It's a good idea to check oil pressure this after doing oil change. ●Slightly loosen the oil gallery bolt 1. ●Start the engine and keep it idling until engine oil starts to seep from the oil gallery bolt. If no engine oil comes out after one minute, turn the engine off so that it will not seize. ●Check the engine oil passages, the oil filter cartridge and the oil pump for damage or leakage

U guys have some good vids.

@Hunters_Mechanics

6 жыл бұрын

Thank you!

great vid thanks

About time!... A video without someone blabbing shit and only wanting to listen to the sound of their own voice... Good vid.. Good on ya!.. 👍

I have no idea where the stuff is, I don't see two holes I see a big metal plate on the bottom

Nice video.

What size copper washers ?

My second drain plug is stripped any tips on how to get out the old oil without drilling the bolt

@Hunters_Mechanics

2 жыл бұрын

Do you have a piggyback in the hole because the hole is stripped or do you mean the head is rounded off and you can't get it loose?

Hi i love your 660 raptor videos. i have a question do you know what size hole is the right side oil gallery plug bolt? its on right side of head with a phillips screw sealed by a copper seal. i would like to install a 1.5 inch dia oil pressure gauge.

@Hunters_Mechanics

2 жыл бұрын

I belive it's an M6 bolt

@Denkha94

2 жыл бұрын

@@Hunters_Mechanics would a 1/8 npt fit in?

@Denkha94

2 жыл бұрын

@@Hunters_Mechanics ok thank you

Is it necessary put a little bit oil in the oil pan? In total you put 2.3L is it the amount that should be?

@Hunters_Mechanics

5 жыл бұрын

When you drain the oil in anything, theres always still a little bit of oil left in the oil pan and there is still oil on all the parts so its not necessary when doing an oil change, and if you change the filter like I did, the total amount of oil you use is 2.3L

@Elmo10018

5 жыл бұрын

@@Hunters_Mechanics thanks bro

Nice video hey I'm flushing the coolant how many ft pounds do I tighten the 8mm bolt with copper washer on water pump?

@Hunters_Mechanics

3 жыл бұрын

drive.google.com/file/d/0BxP0yghvEhcHMEQwcnRFLTNzUEk/view?usp=sharing I'm not going to go searching for ya, but here's the entire manual for any future torques you may need!

@ricardodelriego4013

3 жыл бұрын

@@Hunters_Mechanics thank you 👍

Hi any advice on how to remove standard oil filter without the special tool?

@Hunters_Mechanics

5 жыл бұрын

Use can use an old leather belt that you dont care about, wrap it around and make a punch hole for the pin to lock it in and use it as a band wrench

@abdilraufdogan4982

5 жыл бұрын

@@Hunters_Mechanics thx buddy il give it a go tommorow morning

I hear some engine chatter mine does the same thing an runs fine just re adjusted the valves to .10mm an same sound is that just a normal Yamaha noise sir?

@Hunters_Mechanics

2 жыл бұрын

I would have to be there in person to hear it, can't just say its normal or not even if its over the phone lol if your valves are adjusted to spec, got plenty of oil and its running fine then I wouldn't stress about it unless it's an insanely loud clattering

@AnythingthatRuns

2 жыл бұрын

@@Hunters_Mechanics I was just curious sir thank you,! And I religiously change the oil an what not it runs fine no power issues i just thought I would ask sir ! Have a blessed day

I noticed you run k&n 303 what's the difference between it and the 147.

@Hunters_Mechanics

4 жыл бұрын

I honestly couldn't tell you, when I went to Autozone, we searched up a filter for it and the 303 came up saying it was used for a grizzly 660 (which is a very identical engine) and I tried it and it worked, so since I can find a 303 on almost every shelf, even at Walmart, I just use it lol

@johnstamper2965

3 жыл бұрын

The 147 is a shorter filter. The 303 is actually an automobile filter

Does it matter if you use kn1-147 or what’s the difference

@Hunters_Mechanics

2 жыл бұрын

You can use any filter that say it'll fit it, I bought this K&N one because I punctured a hole in a different brand that a weak shell material (almost like Fram's, real soft) so I buy this one since the shell is much harder. Haven't had an issues with it

👍👍

What is the best way to check oil level hot/cold

@Hunters_Mechanics

Жыл бұрын

Definitely hot, when its cold, the oil will sit in the case and not give you an accurate reading

Bro what oils did you drain?? I saw you drained 2 oils from different locations. I just bought an 02 Raptor 660 and want to service it myself. Also can you specify everything you used like what oil viscosity, brand, air filter, oil filter, costs etc. Thanks in advance

@Hunters_Mechanics

4 жыл бұрын

There's an oil reservoir tank that I drained first, that's where you will be filling up the 4 wheeler when the oil has been drained out, then the engine itself secondly. I use Yamalube 10w-40 (that you have to buy at a dealer or on amazon), I use a k&n oil filter because they have a much harder filter shell, I had a cheap one get hit with a rock and get a hole in while riding so I've used this one since and had no issue (kn 303 I believe), and the air filter is some cheap one I got off eBay because I had no money at the time and I also ride decently clean to not to worry about it at the moment lol

@lightningvolt1273

4 жыл бұрын

Hunter's Mechanics Okay cool, damn thanks a lot man you make it look really easy now it’s for me to give it a shot. Thanks again👍🏼👍🏼👍🏼

@LivanGonzalez14

2 ай бұрын

Bro I’m feel everything you said 😭😭

I have a 2005 raptor 660r but idk what oil to use?

@Hunters_Mechanics

4 жыл бұрын

Use 10w40, and preferably oil that's specifically made for ATV's because the oil soaks the clutches and you don't want them to slip!

@ashtonpetro2936

4 жыл бұрын

@@Hunters_Mechanics thank you cause I just bought it from someone a couple of days ago and idk if the ever did a oil change before so I wanna do that before something bad happens

@ashtonpetro2936

4 жыл бұрын

@@Hunters_Mechanics also I looked up 10W-40 to buy some but there was like 100 brands are they all the same if there for quad or do u have a brand that u like?

@Hunters_Mechanics

4 жыл бұрын

@@ashtonpetro2936 I just use Yamalube because it's specifically the brand name fluid of the 4 wheeler, I really don't trust anything else for a wet clutch situation other than the manufacturer of the engine

I have a 2004 Yamaha 660 what oil does it use??

@Hunters_Mechanics

3 жыл бұрын

Same as the other years, 10w-40 or 20w-50 depending on the temperature of your location. I run Yamalube in mine

@Fabian-zd9rn

3 жыл бұрын

@@Hunters_Mechanics Alr thx

Bro, what oil specification do you use?

@Hunters_Mechanics

5 жыл бұрын

Like viscosity?

@Elmo10018

5 жыл бұрын

@@Hunters_Mechanics yep and, is it a synthetic, semi-synthetic or mineral?

@Hunters_Mechanics

5 жыл бұрын

@@Elmo10018 I run 20w50 for Summer and 10w40 in the winter and I use conventional, I read some where that synthetic causes the starter clutch bearings to fail quicker so I just run conventional

@Elmo10018

5 жыл бұрын

@@Hunters_Mechanics yea i read too about to problems in the clutch when use the synthetic, thanks man again.

Clean the filter in oil tank as well

@Hunters_Mechanics

6 жыл бұрын

noel orourke I cleaned mine my last change and didnt think about, good catch

@camerongallant1125

3 жыл бұрын

How do you clean this?

@miguelgarcia-vg1fh

3 жыл бұрын

@@camerongallant1125 remove 2 hex nuts on button if the oil tank

@joshbirtchetfishing5196

3 жыл бұрын

U got a video of doing a coolant flush?

Should be using wix filters way better than k&n

@Hunters_Mechanics

4 жыл бұрын

Didn't even know Wix made an oil filter for this 4 wheeler

What oil is it

@Hunters_Mechanics

5 жыл бұрын

I use yamalube 10w40

How often you doing oil change?

@Hunters_Mechanics

5 жыл бұрын

I do it after 2 long rides, typically I go out for a ride around 5 hours so by the time I get in 2 rides its pitch black oil so I change it

@Hunters_Mechanics

4 жыл бұрын

@ already in the process of it

Are the 2 drain bolts the same size??

@Hunters_Mechanics

Жыл бұрын

They are not

@rubenbravo6794

Жыл бұрын

What sizes are they? I want to replace both of mine.

Bro wash your fucking quad... Never spray carb cleaner in a filter housing... Never do an oil change on a dirty engine at the risk of getting it inside the engine... Never rev a bike after the oil change due to the oil not fully lubricating the entire engine straight away (no oil pressure).... Pull the plug lead off and crank the engine a couple times to allow the oil pressure build up and then start it up ... job done

@Hunters_Mechanics

5 жыл бұрын

Bud I never sprayed it in the filter housing, the manual SPECIFICALLY STATES: Rev up the engine 3-5 times then shut it off, read one

@Hunters_Mechanics

5 жыл бұрын

You've obviously never worked with an engine to realize that brake clean won't hurt an engine at all, and I avoided just spraying it directly into the engine

@psycho3344

5 жыл бұрын

@@Hunters_MechanicsI have stripped more engines than you have had hot meals, you 'didn't spray into the housing' I smell bullshit. .

@Hunters_Mechanics

5 жыл бұрын

Doubt it

@psycho3344

5 жыл бұрын

@@Hunters_Mechanics no manual states rev up a engine that's just had an oil service you idiot... you will be posting videos on destroyed bottom ends next...

Chill with how tight you put it on lmao

@Hunters_Mechanics

5 жыл бұрын

I've had one loosen up and leak oil everywhere, I take precautions lol