made with 5mm EVA craft foam. by request from High Rocker 2240 Fryndej Pattern photo: ZOLUSPROPS/p... Created with Movavi Video Editor www.movavi.com/videoeditor/?c...
Жүктеу.....
Пікірлер: 13
@afaye22684 жыл бұрын
Me *watching this at 10:30 at night without half these materials or any idea*: yes finally a good mask! On an unrelated note I’m going to try this with thicker paper and hope it works 😂
@irishtheyoutuber4 жыл бұрын
one word. *whoa*
@sock3084 Жыл бұрын
How do you figure out where the cut lines are? Especially that funky that goes around the eye. I know the darts are where the bends are for the mask but how do you find out how big to make them?
@ballisticfoamarmory4186 жыл бұрын
start a patron so it helps your channel
@yamisauruslex6 жыл бұрын
Looks so good!!
@ZolusProps
6 жыл бұрын
Yamisaurus Lex thank you!
@randomsniper10926 жыл бұрын
Nice, also would the template for your spawn helmet work for your red hood mask because in your video you did say that you modified it and I wanted to know if it would still work :)
@ZolusProps
6 жыл бұрын
Random Sniper 109 yes it would. The difference is small. I changed the chin so it would look more flush. Otherwise it is the same.
@esquared11964 жыл бұрын
Can you use mod podge or something instead of silicone?
@ZolusProps
4 жыл бұрын
I have used mod podge instead of Alex plus latex/silicone. But, no sanding I just kept adding it to the gap level and repeat after drying until it was less noticable.
@frankcastle22046 жыл бұрын
Like men :)
@benspencer85576 жыл бұрын
Could you do a Kylo Ren light saber
@ZolusProps
6 жыл бұрын
I am not sure. In theory yes, but it would cost a lot more and take longer than most of my projects. That doesn't mean I won't, but it won't be in the next few months. however I did do a video explaining how I modified a 15$ blade builders saber into something more cosplay worthy: kzread.info/dash/bejne/Z6xpytiYeKnfaKw.html Also I was inspired to do this by this video, that also has a good descriptive painting tutorial: kzread.info/dash/bejne/l312sqazgLCocbQ.html
Пікірлер: 13
Me *watching this at 10:30 at night without half these materials or any idea*: yes finally a good mask! On an unrelated note I’m going to try this with thicker paper and hope it works 😂
one word. *whoa*
How do you figure out where the cut lines are? Especially that funky that goes around the eye. I know the darts are where the bends are for the mask but how do you find out how big to make them?
start a patron so it helps your channel
Looks so good!!
@ZolusProps
6 жыл бұрын
Yamisaurus Lex thank you!
Nice, also would the template for your spawn helmet work for your red hood mask because in your video you did say that you modified it and I wanted to know if it would still work :)
@ZolusProps
6 жыл бұрын
Random Sniper 109 yes it would. The difference is small. I changed the chin so it would look more flush. Otherwise it is the same.
Can you use mod podge or something instead of silicone?
@ZolusProps
4 жыл бұрын
I have used mod podge instead of Alex plus latex/silicone. But, no sanding I just kept adding it to the gap level and repeat after drying until it was less noticable.
Like men :)
Could you do a Kylo Ren light saber
@ZolusProps
6 жыл бұрын
I am not sure. In theory yes, but it would cost a lot more and take longer than most of my projects. That doesn't mean I won't, but it won't be in the next few months. however I did do a video explaining how I modified a 15$ blade builders saber into something more cosplay worthy: kzread.info/dash/bejne/Z6xpytiYeKnfaKw.html Also I was inspired to do this by this video, that also has a good descriptive painting tutorial: kzread.info/dash/bejne/l312sqazgLCocbQ.html