I like how he began using actual parts to help us easily understand his teachings. Thanks man.

I put new rings on a piston on my bike. I didn't measure ANYTHING. I was so pleased when I started the bike and it ran. It ran pretty well. I did 500 miles on it, including some quite tricky off-road stuff. It smoked a little. It smoked a lot. It used oil quicker than petrol. But it ran. I decided the oil use was more than your everyday break-in consumption so tore it down again and did some measuring. The rings I fitted were standard. I'd assumed the piston was standard. It wasn't. It was a full 1mm oversized. The piston ring end gaps were like the black hole at the centre of the universe. I'm still a bit baffled the bike ran at all, nevermind scrabbling up rocky mountain tracks and a few laps of a race circuit. '85 XT350. Love it.

@alistuslarter6787

3 ай бұрын

I bet you had good compression

The piston ring's end gap allows for expansion of the ring due to the engine heating up, much like adjusting valve lash in an engine with mechanical lifters. without the gap, the rings could start expanding outward into the bores and kill the engine. great videos btw, ive watched almost all of them and appreciate the condensed learning within them.,

@DTRU122283

7 жыл бұрын

Not to mention, on a performance engine the temps are usually higher which expands the rings even more. That is probably THE major limiter on how much nitrous an engine can take, given the tune is perfect.

@chasemiller7974

4 жыл бұрын

Not to mention also that without relief of the compression through those gaps, the piston rings could have a tendency to crack and fail.

You deserve so many more subscribers, the way you break things down and explain them is awesome. I love learning about and having the knowledge of why engines and processes work. Keep up the awesome work coming from someone interested in mechanics and mechanical engineering!

I appreciate these videos you put out, and explaining in such a way that the layman can understand. You are the Carl Sagan of mechanical engineering.

@Nalopotato

8 жыл бұрын

+mygreenzebra He's not nearly as poetic as Sagan =p Which isn't a bad thing, just a fact.

@EngineeringExplained

8 жыл бұрын

+mygreenzebra Some of you are too kind with your compliments! Really appreciate it, glad you enjoy the videos!

It truly is amazing how piston rings lasts so long in car engines these days. The amount of work they have done in high mileage vehicle and yet still have little to no compression loss or blowby must be a credit to good design and probably oils that look after these thin little bits of metal.

Finished watching all your videos explaining how cars work! Thank you for everything you've taught me, I basically knew nothing before I came across this channel.

Thank you man. Really good presentation. Like someone mentioned-thanks for using an actual piston along with your illustrations.

I would enjoy a video regarding valve seals.

No mention as to clocking the rings for proper ring position to ovoid excessive blow by? ( I learned more than I chimed in! Thanks! )

@MrTheHillfolk

8 жыл бұрын

I installed total seal rings before , and now blowby is minimal. I think I'd have em made for any engine I ever redo. It's also Good enough to have a open crankcase vent and not get gassed out by it inside the car.

I think your videos are awesome there are informative and thoroughly explained by yourself, but sometimes you go through quite quick in videos and i get a little lost & confused as im no engineer like yourself, but i am learning slow but surely..;) Thanks again for sharing your knowledge of engineering and mechanics, and please keep the vids coming. Peace.

my cousin and I are rebuilding a 1990 Mazda B2200 pickup. He thinks piston 3 is leaking oil into the combustion chamber, he can't be wrong because it looks nasty. I'm glad for videos like this and others that will be helpful as we continue with the rebuild.

Do a video on Subaru's new platform explained and how it matters to future owners

@Ndog888

8 жыл бұрын

I AGREE

Now, me and the mad scientist got to rip apart the block and replace the piston rings you fried.

Great video as always. Picking up where you stopped the video at....id love to see a video about worn piston rings vs carboned up ring grooves leading to rings no longer able to seal correctly. Basically, a comparison as to which is the actual culprit for blow-by. Much like how warped rotors is a generic term for uneven rotors, when the rotors are not actually warped.

Hey Jason, love your videos have almost watched them all, helped me so much giving me a visual example on some tricky stuff so thanks for that. Now, could you possibly do a video on stalling hydraulics in heavy diesel machinery, I have read a bit on it but would love to see you do a video on it to help me understand, thanks again!

Could you do a video on hard break-in of an engine vs soft break in please?

Wow! Technical automotive videos without an obnoxious introduction nor any irrelevant details such as what you had for breakfast or your most recent sikkk modz. Thank you sir, this is great! Subbed!

@EngineeringExplained

7 жыл бұрын

+jsamhall that's my style, glad you enjoy it, thanks for subscribing!

I was going to ask about Engine knock but then found your video from 2014.. Nice one lad, you have us nicely covered..

Although I already knew what piston rings do; I wanted to watch this video and it is as accurate and even better than I could have described their purpose! 😊

Could you could do a video on hard vs soft break-ins? Manufactures tell you to soft break-in engines, but since learning about glazing and ring seating I don't know who to trust any more. I feel like manufactures just tell you to soft break-in to cover themselves, even if it's worse for performance. But I wouldn't risk an engine on it without an experts opinion. Thanks.

@socas_nic

5 жыл бұрын

Break ins have to be soft. You want your engine to be used in all kinds of RPMs in different gear ratios. Also do not stay on to certain RPM for no longer than 20-30 seconds. Do not red line your engine and do not let it idle for more than 30 seconds. So generally use different gear ratios at different speeds while not going above the recommended RPM and while not cruising for extended periods of time.

@bernardlandymore7372

4 жыл бұрын

Soft break in is the way to go if you have built the motor your self. The first 50 miles are the most important for future bore and ring life. That said I don't know about a factory build as I think they run them before they sell to the public and do not build to the tight tolerance that an independent engine builder should do.

@seemssafe2995

Жыл бұрын

soft break in if you dont want your rings to seat

@6Twisted

Жыл бұрын

@@seemssafe2995 Bruh, you're replying to a 6 year old comment.

@seemssafe2995

Жыл бұрын

@@6Twisted ill do it again

Thank you! Your videos are awesome! What is the life expectancy for piston rings? How many miles/ how many years? Thanks again! Timo

@DonutHole123

8 жыл бұрын

Some last longer than others but with regular oil changes/general maintenance you should go at least 200k miles without oil consumption. My dads Mitsubishi Outlander has 305k and I don't think it consumes any oil, maybe a very little amount.

Thank you for this video. I've been looking for a good piston ring video, and this explains them very well! Keep it up.

Just now learning about something I have used for 55 years. So what happens to the gas that passes into the crankcase and is pressure inside the crankcase a problem. Thanks for your presentation. Extremely well done.

That kinda ended abruptly. I was hoping for more details.

@GreatGrandmasterWang

5 жыл бұрын

AeroElectro that’s what she said

@benjamingrimes3304

5 жыл бұрын

@@GreatGrandmasterWang LOL!! 🤣🤣

@prithvirajdj

4 жыл бұрын

@@GreatGrandmasterWang 🤣🤣🤣😂

sir, can u make a video on Hard break-in. I really like how you explain things with engineering point of view, appreciate it so much...thanks

Might do a vid on the different configurations of rings, cyl walls, Nikasil, cast iron and the advantages and disadvantages. Great video as it is.

U saved my day .... has a GTI with high oil consumption. ...and wasn't getting what's the real issue for vehicle . Almost 2 weeks of restless days. The piston rings are worn out and oil gets to combustion area and burns off... In high speed oil just becomes so thick and in 20km around 2 liter if oil gets burned .... But in low RPM .... there's no oil burning .... actually your video made me get the actual problem for the vehicle .... Anyway it's expensive to rip apart the engine and reassemble. ....going to do it anyway ...... Thanks a ton ...mate

How about thicker & lighter oils on new & old car engines. EO provides lubrication and sealant between piston ring and cylinder wall. Since older engines have bigger wear and tear, does using thinner EO affect compression and combustion. vise versa. Thanks

@icekk007

8 жыл бұрын

+Tango965 Yes, engine oil provides sealing between the piston ring and the cylinder wall. If the wear on the piston ring is excessive, no oil will help sealing it. If the wear is small, a thicker oil may help. The property of engine oil that matters is High Temperature High Shear (HTHS). You can find HTHS in an oil's product datasheet. An oil with high HTHS will form a better seal between the piston ring and the cylinder wall.

@rollipollirock

4 жыл бұрын

icekk007 if you have VVT heavier oil will not be good for your solenoids

Hi, Can you make a video on how to remove these blow by gases from your engines' sump I am talking about the ventilation of crank case. Thanks

Great video, thanks for the explanation. Those look like the newer type of rings that you can install without any tools. They look so flexible which helps reduce drag on the cylinder wall and increase mpg (change oil regularly to prevent sticking). It would be nice to have technology to produce an artificial layer of diamond surface in the bores and a coating on the rings to inhibit wear.

Excellent, concise presentation, thank you! Loved the whiteboard in particular.

Wouldn't the power stroke in the cylinders be more susceptible to blowby squeezing past the rings rather than during the exhaust stroke, when the spent combustion gases already has exited the cylinders? Blowby happens when combustion pressures seep past the rings and make its way through the crankcase and out the vents, taking oil vapors with it into the intake, correct?

@roadrunnerblink

8 жыл бұрын

+OCTurboJoe I know what you're getting at but the blowby doesn't "squeeze past the cylinders" in one go. Look again at the diagrams in the video. It happens in two stages: 1) The exhaust stroke forces the rings DOWN letting gases into the top part of the gap. 2) The compression stroke now forces the rings UP which releases those gases out of the bottom of the gap. It is a two-stage process. It would take an incredible amount of power to blast those gases past the rings in one go. Maybe if the rings were very worn though.... Hope that helps.

@octurbojoe

8 жыл бұрын

+Boysya Exactly. It's more pronounced with force induction. A newly built engine with a fresh set of rings can still have a good amount of blowby. Pressure will always find the past to least resistance, especially through rings on the power stroke. The exhaust stroke is more like negative pressure where gases exit the chamber vs positive pressure pushing past the rings, into the crankcase, and out the vents. This video probably explains blowby at idle whereas I am explaining excessive blowby under load.

@jacobfraser7967

8 жыл бұрын

+roadrunnerblink he didnt describe it well, in fact most blowby is caused by bad ring to cyl seal, not by a tiny amount of space behind the ring

Could you please make a video about breaking a car in? Mythbusting or the usual. The topic is so controverse, but also so important. Cheers!

I would just like to have you teach me everything engineering. I really learn a lot from you.

Wow, I was expecting it to be longer, but it was actually 3:50! So good job explaining that time went super fast.

no fast and furious remarks? interresting

I believe piston rings in an engine form whats called a "labyrinth seal"

@icekk007

8 жыл бұрын

+Bill T Labyrinth seal is not used in piston ring. I think it is generally made of elastomer (rubber) material, so it can withstand the heat and pressure experienced in a piston. They are generally used in shaft seal in rotating machines.

@ShaunHensley

6 жыл бұрын

Bill T Labbys are on rotating assemblies as was mentioned, but they definitely don’t have to be soft like rubber.

@mummyjohn

5 жыл бұрын

Yes it is a variation of the labyrinth passageway, you don't line up the ring gaps all in a row for this reason

I would be really thankful to you sir if you explain about the practical working of manual transmission of bikes and cars

this vid answered a few questions I've been thinking of. subscribed!

what metal are these rings made of? I always thought they're rubber.

@VinaySharma-zt3gk

8 жыл бұрын

Same

@stradplayer90

8 жыл бұрын

Not since the early 1900s has that been true. They are made out of a very hard, springy, and brittle steel.

@VinaySharma-zt3gk

8 жыл бұрын

+Jean-Paul Veillon Oh!

@danalex6129

8 жыл бұрын

cast iron

@midniteoyl8913

8 жыл бұрын

+Mohamed Li Usually cast iron for the Top Ring, cast iron or steel for the Second Ring, and steel or stainless steal for the Oil Control rings

explain PCV valves please

@Hank_Dog

8 жыл бұрын

+TheWolvesCurse essentially, you have a valve on your crankcase that lets air/fuel out of your crankcase back into the intake manifold.

@peterjensen6844

7 жыл бұрын

When the vacuum pressure of the intake manifold/throttle body is in the correct range, the PCV valve opens and uses that vacuum to pull blowby gasses out of the crank case and pull it in to the intake and reburn it. Its an emission control system. If that valve is stuck open, you could suck up engine oil and cause all kinds of issues with the intake or throttle body.

You are like my personal teacher. Keep up the good work!

Extremely helpful, thank you man.. so my motors junk unless I replace those rings... good to know.

you should go wayyy deeper into this subject. You could make a 30 min video if you went deep.

@Viralityoflife

8 жыл бұрын

+fightfanian how deep? Really deep?

@fightfanian

8 жыл бұрын

+Mike Halpert balls deep

@Viralityoflife

8 жыл бұрын

+fightfanian like hodgetwins sugar walls deep?

@Snowcrest289

8 жыл бұрын

+fightfanian A Basic overview gets the job done in :05 minutes. Well Done!

@Boz1211111

8 жыл бұрын

+fightfanian I was actually expecting that...

In other words...if you own an STi, buy an Air Oil Separator.

Great Video! Nice, simplified explanation! Keep up these great videos!

Great quick explanation. Easy to see why you should do regular oil changes.

Why are cylinder rings so much more reliable and durable than the Apex seals in a wankel engine?

@jamtea573

8 жыл бұрын

simply that the heat is more intense and builds up on one side of the block more than the other, so there are more cooling issues to overcome. Plus the oil, if not regularly topped up with the correct type will mean that there is more wear on the seals. Not to mention that the wall exhausts in the standard 13b design mean that they are regularly passing over the port which can cause some wear when it touches the other side (overcome in the renesis MSP design). The oil used however, even in this design doesn't burn 100% cleanly, so the residues that build up will cause seal wear and degradation over time. 2T Premixed fuel and SOHN oil reservoirs do help in reducing these types of wear, which would be nice to see this channel cover.

@einseinseinseins

8 жыл бұрын

***** ***** thanks! That makes sense;)

Blowby = Volkswagen TSI engines

@yourfather5324

3 жыл бұрын

Yep

Nice explanation and very good graphics/picture quality, Thanks a ton man 👍

Fantastic explanation. Thanks for the great diagrams and use of real components for demonstration.

We thank you for all the efforts you put to explain to us every time

I just learn this from your channel. Great one!

thank you for sharing technical knowledge...

I was super hoping you would have a video up for the new Formula 1 Engines (Mainly the Hybrid System) for the season opener this week. Great explanation of piston rings though!

Very informative video thank you.

thank you very much. your video is very helpful in understanding the concept of blow by. keep makinh videos like this. again thank you

Always great demonstration and explanation. Great job!!!

Thank you Jason. Good explanation as always.

very helpful video for people like me who only have hands on knowledge of suspension/brakes/wheels etc. but haven't done any sort of internal engine work.

Thanks, this channel really helped me a lot to learn for my Job in Shell.

WOW you are awesome Engineering explained. I discussed this topic with someone from the comment section like 2 days ago. And some said this topic was to small. yet you made the video I wanted. thank you so much. Have a nice day :)

Great explanation. Thanks for the great vid. Subscribed!

Great!! Simple, detailed and very quick. Keep it up!!!

Excellent video as always.

Excellent video! You could go a bit further and describe ring flutter and more issues caused when crankcase pressure is allowed to be present creating instability creating more wear and blow-by. This is common when tuner shops don't understand the functions of the PCV system and proper crankcase evacuation. You always want to pull suction on the crankcase to maintain proper stability and ring seal. When this is defeated and breathers added to "vent" your allowing pressure to be present. It is not hard to install a crankcase evacuation system that pulls suction at all times emulating a belt driven vacuum pump for the street. Good video!!

Great explained it right... Reverand Auto🧐... I had tire down a v6 Ford ranger for head gaskets piston was burned on corner not round at all seen 2/3 of rings .. Motor smoking oil in mass a.f. tube to throttle it had watered oil in also...

dude! 30 seconds into this video and I knew this was going to be informative, good job

Really good demonstrations in all your videos. Thanks

Working on a single cylinder engine from a mid '30s italian motorbike I was taught that, when it is time to reassemble it, it is better to place the "gaps" in the rings 180° one from another. That way you increase the lenght of the path for the blowby gases therefore reducing it. I also think that the rings can somehow rotate when the engine operates so that may be partially true.

Excellent vid, thanks!

Show your videos to my students as they are well present and easy to understand.

Great video! Can you do a follow up vid explaining why blow by might be a good thing (turbocharging). I would also like to know how is the Total Seal rings different. Thanks!

@HutchCoRacing

8 жыл бұрын

+Chris Nalley blow by is not good. at all. causes oil vapor to be sent through you pcv lines and back into you engine, causing detonation. what "could" be good about is in turbo applications?

@ericstites9470

6 жыл бұрын

Total Seal makes conventional rings, and then they make several differing sets of "gapless" rings. Those gapless rings are essentially two rings in one piston groove. The upper ring has a "step" on it that the lower ring sits on. The gaps of each ring are offset by 90° or so just like conventional rings, and since they're both in the same groove it effectively closes off both gaps - hence, a gapless piston ring. Also, that tiny bit of combustion pressure that gets behind the upper ring helps push the combo tighter against the cylinder wall thanks to that internal step that the lower ring sits on. Gapless rings produce a little bit more friction than conventional rings, which could all but negate any power gains in smaller engines. But even so, the far better seal against blowby would make for a cleaner engine, meaning you could possibly even skip an oil change here and there if you wanted. Plus, low-tension oil control rings and low-friction coatings on cylinder walls would negate any frictional losses due to running gapless rings, freeing up more power.

Thank you so much mate.... this clears my doubt about blow by

Thanks for the video I am concerned about the theory of 4 stroke engine motorcycle piston rings correct positions

Breaking in a new engine is something everyone and their brother has an opinion about. One might say to take it easy on a new engine for the first 1k miles. Another might tell you to drive it like you stole it in order to "set" the piston rings to the cylinder walls. This video got me thinking about those opinions. You should make a video on the proper way to break in an engine (if their is one) and what you should or should not do. Love your videos by the way!

Engine oil also helps to create a seal within the rings. The scraper also helps with portioning the amount of oil that is allowed to stay in the cylinder to keep things sealed and lubricated. Interestingly enough, the pistons on aircraft engines do not have those weep holes because you're dealing with bore sizes over 5".

Explained good ,could you do a video explaining crank case pressure?

Hey Jason, thanks for the awesome explanation as always! I was wondering why does the piston ring grooves allow a vertical play for the piston rings. I think that if there weren't any vertical play, the exhaust gas would not get in to the grooves and make its way down to the crankcase. One explanation that comes to my mind is may be it allows the first piston ring to have less stress on it by allowing the play. Can you please elaborate on this? Thanks!

Wow great explanation. Easy to understand.

+Engineering Explained you should do a video on the pros and cons of low profile tires versus standard tires.

Hi Jason. Have you heard of the motoman break-in method? It would be awesome to do a mythbusted video on that. I personally am a believer as I've seen the results first hand. Many people do not realize how this works. Thanks for the awesome videos!

wheo, 4k vid. nice job! really apriciated! keep it up!

Excellent Video as always..my question is, is there anyway to set you piston rings after hone your cylinders walls. I did a leak-down test on a few of my cylinders and found that a few of them was low 20 percent leakage. the leak down showed that the air was coming from the crankcase. so i took them out, hone out all the cylinder that were low. the pistons and rings are now back in which brings me back to my question above. thanks for your feedback

thanks, now i have more understanding of why my 06 ducati s2r is blowing black smoke, my mechanic said i will have to tear down the whole engine which is too expensive for me. the cost is not justifiable, i might as well get a new bike without the hassle. i will do more diagnostic and see if i can reduce the black smoke without tearing the engine down.

could you do a video on engine breakins/running in. and what you believe is best. hard or soft breakin ;)

Absolutely love these videos

great video, very nicely explained! subscribed

Great video! Could you possibly explain the pros and cons of gapless rings? Are they more for racing applications than for a daily driver?

@patw52pb1

8 жыл бұрын

+Dylan Krone Gapless rings when sized and installed properly provide a better or more total seal than traditional gapped rings, but... they usually do not last as long before replacement is desired. Gapless rings can make more power by sealing better and can help prevent oil contamination detonation at high RPM. Some gapless rings are also low drag meaning they produce even more power via less parasitic friction. Daily driver is subjective, what I will accept and consider for a daily driver and all that is required may totally unacceptable for you or someone else.

Your a good teacher I thought I was actually doing it by my self

I really like that we have such an educated car nerd. Great explanation of how it works. 30 year mechanic myself you do pretty well. Only seen a couple of your videos that were questionable. My question is can you actually wrench?

Great explanation as usual. Thanks.

good video and very good presentation. Even I who dont know anything can understand.

Thank you so much! That was really educational! :D :D

Another excellent video!

I have a question regarding the gaps on the piston rings (2:30) , specifically for a small engine. When installing the piston, does it matter if the gaps within the rings get set alligned or do the gaps need to be set opposite to each other?

Very beautiful & rational explanation, thak you!❤

love this guys videos!

Do a video on blow of valves please, advantages and disadvantages and what you general think of them from an engineering state of mind ?

@patw52pb1

8 жыл бұрын

+steve hadjivostas Use them, size them properly and save the compressor turbine and bearings.