RC composite plane build tips&tricks
Тәжірибелік нұсқаулар және стиль
Designer and builder a large scale RC models of the A314 Super Tucano, A6 Intruder, EuroFighter and many others. From 3D design to using 3D printed parts to making the plugs. Then build the molds and layup the model ready for test flights.
Best solar panels that I use on my trailer and camper for Battery charging amzn.to/3wlAJcF
PLA for my 3D printers amzn.to/3SzhO5c
Best remote power switch I ever purchased amzn.to/4beLRI6
Control surface throw meter amzn.to/49aiLI0
Best resin for scale parts and is less brittle amzn.to/3OHwZHT
Resin printer that I use for scale parts amzn.to/3N5tjAr
The clay I use for molding seams amzn.to/3AiFBOb
My 3D Printer for PLA parts like five bladed prop hub amzn.to/3QTjDsu
My Laser Cutter Really good quality and ease of use amzn.to/3XItNP1
Best Deal,CA Glue with Activator (2 x 3.5 oz - 2 x 13.5 fl oz) amzn.to/3YZrJUj
Used for trimming cloth on mold 120 Utility Knife Box Cutters amzn.to/3GaFO8V
Snake Thingie For camera amzn.to/3QcyZrZ
Work light with phone charger amzn.to/3VhgweO
Link for the shop led light stripsamzn.to/3jogbtc
The PLA I use to create all my 3d parts amzn.to/3v70nxR
Best deal utility chip brushes for the epoxy resin amzn.to/3GbTVvJ
6 OZ fiber glass cloth I use for both molds and layups of models amzn.to/3HS0epB
Scales I use for both thrust test and weiging planes amzn.to/3hIrUm2
Laser I use for aligning parts to make plugs with amzn.to/3WjoaGC
Surface putty I use for fuselage detailing and building plugs amzn.to/3Wyke4A
Mouse I use for fusion 360 Designs amzn.to/3Icx4Sn
PVA Parting agent I use in molds prior to layup amzn.to/3BVQTZX
Microspheres I use for thickening resin and making goop for details amzn.to/3Gbmolh
Remote control of lighting zones in my shop amzn.to/3Vntcka
15Amp 500 ft range remote power switch for lights, equipment etc Best I’ve ever used amzn.to/3sbkpJE
Пікірлер: 22
One of your early videos just popped up on my feed. You have my attention, subscribed. Still going through them. I'm not into jets that much but like watching your molding techniques, which can be used broadly. Your excellent results speak for themselves despite the odd hiccup (I like that they are included). Really appreciate the time you have taken to share your experiences.
Lots of great tips and tricks, thank you for sharing! Its saved to favorites now 👍🏼
Subscribed and enjoying your channel. Thank you for sharing your knowlege and experiance.
thank you so much for all the help...
Great video, thank you for sharing your experiences and tips!
Subscribed. Great video. Thanks for sharing your knowledge
Great tips , many thanks
Bummer with the bearings but seems that you've put the time into good use by sharing these tips & tricks! Much appreciated, especially the point about cutting/trimming the ends of cheap brushes that easily pick up cloth... Will put that tip into immediate use, hadnt even thought about it before but now seems so obvious...! 😅
Very good thanks!
Wonderful channel with lots of very valuable tips for molding and glassing. I have followed your RC Groups posts and just found you on KZread. A couple of things I would find helpful would be some videos on making a plug for a project and also how to make a mold for the plug. Thanks again for shring your experience
@britcharming
4 ай бұрын
one in the Tucano series and A6
Superb !!!
Very nice work
Great videos. I appreciate your efforts here and the amount of detail you add to your builds are amazing. How long did the Tucano take you to build, from the start of the first plug until the airplane was ready to fly?
@britcharming
3 ай бұрын
Thanks The Tucano was about 18 months total with 200 plus hrs of CAD design.
Great video, do you have a video, do you have a video that shows were you make the design? I am guessing a CAD software? And how you make the molds from scratch? New subscriber.
@britcharming
4 ай бұрын
I use fusion 360 for CAD. And no I don't have a video of designing the models. However, I show a bit off video CAD making the five blade prop in the Tucano series
What is the mixture of Splooge?
@britcharming
4 ай бұрын
mix the two part resin first. Then add your filler to a mayonnaise consistency or however you want it for the job you're doing. No particular mix it just depends what you need it for
Do you vacuum bag your molds? Or just use the filler to get your details
@britcharming
Ай бұрын
Sometimes it depends on the part I need. For the fuse I just use the filler with no vac.
@nicholaskillian6098
Ай бұрын
@britcharming gotcha, been wanting to get into composite since I have a cnc to make molds but don't wanna get into bagging if not needed