Thank you for the video 👍 I have to replace a leaking gasket from previous owner

Great video. 😊

What size is the middle bold for he flywheel remover? I ordered it but didnt come with the middle part wanted to see if i can find one somewhere

Ive been trying to tackle the starter clutch on my 09 Raptor 250r. Ive gotten far enough to where im at use of the flywheel puller step. My puller i got which was supposed to be equivalent to the Yamaha puller, ended up being to small of a diameter. WHERE DID YOU GET YOUR flywheel PULLER?

Cool. Vid even cooler pup.

Hey I have a 03 660 in I need to replace the second gear in shift fork ..is this something I can do at home

That’s the right one it’s updated bc one u took off are bad from factory!!

Just ordered my throttle cable,starter clutch and manifold boot should I upload a how to repair video

i have a problem with my 660R but it wont get the clutch i go new discs for the clutch and it still wont

I did the repair it ran fine for 10mins then the screws snapped again do you think it's just cheap screws?

You gotta see it threw my boy 🤣 that last screw

I put mines in the shop to fix it worked for a while and started doing it again is there any starter clutch you can buy that can eliminate this headache in the long run???

@markchapman8101

5 жыл бұрын

I am sure there is a better (more expensive one). But I used an ebay one and haven't had the first issue.

Could you tell me the diameter of the puller and bolts thread size ? I can’t buy one right now so I’m going to try throw one together with what I have. Thanks

@markchapman8101

5 жыл бұрын

I dont have it anymore. Sorry!

I know its an old video but I have to order one soon. I need 04- 05 Curious what brand and where you bought?

@markchapman8101

6 жыл бұрын

Don't get me lying, bought it off eBay tho.

@kevinomarrivera1253

3 жыл бұрын

@@markchapman8101 bro did you flush oil first or you dont have to??

Why the dog couldn’t help 😞

How much does it cost to do to do a job like this

Bro que le hiciste al bendix 2005

So what was the reason behind the changing of your starter clutch? I've watched lots of these and nobody says "WHY" Were you having issues pulling on the starter rope recoil? Was the starter making making a noise when being engaged? Even with the spark plug out of the head was this engine very hard to turn over by hand??

@fortnitemobilevidvid9643

2 жыл бұрын

It will not start or crank at all that’s y you replace it

@Smalltechguy

Жыл бұрын

@@fortnitemobilevidvid9643 My grizzly still cranks but it's making a slight noise when the start button is pressed, so the starter one way clutch bearing is starting to fail. I've just ordered one so I'm going to tackle that in a few weeks.

Hey man I like that you made a video how to do it but plz do not ever say 5/16 or 8 mm bc one those are 2 different sizes might be really close but if you use the wrong one you will strip the head of the blog and some times that can be a beatch

@kauaisfinest14

5 жыл бұрын

Bryan Mcmorris as soon as I heard him say that I came to the comments to let him know to lol.

@jimthomas522

5 жыл бұрын

You’re correct. 8mm and 5/16” (7.94mm) are different sizes. That’s a .06 difference and my guess is most sockets of the same brand have more of a variation than that .06mm.

@kingstoner5459

4 жыл бұрын

My manual says either or will work

@johndaviddoesmith4504

11 ай бұрын

There are several sockets that are almost if not exactly the same size this being one 19mil and 3/4 being another… they’re so close a lot of times you will only get one or the other in a cheap set of wrenches

Amigo ocupo el vendis y la estrella que ba atras del macneto de una yamaha raptor 660 2001 cuanto vale podras darme una idea plis

@andressierra2780

2 жыл бұрын

En Amazon está disponible

i wasnt able to impact off the big nut on the clutch... mf wont break... any tips or insight?

at min 11:42 what is the name of the smaller circle that was taken off?

@markchapman8101

7 жыл бұрын

Katya Arreguin that is the starter clutch.

@katyaarreguin4320

7 жыл бұрын

because a friend of mine wants to fix his 4 wheel motocycle but he doesnt speak english so he asked me to translate the video so he could know what that was, what function does it have ?

@markchapman8101

7 жыл бұрын

Katya Arreguin if he can not crank his 4wheeler by the clutch and the starter button on the left side of the handle bar (but he can push start it) the culprit is the starter clutch

Is it a reverse thread on the clutch starter?

@markchapman8101

5 жыл бұрын

I am not 100%. I would thinks so though. Consult a repair manual or local Yamaha dealership. Or google!

@paulbykov7750

5 жыл бұрын

MoneyPit Garage it is not!! Broke the damn crankshaft because torqued in the reverse direction!

@moistnuuget6997

4 жыл бұрын

@@paulbykov7750 damnnn rip.

I I just got my grandpa's 66003 starter clutch done and the guy is charging me $600 I think that's too much

Obviously. I could use your help with an 2002 660

@markchapman8101

5 жыл бұрын

What can I help ya with?

rip headphone users 1:00

"These right here on the starter is an 8, or a 5/16"

do you need to drain the oil

@coolace900aj

6 жыл бұрын

yes

@markchapman8101

6 жыл бұрын

No sir.

@reynaldogarza4225

4 жыл бұрын

Yes or no?

02-05 are all the same the year doesn’t matter

“An 8mm or a 5/16”…. I left the vid

thats a woodruff key

Real home mechanic's hands....bloody, lol

@markchapman8101

7 жыл бұрын

UK5098 no other way. besides I wear gloves at work due to blood born pathogens and all. lol! nice to let them breath. thanks for stoping by.

Mark chapman? that's a famos name (-:

@markchapman8101

5 жыл бұрын

🤣🤣🤣

Thats not the clutch thats the flywheel.

There's a real simple way to get the magneto off the tapered end of the crank without having to put alot of pressure on the puller. Put a few lbs of force on the puller and then give the head of the center bolt a couple moderate taps with a ballpeen or mini-sledge, it will always pop off in short order.

@markchapman8101

7 жыл бұрын

Nero Fluidis elaborate!

@nerofluidis9282

7 жыл бұрын

There's really not much to it. 1) Put puller on 2) Tighten puller with a moderate amount of torque (15-20ft lbs to start) 3) Take hammer, give the center bolt that is pushing on the crankshaft a decent few taps with the hammer (*you don't need to hit it very hard*, the point is to send vibration down the bolt which will translate to the shaft and break the friction seal that is holding the magneto to the tapered end) 4) If it doesn't work the first time, tighten the puller a bit more (another half-turn or so) and do it again When it does work, the magneto will simply pop off with relatively little drama. What's great about doing it this way is that you don't need to tighten the crap out of the puller to get it off, meaning you don't have to worry about stripping the threads in the magneto, which for some reason Yamaha made quite shallow and therefore weak. The other benefits are that you won't risk mushrooming the tapered end of the shaft. I've done several Raptor mags this way and a half-dozen on other machines and it's far easier/less risky than using sheer force to pull it off.

@markchapman8101

7 жыл бұрын

Nero Fluidis I gotcha! what you missed (due to editing in order to keep vid to 15 minutes) is where I tried the hammer and then an impact and it didn't budge. Therefore resulting in my brute force, lol.

@nerofluidis9282

7 жыл бұрын

lol ah I see

@markchapman8101

7 жыл бұрын

Nero Fluidis yea unfortunately I can only load up to 15 minute videos at a time, so it forces me to cut out uneceassary stuff unfortunately.

what a horrible video....