I found this video one day too late.. but i still watched it to make sure i didnt miss anything. I got a tip from an old mechanic that id like to add here: Before cracking it up, run it in a ultrasonic cleaner at 70'c for a couple of hours. This makes the gaskets come loose easier. This video works just as good for a yamaha grizzly 350 2007. Also behind the cap you didnt open there is a springpressured steelball that can get clogged. This prevents the atv from backfiring when you turn it off. Thumbs up..

Great teaching video, by the time you finish, I finished and had two beers, Thanks👍

@ils360

2 ай бұрын

Glad you enjoyed and I'm glad I could help 😁

Extremely helpful. I had the exact same carb and needed to know how to clean it.

@ils360

7 ай бұрын

I'm glad I could help 🙂

Great video. I used it to clean and reassemble one today and got it right the first try. Thank u

@ils360

Жыл бұрын

So glad that the video came in handy for you that's why I love making them Love helping people out wherever I can

Thanks bro i will follow this video to the t and try to clean my very first carburetor

Great info , Should help some folks out man !

@ils360

2 жыл бұрын

Yeah it's my goal I hope it'll help somebody out give them the confidence to pull theirs apart and clean it out and save some good money

@shawnmrfixitlee6478

2 жыл бұрын

@@ils360 right on..

I’m glad I seen how to clean a carburetor the right way.That’s a raptor 700 carb right?

Great video

@ils360

3 ай бұрын

Thank you! 😊

At 23:11 you take out another jet or whatever, my carb has almost like a cover on it that just has a pin hole, how can I get that off to get to the point I can use a flat head to remove it?

Hey man great info. I’m struggling to connect my choke when I’m putting a new carb on my raptor 350. I’m not sure if my new carb is different or not but it looks the same as the original. Where the choke cable goes into the carb how do you connect it inside?

@ils360

Жыл бұрын

If it is the barrel style there is a little slide that needs to come out for you to lock the cable on to it and slide it back in.

@kalebwhalen7896

Жыл бұрын

Would there be a spring in front of the part that comes out? How do you remove it?

My raptor 350 pops out the exhaust when I turn it off. What could it be? And it also only runs with some choke.

@ils360

Жыл бұрын

Definitely sounds like a dirty carburetor having to run it with some choke. The backfiring could be caused by the same or there could be a lot of carbon build up in the cylinder.

Hi I’m leaking fuel out the over flow and will only stop when fuel is turned off. Carb has been taken apart and cleaned well but still have the same problem. Iv checked the float needle etc raptor 250

@ils360

Жыл бұрын

Check the float and make sure it's actually floating Make sure it's not filled with fuel. Then check your needle and seat making sure that there's nothing up inside behind the seat he also might need to remove and check the needle seat itself there's an o-ring that goes around it and if it is torn it won't meter fuel if you're still unable to find anything you might need to just buy a new needle and seat and replace it as a unit

At 9:20 the piece you are holding that came out with the float. The needle in it moves on mine but the whole entire piece is stuck in the carburetor on mine

@ils360

Жыл бұрын

Soak it with lots of carburetor cleaner try cleaning out the varnish on either side with a little pic or sewing needle or something that you can get in there without scratching continue to soak with carb cleaner until you can get it to move. Might just have to buy a new needle and seat for your carburetor Make sure you buy the same size there's actually larger and smaller ones for some carburetors

How did you put that silver nozzle at 29:30 back in ? I dont know how hard can I push it and I cant get it back in...

@ils360

Жыл бұрын

That was definitely a hard one to get back in that has to be perfectly lined up straight to go back in.

@viliamjakab6158

Жыл бұрын

@@ils360 right, and do I just push it in hard with a screwdriver ?

@ils360

Жыл бұрын

@@viliamjakab6158 if you've got something flat to put across it it would work best like a punch or something like that. You can also likely tap it to get it to move

So I have been cleaning it the wrong way?🤣

@ils360

Жыл бұрын

I don't know how have you been doing it? 😂