything worked until I started to pull the deck out but there was a wire connected that prevented me from doing so. It ran all the way up into under the hood and hooked up back in the middle in front of where I took the pin out and then connected to a wire on the other side???

@davethewoodworker1043

2 жыл бұрын

I don't know what a wire would be hooked up too, unless they changed something on newer models

When putting in the grease, I pumped and pumped but no grease ever came out the “other side” as you say. Where exactly does it come out?

@davethewoodworker1043

3 жыл бұрын

It usually comes out around the bearing, or around the grease fitting

@mpyoung33

2 жыл бұрын

Most of the time these spindles come with sealed bearings and the grease will sit on the seal. The spindle needs opened up and the inner bearing seals need removed.

Nice trick by using the nut to remove the pulley

@davethewoodworker1043

11 ай бұрын

Thanks

good job,would of been worth your while to sharpen blades as well:)

How many hours of Labor are involved in rebuilding pool deck Husqvarna 24/48

@davidmisuraco8853

Жыл бұрын

Full deck. I was charged for 4 hours labor.

@Sinoops

Жыл бұрын

1-2 hours. Really should be 1 hour for anyone that knows what they are doing.

Good share man. How long did this take you overall to replace the spindle? I’ve got the LGT 2554. Hoping to find a single spindle for sale, just broke my one side of today. Please let me know whenever you get a second.

@davethewoodworker1043

3 жыл бұрын

It varies, I can replace the outer ones, without taking the deck off. If you have a Rural King near by, they usually have them in stock. But I have bought a few off EBay. I would recommend having 1 as a spare on hand

My bolt keeps spinning. The spindle underneath is completely stripped out. I’ve tried holding it with vice grips and am using an impact gun. I guess I’m just SOL

@ahsuser

2 жыл бұрын

Shucks - me too :(

@Sinoops

Жыл бұрын

Same thing here :(

Yeah try doing it after all 4 points that hold the spindle to the mower deck break

@davethewoodworker1043

Жыл бұрын

Yeah that's harder

A whole lot of extra work taking the deck apart, there is no need to take the deck off. Raise the rear of the tractor with a jack on the tail hitch or run it up car ramps, chock the front wheels you are off to the races, done it a dozen times never an issue.

@davethewoodworker1043

Жыл бұрын

But by doing it this way, I can film it better

@miked7350

Жыл бұрын

@@davethewoodworker1043 That makes sense, sorry for nit pickin. I used to remove the deck for a snow plow and it aint no fun. Thank you for the video

@davethewoodworker1043

Жыл бұрын

@@miked7350 you're welcome

I mow my grandparents lawn with one of the bigger ones of these, idk a 750 cc engine or something. Anywho, i brought it back home (very close, just drove it) mowed some and BOTH spindles sheared/cracked off and both blades ruined. Noticed the grass wasnt shooting out so i checked. They went and got spindles at a local spot which just gave me the casing....no bearings no actual ''spindle'' aka where you bolt eveyrthing on. The old bearings are gonna be ruined coming out and the spindle, how the blade indexes is all boogered up. Sad paying 35 or so dollars per spindle to get 1/3 of what i need. Ebay ect could have it in a few weeks,a bit too long though. Always time that is the factor

@davethewoodworker1043

3 жыл бұрын

We have a Rural King here, they usually have them in stock. But they are cheaper on eBay. I usually keep a spare now, just in case

@davethewoodworker1043

3 жыл бұрын

I have also just swapped out the bearing and spindle from broken ones to new ones

@baileyhatfield4273

3 жыл бұрын

@@davethewoodworker1043 Thanks for the reply, yeah it's my grandparents ride on, but i might see about getting a spare atleast. I got no problem changing it by any means just getting parts yeah. Gonna check another spot tommorow. Basically everything in them was trashed, besides possibly the bearings. Thanks

new blade

what is the name of the deck spindle?

@davethewoodworker1043

2 жыл бұрын

Are you talking about brand name?

@davethewoodworker1043

2 жыл бұрын

Some call them spindle assembly

@francislang5075

2 жыл бұрын

@@davethewoodworker1043 brand name

@davethewoodworker1043

2 жыл бұрын

@@francislang5075 it doesn't matter, all made in China. I bought some off eBay and some local

@francislang5075

2 жыл бұрын

@@davethewoodworker1043 thanks dave

Spindle husqvana ride on

the spindle housing is broken it needs to be replace

Dave, I think I can do it without taken the blame deck completely off Dave.

@davethewoodworker1043

Жыл бұрын

You can on the outside one's, but I took mine off to show a better view for camera

Most if not all of these greasable spindles have a sealed bearing on lower side so no grease goes in lower bearing from zerk. The fix is to disassemble the spindle, remove cover on inner/top side of lower bearing & hand grease its lower bearing then or reassemble then fill the assembly with grease via zerk. Idk why both sides of the lower bearing has bearing covers in a greasable spindle assembly but they sure do? The lower bearing is what fails most times too.