Excellent tutorial with good verbal descriptions during the operation 👍👍

@Motorcarnut

Жыл бұрын

Thank you, appreciate the feedback!

Thank you very much for this video. Helped me so much

@Motorcarnut

2 ай бұрын

Glad to hear it! Thank you for the feedback!

Thanks for this video. I just did this job today on my 2010 Mazda 3 S. Mine has ABS, and the ABS sensor was attached with a odd little star shaped bolt, probably E-torx, but I'm not super familiar with those. I was able to easy remove it with a regular 5mm combination wrench. Also, on my car, the bearing hub assembly was held together with a regular socket bolt, so I didn't even need the big Torx bits you used. And yes, it's possible to remove the entire brake caliper/bracket if you want to save time and you're planning to re-use your same brakes. Just be prepared to use a beefy 14mm combo wrench, because on my model, a brake line runs right over the one bolt, prohibiting a standard socket wrench. Thanks again for the help!

@Motorcarnut

4 ай бұрын

Thank you as well for the great extra info!!!

Thank you for this video

@Motorcarnut

Жыл бұрын

You're welcome, thanks for the comment.

great video thank you!

@Motorcarnut

Жыл бұрын

Thanks for the reply

Thanks for the video bud

@Motorcarnut

Жыл бұрын

No problem

Easy. Good video man. I need to do my rear-end now. I just did my front end, that was more complicated. I didn't remove the brake pads just remove the whole caliper and brackets lol:) and slide everything back on.

@Motorcarnut

Жыл бұрын

Great and thank you for sharing and the comment

@andrewadams9819

8 ай бұрын

Indeed more complicated lmao

Good note on the offset holes when mating it with the dust shield. Came across this vid to make sure I wasn't going crazy 🤣

@Motorcarnut

Жыл бұрын

Lol, no problem

Great video, thx. How much foot pound do you torque the wheel bearing hub ?

@Motorcarnut

Жыл бұрын

48 ft lbs

Are the rear hub assemblies left and right oriented, or are they universal fit for left and right

@Motorcarnut

7 ай бұрын

Universal, the only thing you have to make sure of is if you have ABS or not.

Where can I find the torque specifications for mazda 5 2010, I cant find them anywhere? The ones I find are says 170 foot pound And my wrench is inch pound with a range max 960. If I convert 170 ft pound to inch pound its around 2000 inch pound ? Also I want to know the torque on T50 screws for wheel hub assembly Brake bracket Capilar pins Lugnuts. Where will I find them ?

@Motorcarnut

Жыл бұрын

Alldata diy online $20 a month or your local library online Free should have decent repair info as well. I'm not local now or I would send them.

What is the brake dust bolt size? Don’t now anything about bolt sizes, getting my Wheel bearing and brake dust changed tomorrow….what bolt size should I buy?

@Motorcarnut

2 жыл бұрын

What do you mean brake dust boot? The calliper bolts? If so there a torx T45

@rekazu

Жыл бұрын

What’d you do to get the piston on the brake caliper to come back out? Just pump the brakes like normal and it unscrews itself?

I have a 2010 mazda 5 , should i order wheel bearings with ABS sensor or without ?

@Motorcarnut

6 ай бұрын

If your vehicle has ABS then you have to order one with it, if yours doesn't have ABS then either one is fine.

I noticed the new hub has the abs port. Does it matter? I ask bc I just bought a hub yesterday and the non-abs was $20 more.

@Motorcarnut

Жыл бұрын

No, as long as your car doesn’t have abs

Only comment would be you can just pull the entire caliper off with 2 bolts and then slide it out

@Motorcarnut

8 ай бұрын

True, but it’s a little bulkier that way, but yes.

The 4 bolts T50 are stuck, any suggestions to get them off??

@Motorcarnut

Жыл бұрын

Heat, but be careful

Can you show one with the 4wd mazda 5?

@Motorcarnut

Жыл бұрын

I don’t have one right now to show, it’s similar except for the axle nut that has to be removed.

The fronts are not assemblies like this right? It's like a press bearing style

@Motorcarnut

Жыл бұрын

Correct

is this similar fora cx-5

@Motorcarnut

3 ай бұрын

Should be

@autograph415

3 ай бұрын

@@Motorcarnut I've got a question mlt sure if you can help or not, so my mazda cx5 i think is a wheel bearing but not entirely sure, it sounds more like a whistling on the passenger side more then a growling, could that still be a bearing

@Motorcarnut

3 ай бұрын

Yes

What's the torque spec?

@Motorcarnut

Жыл бұрын

The rear hub assembly is 50 ft lbs

Would this cause the car to shake when going 50-55 mph?

@Motorcarnut

6 ай бұрын

Not really, unless it was getting ready to fall off.

@duranl24

6 ай бұрын

@Motorcarnut Ok, thank you!

@Motorcarnut

6 ай бұрын

@duranl24 no problem

7mm allen if any one asks 👍

@Motorcarnut

Жыл бұрын

Thanks for that info

What is the torque spec?

@Motorcarnut

11 ай бұрын

50 ft lbs