I'm about to use jb weld extreme heat , same stuff just premixed, to fix small oil leak from chip in bottom crankcase on GSXR 750 , after seeing your video i'm sure it will work for me also, thanks for sharing mate.

@ninjarider2718

Жыл бұрын

Did the jb weld work on your bike?

@allthingsandmore4613

Жыл бұрын

Did it work?

I used this for a bad fuel leak on my ZX6R. No more leaks!

i found a similar leak on my bike, i used jb stik weld jus now , waitin for it to dry. hope it holds . it leaks lesser oil than what yours puked but i just cleaned up around the area and applied the stick weld.

@allthingsandmore4613

Жыл бұрын

How did it work

@JimCamel37

Жыл бұрын

@@allthingsandmore4613 good. so far it is holding up!

Better yet would be to use an aluminum welding rod. You can use these rods with a butane torch to fix or patch aluminum.

I'm about to use it on my 929rr block where it meets the stator cover on the bottom

@Theunprogrammed1

Жыл бұрын

How’d it go bro same thing happened to me

it is now 2019, is the JB weld still holding?

I used crazy glue and baking soda on my cbr600 stator cover. Its still holding.

@daydaydful

4 жыл бұрын

intelin123 are u for real cuz my stator cover is leaking and I’m at wits end would jb weld be better then Kraft glue and baking soda ??

@daydaydful

4 жыл бұрын

I also have a cbr 600

@brandonatkins9087

3 жыл бұрын

Got a cbr1k and I'm going to try this on my oil pan. Have you guys tried this?

@eman85mph

2 жыл бұрын

@@brandonatkins9087 same but R1, damn gaskets are CRAP these days bros

@brandonatkins9087

2 жыл бұрын

@@eman85mph I ended up getting mine welded bro best $40 I've spent

Patching up an oil leak on my Harley's engine case which has a hairline crack. Looks like it will hold. Do you have to sand the JB Weld before painting it?

@azzkam8972

6 жыл бұрын

Joey Gabagool iv not painted mine yet it does set really smooth and flat a coat of primer should do the job.

my air cooled bike is leaking along the crankcase gasket at the bottom, would JB weld hold?

@azzkam8972

6 жыл бұрын

ApolloR1der I have no idea bro but it’s worth trying I reckon

That part of the engine does not get extremely hot though.

did this hold up? mines is the same but it is litteraly a hairline crack after sliding along the road so was thinking of trying this.

@azzkam8972

7 жыл бұрын

Michael Mcmillan still going strong mate

@michaelmcmillan8814

7 жыл бұрын

Azz Kam perfect I'll give this a bash at the weekend. thanks

Any chance you can send me the link for it please I need some for a zx6r crank case rite at the bottom side where it slid please

@azzkam8972

4 жыл бұрын

amy rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F223492345234

You think this will hold up agaisnt coolant on my oil cooler? Few small holes from screwdriver removing the oil filter

@azzkam8972

4 жыл бұрын

Definitely worth a try mate

@spartacus09ful

4 жыл бұрын

@@azzkam8972 Cheeers, is yours still holding up? assuming you still have the same bike

@azzkam8972

4 жыл бұрын

Damo C yup still have the same bike and still holding up

@spartacus09ful

4 жыл бұрын

@@azzkam8972 Impressive, Cheers

@spartacus09ful

4 жыл бұрын

@@azzkam8972 Used it on the cooler and so far so good, Only ran it once so far (not a ride though due to lockdown) but fingers crossed it holds. It sets stupid tough. Cheers for your video I'd have never thought of using it.

Did it work my ktm I took the head of has a crack at the on top its leting water in do you tink it will work

@azzkam8972

6 жыл бұрын

macker b mine is still fully sealed not sure about your issue but if I were you I’d definitely give it a go! Once it hardens it is rock solid.

@dbdb4274

6 жыл бұрын

Azz Kam Mine is just leting water In to my cylinder at the piston smallest crack... Someone glued it before me and had it for a few weeks what one did you use what's it jb weld what... I seen the putty it was shit

@azzkam8972

6 жыл бұрын

Yup jb weld

@dbdb4274

6 жыл бұрын

Azz Kam witch jp weld did you use there's a few of them

@azzkam8972

6 жыл бұрын

macker b not sure of the specific name but the pictures the beginning of the video I got two tubes one with a grey paste and one with a black paste and you have to mix them both together.

Update on jb weld ?

@azzkam8972

4 жыл бұрын

Hella Naughtyy still good bro

@tommy_bluewolf2865

4 жыл бұрын

I have a zx10r an it has a hairline crack between crank case and trans , leaks oil consistently but not aggressively . Going to attempt the jb weld . Have you been riding aggressively after the jb weld ? Because I’m a pretty aggressive rider I’m just thinking if this is going to be a permanent fix

@azzkam8972

4 жыл бұрын

Hella Naughtyy pretty aggressive but mine was a small whole a crack is different because the can spread but Its still worth a try

@fers2053

4 жыл бұрын

is it still fixed? 3 years fixed??

Is it still fixed 2020???

@azzkam8972

4 жыл бұрын

F Santos unfortunately not done much mileage in 2019/20 but still fixed yes.

@fers2053

4 жыл бұрын

Thanks

is it still fixed?

@fers2053

4 жыл бұрын

Sorry I don't speak good english, is it still fixed?

@fers2053

4 жыл бұрын

???

jb weld is a bit pricey but man does it do what it is supposed to do no problem

@joeygabagool3066

6 жыл бұрын

PRICEY???? It's less than 5 bucks at Walmart

@dbdb4274

6 жыл бұрын

It's 10euro in Ireland that's not much I give that to my kid for sweets

@blakexcrum

3 жыл бұрын

$5-$10 is pricey?! What’s the cost of not being able to ride on two wheels for you Ian?! 🤔😝😆