Hey everyone! I would love some recommendations for channel video ideas. What do y'all sugest?

@Nope-iw7fm

5 ай бұрын

Want to check podman out? It's similiar to docker but its daemonless and can be run rootless!

@codefallacy

5 ай бұрын

Nice! i always hear that Podman is the FOSS alternative to docker but i have never tried it. this is a great opportunity to do so, it will go in my video ideas board!

@Volker-Dirr

5 ай бұрын

@@codefallacy I suggest buying a power measurement device and measure the needed power. There are so many channels out there that think always the 27W power supply is needed, even that is not true. I measured between 7W on full load (sysbench) up to 11W on full load (my own benchmark). So my pi is running fine with a no-name 3A = 15W power supply. But i am using a SD card only. With such an SSD of course it might be to less power. So i am interested in that. So far I saw only one other German channel that use his Pi even with a 2A = 10W power supply only. But he is using his Pi mainly only with single threaded apps, not with full load. A power measurement device is cheap. Only around 10 Dollar. I suggest to buy one that is connected to your power socket, not to the USB, since that sometimes makes trouble since the cheap ones don't let the PPD signal trough. I done already some measurements, but without SSD. I think I don't need SSD in my use case. Maybe see my channel. Maybe also measure with overclocking. I haven't done that, since I don't like overclocking much, but i think many other guys like overclocking.

@ksoonsoon

5 ай бұрын

BTC is a big-deal ATM for known reasons. How about a series for setting up BTC nodes with each of the known software options?

@codefallacy

5 ай бұрын

@Volker-Dirr that is a great idea, i have a few power measuring devices, i did a whole power measuring of the raspberry pi 4 and im very curious what the raspberry pi 5 actually consumes! this will go on the video board for suren

Found your video by accident and appreciate how thorough you were in describing and showing on screen what you were doing. Job well done! Subscribed.

@codefallacy

5 ай бұрын

Thanks for the feedback!

Great video! The Pi benchmark site & utility is epic! I'd missed Jeff Geerling's NVMe gen3 settings in that config file so now, thanks to you, my Raspberry Pi 5 is even faster! Subscribed...

Great article, thank you for going through the procedures step by step! I ordered one after viewing your video!

@codefallacy

5 ай бұрын

Let me know how it goes for you when you receive it. some users have reported poor quality issues with geekworm in the past.

You explained this very easy, thank you.

Thank you! The clearest explanation yet for this. Let's see that NAS! Robert'

I have the X1000 & X1001 & I too was also able to keep my heatsink on but I replaced their mounting screws with standoffs & moved the M.2 boards as up high as I could away from the heatsink to free up the fans airflow, so it keeps both cool. I also added feet to the board, to keep the underside of the Pi cool, but also in case I spill my coffee on the table so it doesn't get destroyed.

Very insightful Luis, thanks for posting the video for our knowledge. Much appreciated!

@codefallacy

5 ай бұрын

Thanks for the support!

Great instructions for setting up the GeekWorm X1001 on Pi5 with NVMe.

Great video. Useful and interesting

Can't thank you enough!! I learned so much from you. Cheers!

Great demonstration, I'll be getting a pi5 soon and will use this as a reference. Thanks

Awesome to finally see the x1001 - thanks. It should leave enough space for the Pi to be fitted in a rack mount 1U - I think.

Outstanding video! Thank you. I am just waiting on my Argon case with PCIC NVME holder to arrive.

@codefallacy

5 ай бұрын

awesome! let me know how it goes for you!

The Pi5 with GWx1001 NVME board installed fits perfectly inside the GeeekPi Metal Case for Raspberry Pi 5 (on Amazon).

Great video. I also did the same "oil rig" set up with some standoffs.

@codefallacy

5 ай бұрын

Nice! what kind of projects have you done?

@mikeburke7028

5 ай бұрын

@@codefallacy It's early days but I plan to go the docker route and host fileshare and databases.

awesome🎉

Me encanto el video y la explicación pues vas al grano y todo al detalle y aquí un subscriber nuevo. Saludos desde la isla del encanto 🇵🇷🔥

Finally! someone makes one about this one

I wonder how it happened that Pi for a few bucks now costs a few hundred bucks (with all the amenities) and everyone is still considering it over the miniPC

@codefallacy

5 ай бұрын

i thinks its important to keep in mind the raspberry pi is meant to be used in more ways then one. if you are only interested in server stuff then a mini pc will be better bit if you plan on doing robotics and custom projects beyond just server stuff then it is great for it.

@Rushil69420

3 ай бұрын

Just know where to go for them. The Pico is $3.99 and Pi 4 is in stock at the micro center near me starting at $45 for the 2GB. Although if you’re not in the US/UK, yeah it seems to be much tougher to get

@user-jf5ik9rh1p

Ай бұрын

30+ operating system support, iot projects, ai/ ml projects, robotics, python, c, c++, gateway projects, above all extensive community support makes it a 🌟

Thanks, good information

@codefallacy

5 ай бұрын

Thank You! i hope you like Raspberry Pi

I just finished installing this hat earlier. For the base, I got a metal one which is part of a silent all metal case. Worked out pretty well along with GeekPi active cooler. I also added an m.2 heatsink for the Nvme SSD that fits well with this hat. 👍

@jeffreylee9000

4 ай бұрын

Could you link the heat sink for your Nvme SSD. Thanks.

@xellaz

4 ай бұрын

@@jeffreylee9000 Here's the heatsink: QIVYNSRY M.2 Nvme Heatsink. Here's the case if you want the Pi 5, hat, and heatsink all to fit together: KKSB Raspberry Pi 5 Case Here's the low profile CPU fan I used if you're interested: GeeekPi Active Cooler. I tried to post direct link to Amazon's page but KZread keeps deleting it. Just search for them instead. Good luck! 😁 Edit: Just note that I removed the sticker on the Nvme M.2 SSD prior to putting this heatsink for better thermals but this might also void your warranty if you decide to do this. For me, no regrets yet and temps are great! Around 34°C idle and 41°C on load using pcie x1 Gen3 speeds.

@xellaz

4 ай бұрын

@@jeffreylee9000 QIVYNSRY M.2 Heatsink NVMe 2280 Edit: I tried to link the Amazon page but KZread keeps deleting it. Just search for it. It has a 4.8 rating.

Super helpfull. thanks

Great video 👍Thanks. Per (DK)

good stuff, I'm going to checkout your other vids. I'm interested in a NVMe RAID configuration with raspberry 5

New subscriber here! Great video. I hope to see some beta OMV7 video soon from you with the pi5 since I want to do exactly that

@codefallacy

4 ай бұрын

currently working on the OMV 6 video, since OMV 7 is not stable yet, its not a good idea to use it with real data lol

Are you going to do a video on how to run unbound as a docker container in tandem with the Pi-HOLE video you did to run it as a recursive server? Love the channel

@codefallacy

5 ай бұрын

hello! yes I will eventually, I am currently researching unbound and i have a handful of videos before getting there.

Thank u

Cool! I'd partition between OS vs data.

since overclocking the PCIe still not making it on par with the nvme ssd capability, that means, you could use cheaper SSD instead of using a high end SSD. Am I right?

@codefallacy

3 ай бұрын

you could, but there is a problem with ssd compatibility across brands. check that the ssd you are using doesnt use a "phison controller" apperantly those chose controllers arent compatible and have issueswith the pi.

When you run the "shutdown " command , if you run "Sudo shutdown now" it will skip that 60 second wait timer.

@RamonInNZ

5 ай бұрын

Even add -h at the end so it gracefully shuts everything down.

@acubley

5 ай бұрын

👍 I put an alias in my .bash_aliases file for that- alias shutdownnow='sudo shutdown -P now'

I got this hat and got the accompanying case. It's been really nice with an OEM Samsung nvme ssd, but a Kingston drive was unstable. I still need to test with setting the pcie speed higher with the Samsung ssd.

@codefallacy

5 ай бұрын

let me know how it goes, another user here mentioned there may be a quality issue with geekworm. i cant confirm but im interested in how it goes for you

One recommendation for you, can you please put links to the products that you're using in your videos so that we can find them more easily on the web?

Great video and a helpful guide; thank you! I've just scored 57623 with a 2TB Crucial P3 plus (with PCIe 3 hack) Category Test Result HDParm Disk Read 824.75 MB/sec HDParm Cached Disk Read 827.38 MB/sec

Nice board. No case.

@codefallacy

3 ай бұрын

i dont buy cases anyways, i either 3d print them or build them myself from things i have laying around

I have asked ChatGPT for how to install the OS to the SSD on Raspberry Pi5, but all the answers confused me. My Raspberry Pi keeps searching the boot section from the SD card and SSD. Until, I see this video, this is an interesting solution to install an OS first on the SD card, then boot from it and try to install the OS again to the SSD storage. LIKE IT!

Hi man, great video 👍! What do you use for record the screen of Raspberry Pi? Have a nice day 👋

@codefallacy

2 ай бұрын

i used OBS and a usb 3.0 to hdmi capture card. basiccaly i plugged an hdmi cable to the pi and the other end to the capture card. i then plugged the capture card to my computer running OBS. i added the capture card as an input source

@ilmanu

2 ай бұрын

⁠Grazie 🙏 Do you Have a link for buy this card?

Great video. You need to use "shutdown now".

Спасибо! Скорость SSD Kingspec увеличилась вдвое!

Interesting video. Have to note though that you probably can’t run six hard drives on this, at least not at anything like full speed. You only have one pcie lane, even at gen 3 that’s only equivalent to 1.5 sata III ports. You can already get a 6 port sata adapter that plugs into an M.2 slot, but I don’t think it would work with a single lane.

@codefallacy

5 ай бұрын

This is true! i appreciate the clarification. even if the speeds arent there, would doing a raid mirror be better over sata than usb?

@paulbeers4105

4 ай бұрын

Most HD's max out at around 250MB/s. He should be able to get 4x SATA ports at virtually full speed. Then again, the real issue is that Ethernet is only 1gbps, so read and write maximums are moot when the network can only do 125MB/s. That can't even max a single drive.....

@codefallacy

4 ай бұрын

Great point, even adding a 2.5gbit usb ethernet adapter wouldnt help. but still, im mostly interested in the stable connection of sata over usb. ive read a few forum posts abou how RAID over a usb connection is a big no no

Thanks for the demo and info, very detailed. Can you provide the link to the products? Have you also seen the Geekworm X1003 board? Have a great day

@codefallacy

3 ай бұрын

hey thanks for the feedback. i havent provided the link to the product because i dont want people to think im afiliated with the company. but i may have to due to demand. you can buy this board either from amazon or geekworms website. i only have experimemnted with this board but i have heard great things from the x1003

@chrisumali9841

3 ай бұрын

@codefallacy thanks for the feedback, I just bought and received the X1003, let me see how this is gonna work. Have a great day

@chrisumali9841

3 ай бұрын

Update - The X1003 is garbage and does not work well. Maybe a bad unit that I got, but saw another youtube video having the same issue. I guess I will get the X1001, per your video. Have a great day

@codefallacy

3 ай бұрын

@@chrisumali9841 thanks for the update. that really sucks. my suggestion before getting another board is to look at the ssd compatibility list for that board. alot of viewers are reporting issues with certain ssds. apperantly geekworm has a wiki for it. good luck

thanks, this is exactly what I was looking for. Can you do the same but instead of Rasberry Pi OS you could do Ubuntu Server with the same method?

Great video. Could you test if a pi5 can do youtube playback at 4K? And if possible Netflix play at 4K? I got my pi4 to do it but framerate is to slow.

@codefallacy

Ай бұрын

In this video i end up using the Pi 5 as a server so i dont have a desktop to open a browser. but if you istall the desktop image you can. however note that Netflix uses a DRM technology known as Widevine that prevents 4k streaming on non certified devices. you can install widevine manually but netflix still wont send a 4k stream from their server. as far as youtube, i will have to test it out.

Hey Code, What is the length of the spacers ?? and I suppose they're M2.5 ?? or are they M3 ??

@codefallacy

3 ай бұрын

hey! i believe they are M2.5, not sure about the length since i have a asorted kit

I just bought this board from the same website, but I have one concern and I'm hoping you can help me. The Geekworm website specifically warns that SSDs, using the phison controller, are not compatible with Raspberry Pi 5. While I appreciate that you have probably already researched this for the drive featured in your video, it sells for ~$200. Do you have a method to determine which controller is being used on an SSD drive, before purchasing, so I can shop around?

@codefallacy

4 ай бұрын

SSD market appears to be way overpriced at the moment, they had an over supply last summer and ssd Nands were alot cheaper. they are probably trying to make up for lost revenue, i bought this SSD for $65 USD last summer seeing them for 200 is just ridiculous in my opinion. as far as the controller, i believe Samsung and maybe crucial, use their own controllers since phison is an alternative to samsung. but im not 100% sure. ill have to do some research myself.

@Sartre_Existentialist

4 ай бұрын

@codefallacy $65???? Talk about a markup! If you could do a little research and let me know, I would greatly appreciate it. I have tried to research this myself and have found inconsistent information where the website referencing the incompatibility specifically sites Western Digital Blue and Black drive models but when I looked up the controller, Phison was not the identified controller on those drives. I dont see a trust worthy source and controllers dont seem to be a listed tech spec. Thanks for your time

@BigZeus

4 ай бұрын

@@Sartre_ExistentialistI am also looking to get a drive that is compatible soon

@dsl3994

4 ай бұрын

I’m using a 1TB Samsung with the Phison controller on the x1002 hat with no problems at all. I’m running it as boot drive with Bookworm. @@BigZeus

Hi And thanks for the good videos. I am new to linux and have just acquired Raspberry pi 5 with 2tb nvme, and via your videos have configured it. I have the following questions. Is there a simple way to backup the configured system.? If something goes wrong. Regards, John Stephansen

@codefallacy

4 ай бұрын

Hey john, yes! there is a Linux utility called Timeshift. it can be setup to take snapshots of your system periodically. i believe its only a command line utility but there a many tutorials out there to make it work! Than you for the coffee😋

@codefallacy

4 ай бұрын

Hey john, i responded to your inquire in buy me a coffee, but i figure i also add it here as well in case (Hopefully youtube doesnt block it): i believe your error is because you are using the following command "scp john@192.168.0.111:/home/john/wireguard/config/peer3/peer3.png /Users/lpm/Desktop" what this command is trying to do is move the configuration file from "john@192.168.0.111:/home/john/wireguard/config/peer3/peer3.png" to "/Users/lpm/Desktop." the path "/Users/lpm/Desktop" is specific to me and the macbook i was using to make the video, since this path does not exists for you, you are getting this error, instead you should try replacing "/Users/lpm/Desktop" with "C:\Users\john\Desktop" so the command should be the following: "scp john@192.168.0.111:/home/john/wireguard/config/peer3/peer3.png C:\Users\john\Desktop" However i cant test this at the moment since the only windows machine i use is at my work place, so if this does not work i recommend you install "Filezilla" in windows and connect to the raspberry pi using sftp. i did this for the jellyfin tutorial at the 4:00 mark (kzread.info/dash/bejne/aZVtts6Ko9DSgJc.htmlfeature=shared) its a much simpler way of doing it. basically you will connect to the pi server with Host: sftp://192.168.0.111 username: john passoword: (your passoword) then when you are connected, on the left side of filezilla you will see a file explorer for your windows PC and on the right side you will see the file directory of the raspberry pi. and you can find the file you want to move and drag it from the pi directories to the windows directory. I hope this helps. let me know in a youtube comment if you need additional help! Once again, much appreciated

@johnstephansen

4 ай бұрын

@@codefallacy Many thanks for the reply. I will try this tomorrow. (I live in Denmark)

I have the pimoroni nvme base, it comes with rubber stickers (standoffs) and it doesn't get in the way of anything.

I hope jeff sees this video!

Well done, what a great experiment 👏🏻, can this be done to other PI's (3 or 4)?!!!!, I tried he eprom command on pi 3 and it gave me that the pi doesn't have boot loader eprom.....

@codefallacy

3 ай бұрын

i think the pi 3 has different steps for booting of usb. i did it a while ago but dont know of the top of my head. as far as i know these instructions are pi 5 specific. but booting a pi 3 over us is certainly possible

Just Subscribed I am a huge Raspberry Pi Fan and have done several raspberry pi projects, looking to use this solution you showed above to connect the new raspberry pi with 2TB NVMe as a MotionEye OS Server / Storage for my 4 raspberrpi Zero cameras

@codefallacy

3 ай бұрын

awesome! i used to run motion eye on a managed homeassistant instance when Wyze had rtsp support. i want to explore all buch of open source stuff. welcome aboard

I have the X1002 fits to the bottom of PI and does not block the SD card slot

Vine a ver el video otra ves para refrescar lo que aprendí y noté ahora que dices que lo haces de la SD por qué no tienes el adapter y pregunto si lo tuvieras pues lo hacías directo desde la PC? Estoy correcto?

@codefallacy

3 ай бұрын

si

Have you found a suitable case to fit the Pi 5 with the active cooler and the Geekworm shield?

@codefallacy

4 ай бұрын

i havent looked really, i dont usually buy pi cases i rather build them myself or 3D print them from thingyverse

Hi! Do you think a SSD NVMe of 4tb will work with pi ? If yes do you have some brands exemples ?

@codefallacy

5 ай бұрын

Hey thanks for watching, I think it may work as it is the same M.2 NVME interface. However keep in mind some users have reported errors with high power consumptio m.2 ssd drives. I only have this samsung drive i have not tested with others M.2 drives

I've been trying to get mine (I have the x1000) boot into Batocera with no luck but I'm hopeful I will figure it out soon

@codefallacy

5 ай бұрын

keep at it, you got this!

I have the NVME adapter from pimoroni, i got similar speed results by changing the Gen as you using Crucial 1TB nvme. I have however ordered this Geekworm board with case, as the Pimoroni board is mounted bellow the PI, and no case available.

@DrFunFong

5 ай бұрын

I am waiting for my Pimoroni board to arrive. I don't think we can expect a case for awhile. :)

@davideagle8837

4 ай бұрын

I was able to mount the Pimoroni board and Pi in a Geekworm P580 case. I left the feet on the Pimoroni and used longer screws to mount everything to the case. The feet let you adjust everything to line up ports and switch.@@DrFunFong

@DrFunFong

4 ай бұрын

@@davideagle8837 Thanks for sharing! I connected up a 500GB NVMe drive using PiMoroni but seem to have real latency problems. It seems to be going much slower than a Pi 4. Conky looks copasetic. I hope someone throws up a video to debug Pi5 latency issues.

Por aquí re visitando y que risa en 12:23 con “perdonen estoy teniendo un peo mental” 😂😂😂😂😂😂😂 y pues ya monte mi pi y pues refrescando la mente con este gran tutorial saludos hermano 💻🥂🔥🇵🇷🫡

@codefallacy

2 ай бұрын

jajajaj si me pasa amenudo. estoy planeando muchos videos del Pi, tambien estoy haciendo una pagina web para ponel las direcciones escritas, haci podran copiar y pegar comandos

@ElsiervoDePeFKNerre

2 ай бұрын

@@codefallacy seria grandioso, estaré esperando cuando lo anuncies para entrar.

It's incredible tutorial. thanks. I wonder how to use 32 GB RAM to Run Clusteering Server with Promox Container and Docker or K8s

@codefallacy

4 ай бұрын

im very interested in baremetal kubernetes! it will be something ill explore but not in the near future. The man, th my, the legend networkchuck made a k3s tutorial if you are interested

I have the X1001 installed in the geekworm case. I prefer to run Kali Linux. Can I boot Kali Linux off the NVME or is it only Raspian or Rasberry Pi OS?

@codefallacy

4 ай бұрын

you should be able to boot any OS after the eeprom has been updated

@neilmackinnon5573

4 ай бұрын

Okay. I had a Western Digital PC 530. It's not on the wiki list as being non-compatible but lsblk was not seeing it and other methods weren't as well. Ordered a new NVME off Amazon.

please share the purchase link for X1001. Thank you!

@codefallacy

5 ай бұрын

hey, I believe you can find it on Amazon or Geekworm's website. Im not affiliated with geekworm in any form and dont want people to think i am

Interesting device. It's cheaper than most solutions. Right now, it's NOT being well-received on Amazon and it has a very unfavorable ratings profile. Hopefully quality control will improve and it will be a good option for us all.

@codefallacy

5 ай бұрын

I agree its cheaper and smaller than most boards. I bought it from geekworm's website and it took 2 weeks to arrive because it was held by customs lol

@xellaz

5 ай бұрын

I got it from Amazon and it recognized my Nvme SSD (Crucial P3) right away. I just had to first boot with the previous USB SSD and switch the first boot to Nvme using raspi-config. After that, I removed the USB SSD and only left the Nvme SSD. Edited the boot config to pcie gen 3 speeds afterwards. Everything is running great! 👍

@DrFunFong

5 ай бұрын

@@xellaz I guess you could rely on Amazon's generous return policy to see if you have a good unit.

@yipinghuang1853

5 ай бұрын

I heard from Geekworm that the dozens of units produced just before the Raspberry Pi Foundation released the PCIe PINOUT document may have compatibility issues.

Its my first time with pi and a node , i have a pi5 i cant make up my mind if i should use a hat and nvme 2tb ssd or a sata ssd 2tb drive what would you think would be best for a btc node , any info much appreciated . thanks

@codefallacy

4 ай бұрын

either way would work since SSDs are less likely to fail than microsd cards.

I’m struggling to enable the PCIe port. I’m going to try updating the os etc like you have.

@codefallacy

3 ай бұрын

lets hope it works, i think the latest eeprom update automatically enables it. let me know how it goes

@SuperDavidstevenson

3 ай бұрын

@@codefallacy hi. EEPROM update worked. I’ve watched more videos of yours to install docker etc. thank you 🙏

I've got the Pimoroni BASE and my Pi5 is booting off the NVMe drive If you're in the UK Pimoroni are good

@codefallacy

5 ай бұрын

yeah they have a good reputation. Another user commented that geekworm pcie boards dont have the best quality assurance. other brands have better quality and the price may be worth it.

@jay_321

5 ай бұрын

I like the pimoroni base a lot and would buy one but with shipping it comes to about $38 US.

This might be silly but I’m using an old 1tb wd pidrive running a 512 botacera image. Any way I’m wondering if this would work the same

@codefallacy

5 ай бұрын

Im not familiar with pidrives but the raspberry pi allows you to boot from microsd card, usb ports and pci devices. If pidrive has a usb interface it should work.

@jny78

5 ай бұрын

Great video! Thank you @@codefallacy

missing step Edited SD card's config.txt to enable pcie.

u would think they would make the default speeds use the gen 3 speeds and not gen 2.

@jamesh9756

5 ай бұрын

The PCIe on the Pi5 has slightly too much jitter on the clock to get an official Gen3 rating. On the whole most things still work fine, but they cannot claim Gen3 compliance.

Hola !! Quiero saber si batocera es bootable desde un disco nvme instalado en una raspberry 5 ?

@codefallacy

3 ай бұрын

¿Batocera Linux? Si, tienen una imagen para el Pi, y puedes usar Raspberry Pi imager para instalarlo

Hello, I use exactly the same products as you. But when I remove the microSD card, it does not boot from the nvme disk. The LEDs on Geekworm x1001 do not light when the microSD is not inserted. I plug it in, it lights up and turns on. I check with Diskpart, whether the operating system was booted using the microSD card or my nvme disk; Used nvme.

@codefallacy

3 ай бұрын

does it recognize the ssd at all? if you were to just use it as storage are you able to save files to it? it maybe that the ssd is not compatible. which ssd are you using?

@aGGreSSiv

3 ай бұрын

@@codefallacy I have two Raspberry Pi 5s and both have different SSDs installed. One is micron brand and the other is union memory. I can write to both of them after they are opened. It recognizes both of them, but as I said, it does not boot. I don't fully understand the part about having a compatible SSD. I've seen this issue talked about on sites, but how can pi5 not use the SSD pi5 sees after booting up?

@codefallacy

3 ай бұрын

im not saying the ssd is flatout the issue, but the wiki for geekworm x1001 board says that there are compatibility issues with ssds that use the "Phison Controller", they can be found on many popular ssd brands. you can check the wiki for details. Did you update the eeprom? which eeprom is running on the raspberry pi? sometimes updating it helps. let me know which date eeprom is running

@aGGreSSiv

3 ай бұрын

@@codefallacy ; eeprom is up to date, (Feb 16) and lspci output is ; PCI bridge: Broadcom Inc. and subsidiaries Device 2712 (rev 21) 0000:01:00.0 Non-Volatile memory controller: Lenovo LENSE30256GMSP34MEAT3TA 0001:00:00.0 PCI bridge: Broadcom Inc. and subsidiaries Device 2712 (rev 21) 0001:01:00.0 Ethernet controller: Device 1de4:0001

@aGGreSSiv

3 ай бұрын

@@codefallacy : The problem was fixed when the PCIE_PROBE=1 command, which was after the boot order, was placed before the boot order command.

Hi there can you please run " dmesg --follow " and see if there is any pcie errors ? i try different hats and they all work but some of them give error messages

@codefallacy

5 ай бұрын

Sweet! ill run this command and report back when i get home from work

@codefallacy

5 ай бұрын

Good news, im not seeing any ERROR mesages when running dmesg command with this ssd and board. however some viewers have commented that they have had QA issues with Geekworm in the past. What are the specific error messages we should be in the look out for?

@GameGearZero

5 ай бұрын

@@codefallacy nice to hear you have no errors, i cant remember how they exact was , but if you have errors its not only one ,its a ton, for every use of the ssd yu got a error message (but everything is working like normal , even benchmarks give the same speed resulsts), i have to say i use a long 16pin 0.5 pitch ffc cable (covert in tinfoil) and not the official one. i stop the errors by adding "pcie_ports=compat" to the /boot/firmware/cmdline.txt. with some adapters adding "pcie_aspm=off" ( active power management) is also working. now i can use any cable without any error.

Is it possible to flash a Home Assistant Image ''haos_rpi5-64-11.4.img'' on this way? or dıd i need balenaEtcher for this task

@codefallacy

5 ай бұрын

You can! raspberry pi imager does what balenaEtcher does but much simpler.

SSD 2TB Crucial P3, M.2 2280, NVMe PCIe Gen 3 x4, Leitura 3500MB/s, Grav. 3000MB/s - CT2000P3SSD8 It is compatible with Geekworm X1001 PCIe to M.2

oh its has nvme slot, can i put gpu on that slot? external gpu

@codefallacy

3 ай бұрын

some people are trying lol. check out "Jeff Geerling" on youtube he has a video doing this

interesting but I think you can improve your presentation by briefly mentioning what the short hand like -a actually means. Then it'll mean much more to people like me!! Lots of channels would benefit from this advice. it becomes a much better learning environment then.. thanks

@codefallacy

4 ай бұрын

thanks for the feedback! ill do my best to explain the flags. in the meantime most commands will tell you what flags are supported and their name by running "--help" with it.for example the "ls" vommand has a bunch of available flags and to get an explanation you jist add --help at the end like this "ls --help" and will show all flags with an explanation

Plastic stand-offs, those brass stand-offs, and those black screws, bad idea... Invest in some plastic/nylon stand-offs so you have total isolation, or if you must (for some unknown reason) use brass, then under those black screws and under the brass stand-off place card/nylon/plastic washers.

On mine it isn't showing the 6 when trying to change the boot order

@codefallacy

4 ай бұрын

🤔🤔🤔 strange, did you update the eeprom and reboot? you could add it manually after updating

Стрим как после водника)

well, it seems it blocks the camera ports

@codefallacy

4 ай бұрын

now that you mention it, it does! they have a bottom mounted variant too, and it makes sense why they have this option

anyone else getting instability? I am using the same geekworm as in the video. I have heard issues with the power draw from certain ssd's

@codefallacy

4 ай бұрын

it appears this board does not play well with certain ssd controllers, it appears ithis drive works but others are experiencing issues. not sure which drives arent supported, geekworm should make this clear but i haven seen anything from them yet

@feralshad0w

4 ай бұрын

@@codefallacy my Samsung 990 pro m.2 worked, but showed some instability. But this could be power draw. My hynix p31gold arrived today and that should do the trick

Do you not have a heater in your house?

@codefallacy

5 ай бұрын

lol its a cold winter

Can you repeat that?

Unless you get a Samsung nvme, all my SDs outlived my EVO 980 PRO.

Hi this raspberry have 4 or 8gb?

@codefallacy

3 ай бұрын

4 Gigs

Wonderful work man! We'd love to offer you some boards if you may need them in the upcoming content. (PCBWay Daisy)😊

I have followed your tutorial step by step and I was able to boot off the device through pcie once and never again. Every time I get the following error: Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cndline) - Check rootdelay= (did the system walt long enough?) - Missing modules (cat /proc/modules: Is /dev) ALERT PARTUUID=f346a209-02 does not exist. Dropping to a shell! The main difference I have noticed is that your ssd included (bootfs, rootfs) in the naming of the device, which mine didn't. I had also converted the drive from MBR to GPT partition scheme because MBR would result in the same error. Fyi I am using a Lexar 2TB NM610 PRO which I can see with either lspci or lsblk commands and it is listed as an SDRAM Less device.

@codefallacy

3 ай бұрын

that is weird, it could be many things, have you tried reflashing the ssd and updating the eeprom once again? it could be a bad flash, or a bad board or an incompatible ssd. if yoj retry reflashing let me k ow what happens to further debug

@marcopoire9593

3 ай бұрын

@@codefallacy I have flashed the eeprom 4 times but every time I was flashing the os on a MBR partitioned ssd except for the last time which I converted it to GPT. I erased the disk every time by placing the ssd in the nvme connector in my mini pc and by using EaseUs Partiton Master. I had then followed all the steps in your guide. Lately I did a bit of reading and apparently it could be an extra parameter in the eeprom configuration settings which I am probably missing but I’d say that’s not the case because the pi is reading from the pcie slot, else a black screen would be presented on boot. Anyhow, I’ll try and I’ll let you know! Thank you for your reply btw😁.

the fact that this does nto come built in standard but has to be achieved with a plug in module is the only reason I will not be buying any more PI devices. I have a vision5 II riscv board that has this built in. Yes it costs significantly more but how muchy does the PI plus that addon cost? ok, maybe I am wrong or the info i have read so far is wrong, technically this IS built in, you just need a connector card not a whole addon board?

@codefallacy

3 ай бұрын

its valid criticism, you can get different boards or mini pc

😃

I don't know what's a "zeta"? port

@codefallacy

3 ай бұрын

i dont know either

9:03 “Shutdown -h now” if you wanted immediate shutdown

Why not show installation?

@codefallacy

5 ай бұрын

when i recorded the video the first time i did show it. but the video was too long. so i rerecorded it and cut it out.

@acubley

5 ай бұрын

and what, it's 4 screws and the ribbon cable? Good vid.

No one tells me how to rack mount the raspberry pi 5 to a 1U after adding a nvme drive...

@codefallacy

3 ай бұрын

i dont have a server rack

@adoteq_

3 ай бұрын

@@codefallacy It is not that hard, for small depth like the pi or the small Synology NAS devices you can get a 8U desktop rack, 2POST, from startech. It is ideal if you want to put your small network equipment or small devices like small NAS or Raspberry pi 4(they have rack mounts for them from utronics), switches from TP Link, rack mounts for nuc etc. It gets your cables organised

Hint: shutdown -h now

@codefallacy

4 ай бұрын

sweet! thanks for the feedback

if you run "sudo shutdown 0" it will shutdown immedaitely

Are there any of the M.2 boards which are not made in China. Considering the CCP has an actual policy of forcing manufacturers to place hardware backdoors in products they sell, I want one from anywhere else.

@codefallacy

5 ай бұрын

Im not sure, search for UK based companies making boards, hopefully they dont outsource their manufacturing

@yipinghuang1853

5 ай бұрын

This is just an adapter board, and if you're worried about backdoors, recommend consulting the Raspberry Pi Foundation.

so.. from unmodified pcie2 2.24Gb/s to pcie3 modified 3.13Gb/s writes ,good enough for over usb3 2.5Gb/s -really 2.3 average- Ethernet writes, good to know. BTW the Radxa Penta SATA HAT - Up to 5x SATA disks HAT for Raspberry Pi 5 -be sure to select the right version kit when ordering- exists now so I'm expecting no more than the 3.13Gb/s -421MB: raid0- writes throughput you show here ...a limitation of the pi5 pseudo pcie3 implementation ;Reads & writes from it are apparently good enough now for a true 5 -[4+esata enclosure]- drive usb3 2.5Gb/s Ethernet omv NAS

@codefallacy

2 ай бұрын

i just ordered the penta sata hat. im looking forward to hooking them up with 3.5 inch hard drives. the drives are so expensive though :(

@paulmaydaynight9925

2 ай бұрын

@@codefallacy ty keeps deleting my longer 'pro tip' :( search amz for 'Enterprise Class (Refurbished)' drives & then use 'victoria hdd win10' on these drives to find any bad ones, I only had 1 bad one of 5 & returned it then replaced it the next week, simples & all Good now.

@paulmaydaynight9925

2 ай бұрын

@@codefallacy yt keeps deleting my long protip about drives :( oh well..... we now need a snap together 3d printer file made up to house the 12v 10amp for 3.5hd overhead brick & pi5 5amp psu + 5 2.5/3.5hd drives -call it the pea NAS case lol.

Encontré este video por qué estoy buscando saber si se podrá usar esto mismo para correr el nodo de bitcoin, alguien tendrá alguna idea?

@codefallacy

3 ай бұрын

ahora mismo e tenido varios comentarios sobre como usar el Pi vomo un node de bitcoin, es algo que tengo planeado hacer en el futuro pero no sera pronto.

@ElsiervoDePeFKNerre

3 ай бұрын

Estaré al pendiente ya me subscribe y pues buscando nadie lo ha hecho aun y vi en el furum de Rasberry pi que alguien en enero comento sobre que monto con el Adapter que aquí muestras y que no arrancaba el sistema hasta que le siguieron comentado y compartieron la página de pimoroni donde hablan de las que si se pueden usar y escribió que mando a buscar una Samsung 960( lo cual se me hizo raro pues en la página mencionan la 980 y 980pro) pero según su último comentario dice que le funciono y pues voy a ir a comentarle a ver si contesta y cuenta su experiencia pues como te digo nadie aun lo ha documentado aun solo muestran la montura. En fin aquí un seguidor y admirador de tú trabajo y como te dice lo explicas completamente claro. Saludos desde la isla del encanto 🇵🇷☀️🏖

# shutdown -h now

There's no reason you can't have a desktop environment and run open media server...

@codefallacy

Ай бұрын

when i tried it a while ago with a raspberry pi 4 the install script failed maybe it gas changed since then

Obviously he hasn’t read the reviews about this Samsung SSD. I advise anyone who is looking to get one to do their homework

@codefallacy

3 ай бұрын

i already had this SSD months before the raspberry pi 5 was announced. i was using it on a computer and worked fine. what are some issues users should be on the lookout for?

why I can't boot pi 5? I just returned stupid thing

@codefallacy

5 ай бұрын

hey! if it didnt boot from the factory it was probably Dead on Arrival (DOA) and you are within your rights to return it if that is the case. if you get a new one let me know how it goes