How to properly install wheel bearings on your harley davidson
Жүктеу.....
Пікірлер: 48
@L.K.S.R.4 ай бұрын
Hearing them wrenches drop on that sealed concert reminds me of my time at MMI in Phoenix.
@redgeypedersen414 жыл бұрын
What brand of bearing tool do you use?
@MrJohnnebgood2 жыл бұрын
You don’t put any grease on bearing before installing? Also I at start of video you pulled from pulley side and the puller shaft you have seems much longer than what I have. Couldn’t get mine to work.
@tomanguish64072 жыл бұрын
Freeze your bearings before installing. They almost fall in.
@skipjack59644 жыл бұрын
Did he put any grease on that there bearing thing
@TheATVboy172 жыл бұрын
nice vid
@fearingforamerica9217 жыл бұрын
I'm pretty sure you put the primary bearing in first untill ot bottoms in the wheel. disc side is primary. then you put spacer in and other bearing until it touches the spacer. none the less. you're not using a hammer good job
@robertpolo4554
3 жыл бұрын
What about front, matter which installs first?
@Dan-rc4cx
3 жыл бұрын
On the rear wheel you should always install the brake rotor side bearing first. On the front you should always install the bearing on the side that does not have the axle nut first
@bisharajoseph63
2 жыл бұрын
@@Dan-rc4cx Why ?
@johnkessler7820
Жыл бұрын
Absolutely correct, what you said. Just like the shop manual tells you what to do.
@johncasor9698
Жыл бұрын
@@robertpolo4554 yes
@gshoaf15 жыл бұрын
Dang, I thought I recognized your voice, then I saw South Main Customs.
@elieli83683 жыл бұрын
The bearing tool brand or part number please.. Thanks
@mobilegarage93122 жыл бұрын
What is that tool called or where can we buy it?
@bruceblackerby37428 ай бұрын
No distance collar installed between the bearings?
@nojustice83533 жыл бұрын
so you dont have to lube the outside of the bearing...???
@mcspr213 жыл бұрын
What is the name of the tool???
@_2wheelsmovesthesoul_619 Жыл бұрын
Nice video, do you have to set end play on these 3/4" sealed bearings like you do the 99 and older timken?
@AMDcycles
Жыл бұрын
No , you do not
@blackonepac3 жыл бұрын
Gd job!!!
@gregmeeks27539 ай бұрын
where do i get that tool please ?
@user-qc5iq9gu1pАй бұрын
I always use a mom n pop shop when i cant fix it myself. Never a stealership
@gillardpetry74922 жыл бұрын
Where is your shop located? Also, could one make a bearing tool with all the proper materials?
@zeldaoftime
6 ай бұрын
AMAZON BRO
@whollymary74062 жыл бұрын
We can’t really see what you are doing cause of the placement of the camera your working on the other side of the wheel we can’t see it BUT we can take your advise thank you
@jeffdurocher86692 жыл бұрын
The dealer is telling me there are 3 bearings in the rear. 2 on the belt side and 1 on the right(abs) side. Is this true?
@bisharajoseph63
2 жыл бұрын
only 2
@finley614
2 жыл бұрын
If you have a abs with the isolated drive system in rear pulley you will have 3 bearings in the rear total.. I have the 08 Anniversary Ultra with abs and there is a bearing for rear belt pulley and then behind that pulley there is a wheel bearing ( this is all on left rear) then on brake rotor side ( right side) rear behind the rotor is another wheel bearing
@rolandos643 жыл бұрын
Why is it a throw away bearing when removed w proper tool?
@JeffinTD
3 жыл бұрын
Ball type bearings can be damaged when a high load is put on its axis. When you pull the bearing, you are pulling by the inner race, against the interference fit of the outer race in the bore. Once removed the bearing might not immediately seem bad, this likely damages the balls and sets the gearing up to fail. Pressing in the new bearing, the pressing force should only be applied to the outer race. It is also important that the bearing be fully seated in the bore. Otherwise, when installed in the motorcycle and the axle is tightened, the axle will force the bearing the rest of the way in via the inner race, again damaging the bearing.
@johncasor9698
Жыл бұрын
maybe old. you should replace bearing like evey 20k and check them every 10k... i do this every tire change so it is like 8k for me...
@Dan-rc4cx3 жыл бұрын
Not proper procedure shown. On the rear wheel you should always install the brake rotor side bearing first. On the front you should always install the bearing on the side that does not have the axle nut first
@spelunkerd
2 жыл бұрын
Why?
@alexbouchard3880
Жыл бұрын
Because if you bottom out the pulley side first they won't be in the right position laterallly
@user-hq4xp9ye6t
11 ай бұрын
The guy is a hack, but talks a good story.
@timmonthygriffin57073 жыл бұрын
Can a impact be used to put bearings in?
@johnkessler7820
Жыл бұрын
You will eventually chew up the threads on your bearing tool
@timmonthygriffin5707
Жыл бұрын
@@johnkessler7820 thank you
@johncasor9698
Жыл бұрын
never use a impact tool on any puller ever. you want the part to move slowly in or out believe me...
@johncasor9698 Жыл бұрын
AT 1:16 WHY DO YOU IN STALL THE 2 BEARINGS WITHOUT THE CENTER SPACER ??? YOU SHOULD KNOW BY NOW TO INSTALL THE SPACER ??? AND WHAT ABOUT THE SPACER CORRECT LENTH ??? YOU MUST ALWAYS CHECK THAT BECAUSE YOU DO NOT ALWAYS KNOW WHAT CLOWN WORKED ON THIS WHEEL BEFORE YOU AND JUST TOSS IN WHATEVERY SPACER LOOK GOOD??? A MASTER TECH WOULD PUT A LITTLE GREAS ON THE BEARING OUTER EDGE AND THE THREADS OF THE TOOL TO HELP MAKE THE JOB GO MUCH EASIER ... JUST SAY`N... YOU REALLY DO NOT WANT ME IN YOUR SHOP IF YOU SHOW YOUR INCOMPETENCE ON FILM FOR THE PUBLIC TO SEE, I COULD NOT IMAGINE WHAT YOU DO OFF CAMERA ... i am a Master Aircraft Tech for the Government for many years and everything i do is checked and rechecked no mistakes allowed ever when i make mistakes people die, and what you are doing here is the same thing people could get hurt too if you make mistakes you really need to teach better, like the width of the bearing you are installing is correct??? you should state that they are different on some bike hubs some take a 3 millimetre wider .125 '' on one side for Anti-Lock brake hubs... i have a friend that rear wheel locked up 4 times at very high speed like 90 MPH before a tech noticed the wrong bearing width was used causing the bearing to shift positions and some how fail and lock up..
@jackmehoff5523
11 ай бұрын
Really.....four times his rear wheel locked up at 90 mph and he lives on to tell about it? He must be one incredible rider.
@Bleriotman2 жыл бұрын
You started the video 5 minutes too late. HOW DO WE REMOVE THE BEARING PROPERLY!?!?!? We have to do that before this video becomes useful. Thanks! .
@johncasor9698
Жыл бұрын
just buy the wheel bearing tool and read the instructions... it is elementary a 12 year old could do it.. i was like 13 when i was changing out wheel bearings and tires...
Пікірлер: 48
Hearing them wrenches drop on that sealed concert reminds me of my time at MMI in Phoenix.
What brand of bearing tool do you use?
You don’t put any grease on bearing before installing? Also I at start of video you pulled from pulley side and the puller shaft you have seems much longer than what I have. Couldn’t get mine to work.
Freeze your bearings before installing. They almost fall in.
Did he put any grease on that there bearing thing
nice vid
I'm pretty sure you put the primary bearing in first untill ot bottoms in the wheel. disc side is primary. then you put spacer in and other bearing until it touches the spacer. none the less. you're not using a hammer good job
@robertpolo4554
3 жыл бұрын
What about front, matter which installs first?
@Dan-rc4cx
3 жыл бұрын
On the rear wheel you should always install the brake rotor side bearing first. On the front you should always install the bearing on the side that does not have the axle nut first
@bisharajoseph63
2 жыл бұрын
@@Dan-rc4cx Why ?
@johnkessler7820
Жыл бұрын
Absolutely correct, what you said. Just like the shop manual tells you what to do.
@johncasor9698
Жыл бұрын
@@robertpolo4554 yes
Dang, I thought I recognized your voice, then I saw South Main Customs.
The bearing tool brand or part number please.. Thanks
What is that tool called or where can we buy it?
No distance collar installed between the bearings?
so you dont have to lube the outside of the bearing...???
What is the name of the tool???
Nice video, do you have to set end play on these 3/4" sealed bearings like you do the 99 and older timken?
@AMDcycles
Жыл бұрын
No , you do not
Gd job!!!
where do i get that tool please ?
I always use a mom n pop shop when i cant fix it myself. Never a stealership
Where is your shop located? Also, could one make a bearing tool with all the proper materials?
@zeldaoftime
6 ай бұрын
AMAZON BRO
We can’t really see what you are doing cause of the placement of the camera your working on the other side of the wheel we can’t see it BUT we can take your advise thank you
The dealer is telling me there are 3 bearings in the rear. 2 on the belt side and 1 on the right(abs) side. Is this true?
@bisharajoseph63
2 жыл бұрын
only 2
@finley614
2 жыл бұрын
If you have a abs with the isolated drive system in rear pulley you will have 3 bearings in the rear total.. I have the 08 Anniversary Ultra with abs and there is a bearing for rear belt pulley and then behind that pulley there is a wheel bearing ( this is all on left rear) then on brake rotor side ( right side) rear behind the rotor is another wheel bearing
Why is it a throw away bearing when removed w proper tool?
@JeffinTD
3 жыл бұрын
Ball type bearings can be damaged when a high load is put on its axis. When you pull the bearing, you are pulling by the inner race, against the interference fit of the outer race in the bore. Once removed the bearing might not immediately seem bad, this likely damages the balls and sets the gearing up to fail. Pressing in the new bearing, the pressing force should only be applied to the outer race. It is also important that the bearing be fully seated in the bore. Otherwise, when installed in the motorcycle and the axle is tightened, the axle will force the bearing the rest of the way in via the inner race, again damaging the bearing.
@johncasor9698
Жыл бұрын
maybe old. you should replace bearing like evey 20k and check them every 10k... i do this every tire change so it is like 8k for me...
Not proper procedure shown. On the rear wheel you should always install the brake rotor side bearing first. On the front you should always install the bearing on the side that does not have the axle nut first
@spelunkerd
2 жыл бұрын
Why?
@alexbouchard3880
Жыл бұрын
Because if you bottom out the pulley side first they won't be in the right position laterallly
@user-hq4xp9ye6t
11 ай бұрын
The guy is a hack, but talks a good story.
Can a impact be used to put bearings in?
@johnkessler7820
Жыл бұрын
You will eventually chew up the threads on your bearing tool
@timmonthygriffin5707
Жыл бұрын
@@johnkessler7820 thank you
@johncasor9698
Жыл бұрын
never use a impact tool on any puller ever. you want the part to move slowly in or out believe me...
AT 1:16 WHY DO YOU IN STALL THE 2 BEARINGS WITHOUT THE CENTER SPACER ??? YOU SHOULD KNOW BY NOW TO INSTALL THE SPACER ??? AND WHAT ABOUT THE SPACER CORRECT LENTH ??? YOU MUST ALWAYS CHECK THAT BECAUSE YOU DO NOT ALWAYS KNOW WHAT CLOWN WORKED ON THIS WHEEL BEFORE YOU AND JUST TOSS IN WHATEVERY SPACER LOOK GOOD??? A MASTER TECH WOULD PUT A LITTLE GREAS ON THE BEARING OUTER EDGE AND THE THREADS OF THE TOOL TO HELP MAKE THE JOB GO MUCH EASIER ... JUST SAY`N... YOU REALLY DO NOT WANT ME IN YOUR SHOP IF YOU SHOW YOUR INCOMPETENCE ON FILM FOR THE PUBLIC TO SEE, I COULD NOT IMAGINE WHAT YOU DO OFF CAMERA ... i am a Master Aircraft Tech for the Government for many years and everything i do is checked and rechecked no mistakes allowed ever when i make mistakes people die, and what you are doing here is the same thing people could get hurt too if you make mistakes you really need to teach better, like the width of the bearing you are installing is correct??? you should state that they are different on some bike hubs some take a 3 millimetre wider .125 '' on one side for Anti-Lock brake hubs... i have a friend that rear wheel locked up 4 times at very high speed like 90 MPH before a tech noticed the wrong bearing width was used causing the bearing to shift positions and some how fail and lock up..
@jackmehoff5523
11 ай бұрын
Really.....four times his rear wheel locked up at 90 mph and he lives on to tell about it? He must be one incredible rider.
You started the video 5 minutes too late. HOW DO WE REMOVE THE BEARING PROPERLY!?!?!? We have to do that before this video becomes useful. Thanks! .
@johncasor9698
Жыл бұрын
just buy the wheel bearing tool and read the instructions... it is elementary a 12 year old could do it.. i was like 13 when i was changing out wheel bearings and tires...
@roadgliderider
8 ай бұрын
kzread.info/dash/bejne/l2F7krSCeau4epc.htmlsi=_ptkubcHHJ01nqOt