All you had to do was wrap Teflon tape around the end of the bolt fill hole with gear oil and hit it with the impact.The hydraulic pressure will pop it right off. No damaged threads. Also always grease the puller threads.

Thank you so much that was such a big help

What size is the big bolt and the thread pitch?

good job on all video's

Scary bro. Very close to destroying it but you got it, and yea ima oder the 15 dollar tool, and not stress, thanks tho for posting this

primary clutch suppose to have just a hair of wiggle when wiggled back and forth?

Will it start up with a bad clutch?

How to put the clutch back?

If it does damage thread just get a tap. An run a tap through it

Pleasee help, i did all of this yesterday and everything worked perfectly and great videos, but when i put the primary clutch on it rubs against the little rubber peace behind it

Any recommendations on what to try if the threads of the Primary are stripped? I tried tapping them but didn't work. I have a new clutch so I'm not worried about damaging it.

@RonDoiron-pz3ee

7 күн бұрын

Strip the clutch, use a puller, got it this way, no problem, tried the grease oil trick, didn’t work, made up a piece to go behind the centre nut, put the puller on, tighten, tap the end of the puller screw, out it came!! Had to rebuild that clutch anyway, so, dismantling it wasn’t a problem. I was able to clean up the helix, rollers were good, back in service!!

Do you see what I mean?Pushing on outside caused the washer to damage it slightly,luckily it wasn't worse?I have a '99 Sportsman500 and I am switching the Short Block(bottom end of engine) with a good,used one from a dealer but I couldn't find any video on R&R the engine?I got mine almost all apart,and I have the used engine,oh AND I have Factory service manuals for my model.Any idea where to look?Thanks for having this channel for folk like me!Take it easy!

@BigjermsGarage

8 жыл бұрын

I now have the real tool that was only $20 off ebay, much easier.

@williamcrane9289

4 жыл бұрын

@@BigjermsGarage Hey what would the tool be called exactly? thanks in advance.

@InutUrBuckeye

2 ай бұрын

@@BigjermsGarage What size tap did you use to repair the threads?

Is there a trick to getting the plastics off? Do I need to detach all the wiring?

lol sounds like Cant Stop by Red Hot Chili Peppers in the backround

Why not just "taper the tip of your tool/bolt/puller so it is able to be Recieved into the crankshaft?"If it were a Sharper point on the tool,it would be put right into the crank without any Damage..?!

Hey we bought a trailblazer and the threads are already messed up. What should we do?

@BigjermsGarage

10 жыл бұрын

I used a counter sink to clean up the outside edge and then a tap to fix the first couple threads. I believe the tap I used was a "12 -1.25, fine thread"

@jodydaniels3927

5 жыл бұрын

Tap it

Any common impact drill/driver (and the correct clutch puller which is available all over the Internet for a very reasonable price) will do that entire process in no time. You don't even have to hold the clutch in place. To remove that center bolt, just use an impact. Takes it off instantly. And just use a proper clutch puller to remove it. You can buy the clutch puller for these models for next to nothing online. (Totally worth it instead of destroying your parts.) Use your impact, the clutch pops right off. It is so easy it is not even funny. And I'm not even some 'professional' mechanic. What mechanic (backyard or other) does not even have an impact driver... Come on people. One of the most common - but HIGHLY necessary tools - for any mechanic. ....awful 'help' video

I have a 2003 polaris 250 trailblazer withno airbox. everytime I Bo through a mid puddle or water. it stalls an loses power momentarily. this shoudlnt be happening if its not submerged in water correct?

@TylerMohrTymo

8 жыл бұрын

mud might be going in the carb that would be the only thing I could think of

Bro any idea why my 250 trailblazer drop fuel from the manifold exhaust

@DS-mm6fh

3 жыл бұрын

Crankcase is prolly full of fuel

@hectorsanchez2146

3 жыл бұрын

@@DS-mm6fh that was the problem thank you 🙏

Wow, unreal. lmmfao

$35. Dollar tool save all that headache.

shoulda used bread