I live in palmer alaska and always wonder what our crazy neighbors are up too. I have always looked down on Russian cars but when the government pretty much builds your cars you shouldn't expect greatness. I hope one day our nations will be back on good terms our world is so much better united then fighting with one another.🇺🇸🙏

@kranksgaming

Жыл бұрын

It’s not the people that make the terms bad it’s the government manipulation that does, remember this.

@therealswarvey

Жыл бұрын

Ladas are steadily becoming more of a collectors item worldwide. They should release a new model Lada called the "Olive Branch"

@butcherbaker4258

Жыл бұрын

@@kranksgaming thats exactly what i said🤷‍♂️ remember that

@kranksgaming

Жыл бұрын

@@butcherbaker4258 how crazy is what I wrote imagine if every human in the world read what I wrote and understood, technically would change peoples way of thinking if they weren’t already stuck in a shit way. Peace and love to everyone

@CarLoverPhotography

Жыл бұрын

The fact that it started back up and drove into the shop with holes in the pistons in pretty impressive.

i did this to my Vespa piston...i had bad pre ignition timing issues and the plug burned a hole through the crown so i used JB Weld on it and sure enough it ran, but within minutes the hole burned right through again

@XNeo27564

Жыл бұрын

Lol I once drove 30 km from home with a buddy as passenger. I got a loud pop and I noticed throttle response was lower and I needed to keep it alive. It brought us home, died in front of the door. And I found out later a piece of piston 'has left the room' size 5x5 mm on the top outside of a small 70cc 2 stroke piston... lmfao. It brought us home 👍

@dangerousfreedom4965

Жыл бұрын

Weld it lol

@Dcale

Жыл бұрын

Tig

@rgracing4109

Жыл бұрын

I guess you guys don't have parts readily available over there like we do in Europe

This channel is more like a research lab. Amazing stuff!

Drilling the hole up to a standard tap size and putting a bolt in it would certainly be interesting. Should last much longer than filling the hole with adhesives. Still going to need some form of adhesive as thread-locker to prevent the bolt from backing out and to seal the threads though. The first cylinder to fail was almost certainly the baking soda. I was expecting the other two to fail within seconds at load, looks like they lasted a whole lot longer.

@giggiddy

Жыл бұрын

What a cool concept. If you screwed the bolt in. Brazed the bolt in from the backside, and ground the head of the bolt level with the piston... Wonder how long it would last? Cheers

@maxstress8427

Жыл бұрын

@@giggiddy That is a good idea... what if you were to use all thread rod, no bolt head to deal with and less grinding to make it flush.

@giggiddy

Жыл бұрын

@@maxstress8427 Love it! Would love to see how long it would last. Roadkill used to bandaid stuff together like that then take a road trip. Repairs like that interest me. Its incredible how long some of those "bush fix" repairs last. Cheers!!

@scottvincent7666

Жыл бұрын

Drill and tap for a Allen key pipe plug. After installing pipe plug the excess can be ground smooth.

@MegaSockenschuss

Жыл бұрын

@@giggiddy oh man, Roadkill... great times! I really miss these duct tape & zip tie adventures.

Back in the eighties, I burned a hole in the crown of my Vespa's piston. So on the roadside I removed the cylinder and piston then I used Araldite to fix a 2 pence piece to the underside of the crown, waited for it to cure and then filled and smoothed the hole atop the crown with more Araldite, put it all back together and I got several hundred miles out of the blessed thing until the glue gave out on the 2p and the 2p coin dropped into the crank and smashed everything up inside.

@Buck3366

Жыл бұрын

I got to the end and burst out laughing. Just imagined the 2p zipping around after what was some genuinely proper roadside ingenuity.

@operator8014

Жыл бұрын

Worth every pence.

@martinda7446

Жыл бұрын

Ha ha ha

When I was about 10 I had used JB weld to glue a nickel to the cement floor of our basement. My dad tried to pick it up and failed (obviously 😆) so he got a hammer and chisel to remove it, but the JB weld didn't let go, the nickel took up a chunk of cement when it was pried off 😆 and from then on I knew it was seriously tough stuff.

@dannydaw59

Жыл бұрын

I was wondering if gluing a quarter to the sidewalk infront of the house (when I was a kid) would work. I guess jb weld would do it.

@jwalster9412

Жыл бұрын

Do something more serious. JB weld a 100 to the sidewalk infront of a bus stop or something.

@timjohnun4297

Жыл бұрын

Project farm cut a hole in a cylinder head and JB welded it up, and it actually worked. Not sure how long for, mind you. I repaired an outboard cylinder head with it, about 2 years ago now, it's still going today

I just love the English translation man, it’s awesome. He seems like a professional translator. Love and respect .

@SwapBlogRU

Жыл бұрын

Not exactly a professional, I've just been doing it long enough to become somewhat competent.

@MegaSockenschuss

Жыл бұрын

@@SwapBlogRU I'd say that's the definition of a professional. :)

@donaldgminski8621

Жыл бұрын

I honestly think it makes the videos a little fun.

@SwapBlogRU

Жыл бұрын

@@irgant ну такой он, да, простоватый мужик. В жизни много матерится)

@soldjahboy

Жыл бұрын

@@SwapBlogRU I'm sorry, did you say... super professional, and awesome? That's what I thought you said. :)

6:10 “ Engine pissed out some oil, but no biggie “ ❤❤❤ 👌🏼

I once welded a cast iron piston that had a valve stem go straight through the top of piston .and weighed /balanced it after welding . Don't forget to pre-heat the piston before welding

@PhilJLF

Жыл бұрын

Lol it’s setting off car alarms … the cars parked are like “stay away you sick bastard!” Hahahah

@jwalster9412

Жыл бұрын

I wonder how much that hurt the engine efficiency. Would you say you replicated the original well, or did you rush it just to have the car work?

@therealswarvey

Жыл бұрын

What happened to the valve originally? Sounds like some very cool carnage

@Varinki

Жыл бұрын

@@therealswarvey It either broke or the valve retainer came off and dropped the valve.

@therealswarvey

Жыл бұрын

@@Varinki yeah, but it had to go somewhere else in the engine

Hi Instead of using gaskets when building an engine can you guys weld the motor shut... No gaskets just welding Hope to see this crazy experiment soon Love you guys 👍🏽👍🏽

@jjohnston94

Жыл бұрын

Probably wouldn't work. At the block/head joint, there are a lot of oil and water passages you'd never be able to get to, to seal.

@yuhmother

Жыл бұрын

@@jjohnston94 🤔right right....true....🤔

@jasonharrison25

Жыл бұрын

solder it. might be able to get the solder to wick inside the gap and seal it all up

@martinda7446

Жыл бұрын

Er, no ha, ha, ha. it could only be a disaster... So good idea!

Love watching you blow the crap out of engines to test different theories

The guys at Garage 54 are tops at proof of concept!

I repaired my 2 stroke motorized bicycle engine's piston with epoxy glue but damage was on skirt of piston and it worked very well

Never say "it won't work" until you've seen G54 prove it one way or the other. The ultimate in automotive standards lol

Just "CLASSIC" to see the door swing open on the right hand turn into the shop !!!

I know at least the super glue will release with heat for sure. I use it to hold small 2 stroke cylinder jugs onto a mandrel to cut the bases a few thousandths to raise compression on chainsaws. Just a small amount of heat that jug slips right off. JB Weld I've had mixed results with heat on different things. EDIT: I really did think they'd come apart a few seconds after startup. Lasted way longer than I thought. Lol

@kitecattestecke2303

Жыл бұрын

There is special high temp JB weld and if you work very clean, very clean surface it should hold up some :-) maybe pressure on a piston hole is also too high to work

@contraband1543

Жыл бұрын

@@kitecattestecke2303 They make a 2 part putty called Steel Weld and I guarantee it would hold up to this for as long as the engine lasted. It gets hot when mix it and after it cures it is as strong as steel for certain. You can hold a blowtorch on it for as long as you want and it wont melt. You can tap it, even make bolts out of it. Yeah I said *create bolts out of putty* lol

@therealswarvey

Жыл бұрын

Lookup a channel called Project Farm if you wanna see JB weld REALLY put to the test. Including a small engine cylinder head made entirely JB Weld

first class stuff as always there is never a dull minute with u guys with fun in mind . so much better than the negativity that corrupts the rest of the world, blessings to u all .

Such crazy brilliance! You guys are incredible and I love watching all the insane things you guys come up with. Thank you for thinking outside the box. Can't wait to see what's next

"I Thought I Heard Somebody Say They Would Break Immediately." *That Was Me Dude!*

Bring holed pistons to tdc and weld up in situ, quick easy repair and get it running back on 4.

👌😂👍that poor Lada has been through hell and back! You guy’s been trying to kill it for a long time now with all your crazy experiments! And still going strong!😂👍

Interesting way to simulate a hole in a piston. Great idea.

I like how the test vehicle at the beginning has two bumpers and two different license plates 😯

I enjoy your videos very much! You really have a unique channel, thank you for sharing!

Love this man

You guys should make a wrist pin or a connecting rod out of ferrocerium fire starting rods.

@madmod

Жыл бұрын

Good heavens

Since you welded a piston,i would really like to see you adding welded material on the pistons as much as possible to get maximum compression and see how much power it will gain

@gabrielv.4358

Жыл бұрын

Agreed

@MrRaab-hu9rs

Жыл бұрын

+1. Please do. It's not that the engine can get any worse.

@HR15DE

Жыл бұрын

the amount of air it can intake will also decrease

@jwalster9412

Жыл бұрын

It would probably do easier and way faster to just shave to top of the block.

Thanks for doing this product testing. I was thinking of using JB in a different application on a small engine - ie. for threads stripped threads, but it seems it might have a short hold time in that application as well.

Great experiment guys 👍

Hey there fellas 😎 I love ❤ the intro always makes me smile as usual hoping you guys are well and safe brothers 🇬🇧🍻🙏

@SwapBlogRU

Жыл бұрын

Have a great evening!

@co2addicted788

Жыл бұрын

@@SwapBlogRU thank you 😊 so much you to buddy 🙏

next up, i would like to see a modified camshaft to increase power, with nothing but a welding gun

@electronJarvs

Жыл бұрын

This is a great idea

You do some crazy stuff

Im a fan of aluminum dust mixed with jb weld. It works great

@madmod

Жыл бұрын

@Aussie Doomer powder/dust/shavings all work perfect haha

A good classic experiment. At this point I'm starting to think that Cyril left.

Try using JBWeld Extreme to glue a coin to patch over the hole. Coins are tough. Obviously it depends on valve clearance. You might even get a performance boost from the increased compression LOL.

"What we saw upset us and we decided to go home" man I feel that bahahhahah

At 2:45 I saw your stunt doubles go through the back door.

So some context, the piston head experiences the peak highest pressure of 2100psi on every single stroke, it also experinces the most amount of heat being the closest to the explosion in order to do it's job. So while it failed to repair a piston head, the block itself would be fine with JB weld, having experienced a fraction of the heat and concussive peak pressure that the piston takes. As the piston travels down and expanse the pressure rapidly drops meaning the walls of the cylinder would be able to handle the jb just fine.

Lol it’s setting off car alarms … the cars parked are like “stay away you sick bastard!” Hahahah

Wow, Garage 54 is following in GM's footsteps in successfully duplicating the 1.5L Ecotec engine.

Amazing!!!!!!!!!!!!

From 11:00 your lada started sounding like a lawn mower 🤣

JB Weld probably survived the longest of all three glues.

Do a homemade spark plug episode that would be very entertaining

You have good welder ;) that's why TIG welding resisted! Could be interesting to do the same test with different technologies of welding (MMA, TIG, etc...)

You can mix the jb weld with steel shavings and it’ll hold.

I was half expecting the JB weld to survive if I'm honest, based off my own experience. Although I won't say I'm TOO surprised it failed

I like how the old dude just jumps in the video LOL!!

Predictions: The cyanoacrylate "super glue" will prove too brittle, shattering in service. The epoxy will get gummy with heat and peel out. I have used JB Weld and it has proven very fit for the purposes I put it to, but those purposes have not included using it in a combustion chamber. I think, on zero evidence, that it'll work for a little while before it fails. I expect the welded piston will still be working well after the other three have failed.

You guys are awesome lol

Tig weld the other 3 and test to see if how close to factory compression you could get by fixing it that way

Gotta love those ideum. Yeahm.

I wonder what would happen if you jb welded a piece of aluminum to cover hole might deflect some heat and hold up longer?

Yes

One adhesive you can try is 2 part putty. It has metal filings in it & it withstands high temperatures.

@soldjahboy

Жыл бұрын

That's what they used. That's what JB weld is. Metallic two part epoxy putty... but it's not strong enough to hold the force of an explosion in a compression chamber.

@christophermarshall5765

Жыл бұрын

@@soldjahboy not the putty I’m talking about. JB weld is liquid form. The stuff I am talking about isn’t. The one I am talking about is called “speed stick “ instant putty, it is a substance similar to radiator and fuel tank repair that you knead together, then press it into place. You can cut threads in the stuff once it’s set.

@soldjahboy

Жыл бұрын

@@christophermarshall5765 The JB Weld I've used is exactly what you're describing. I've never seen liquid JB weld before. The stuff I buy is in two solid sticks and you break a bit off each one and kneed it together. I think it's called JB weld steelstick.

@christophermarshall5765

Жыл бұрын

@@soldjahboy the JB weld they used in this video is in 2 part epoxy liquid form. The stuff I described is what I used to fix radiators & steel fuel tanks. It is in a single strip, that you break off, & knead it until it turns grey. The steel stick I also described is not made by JB weld. Their products are 2 part epoxy adhesives.

This was an interesting experiment! Try the nut and bolt idea, with a countersunk head. What could go wrong?!

Poor old Lada but I imagine one in good condition is pretty reliable. Russian machines tend to be simple but very robust. So a piston can be repaired by welding.

Try braze weld ing them with brazing rods should work nicely

@patrickbrady447

Жыл бұрын

You can not braze aluminum

Try quiksteel and keep it under pressure while curing

A challenge for you? Take your knackered engine, fit it with four square cylinder sleeves, and make four square pistons to fit the cylinders, then drive the thing? Are you up to the challenge?!

@SwapBlogRU

Жыл бұрын

Would it even run?

@whitesapphire5865

Жыл бұрын

@@SwapBlogRU That depends on how good a seal can be developed between piston and cylinder wall, but then that's why it's a challenge.

@deadaccount6135

Жыл бұрын

@@SwapBlogRU you guys are the only ones who could make it work. My thinking is, cnc machined for perfect seal joined surfaces, two piece L shaped ' rings ', slide them in and carefully weld them together in place on the piston. Since there's no compression sleeve for these rings you might could liquid nitrogen freeze them to shrink them enough to install them. 🤔

I want you guys around in the coming zombie apocalypse, because you already know how to make the best out of the worst things lol

It will permanently fix a cracked oil pan. It worked for me, been years, no leak.

I still say yall need to do a super Lada race car build with all the test that were successful like the pistons rings for one

I typically fix burn holes in a piston with a new or used piston! It’s just too much work experimenting with other types of repairs. I guess if you have a rare and hard to find piston , welding would be the only other option!

@anonymousinc6330

Жыл бұрын

Maybe you're not aware of this, but these guys try all kinds of crazy stuff just for the hell of it. Most of it is never intended to last, more or less just to see what will happen.

Maybe try ceramic epoxy. The same that is used on spark plug insulators and other high voltage or high heat applications. Or make pistons out of the epoxy!

@robertisaar

Жыл бұрын

Ceramic coatings have been done forever with good results, but a fully ceramic slug? I dont know that I've ever seen it. Skirt design might be interesting.

how long should you wait for the welded piston to properly cure ?

Always curious.

Hahahha i lost when he said: ayayayayayayiaiaiaiaiaii

👍 Nice

This means you need to tig weld the other 3 and try again.

They should have stuck an inspection camera down the spark plug holes each time a cylinder went to see which broke first

@66chevystepside

Жыл бұрын

I hoped they would to see the order of failure

perhaps can use a Ceramic piston or cast concrete piston as alternative.

Blessed be the holey pistons... :P

Make high compression pistons by putting a button head Allen screw in the top of each piston will it work?

What happens when you put the spark plug in the piston?

I do a bit of work on geo trackers and they're known for developing cracks in their aluminum blocks between the cylinder sleeves. A girl thought she had a blown head gasket but when I pulled the head I found cracks between 1&2 and 3&4. My initial thought was pull it and replaced it but i've had so much luck with jb weld and we had nothing to lose so I patched it with jb weld and put it back together. That was a year ago and she's still running it.

@jkeelsnc

Жыл бұрын

I love JB weld. It is amazing how tough that stuff is and how durable and heat resistant it is.

I would love a LadaCamino.

Make some hi compression pistons by welding on top of them ore make some would be awesome

What about tapping the hole and using thread locker

👍👍👍👍

at first, a bad valve seal causes idle problem that goes away when revving

👍👍

Pull all 4 of the rods and pistons out and see how far you can drive on just the starter motor. electric car ! Try it on one battery, then try it with a bunch of batteries.

another suggestion? how to fix? buy a new piston, they are cheap to buy, compared to all the work welding up and machine it to fit again But ok, it was a nice experiment. Why? JB weld is good ok, but if used, take care, and maybe only for non stressed erea's or parts. It has been used for altering inletports of modified cylinderheads, but even this is not as good as welding up the ports wich i did.

Now you have to try nut & bolt 😂

That’s pretty damn cool

That car looks like something out of a mad Max movie 🤣

@heyitMeMcFlyunfortunately

Жыл бұрын

thats communist designs

Lada powered siege engine … Like a trebuchet or a catapult

Jb weld isn't good with heat. We tried to quick fix our exhaust with it and the smoke and smell was aweful 😅 it held though just took weeks to stop burning off

@ouch1011

Жыл бұрын

It may sound counterintuitive, but pistons actually don’t get as hot as the exhaust. They see very brief peaks of high temperatures, but the pistons probably have a metal temp of less than 250deg F since they are cooled by the oil and cylinder walls and intake air/fuel mixture to some extent. The exhaust only gets cooled by the air passing over it, so it gets much hotter.

Great test as usual!

Poxipol, vamos Argentina carajoooooo!!! 🇦🇷

I love me TIG!

Next time test exhaust sealant, may resist the temperature

I once knew of a guy riding his 50cc scooter to the BrassMonkey motorbike rally and he developed a hole in his piston, a local farmer welded a coin to the piston and that enabled him to attend the rally. Howsabout fitting hydraulic motors to each wheel and adapt a hydraulic pump to the engine to run the motors?. Or adapt an electric motor to each wheel and adapt a way to power them from a battery with the engine charging the battery.....

15:20 yes please

Try with bio gas tank 💐

How many spark plugs could you add to a motor ????

Dammit

I was thinking nut and bolt lol

Next time try curing the pistons in a furness and inspecting them, it should work better.