Brawo. Super robota!

Very professional job,,,,

@julaskam

Жыл бұрын

Thank you 😊

Amazing job. Well done.

Nice clean job 👌👌👌

Be careful starting an engine with no coolant if you’ve fitted a new water pump. The seal on water pumps is a special type and needs coolant to lubricate it. If you run it dry when it’s new it will chew it out and the pump will leak straight away or very soon after. I learnt this the hard way….

Pompa paliwa powinna byc ustawiona na znaki po ustawieniu rozrzadu najpierw a potem pompa

@JakraJakra

Жыл бұрын

dokładni tak

@JakraJakra

Жыл бұрын

jak nie ustawił to rozrząd wytrzyma max 10tys

Hi. Thank you for uploading such a helpful video. It was very interesting to see whats involved and I greatly admire your professional work. How many hours would be a fair estimate of what is involved including strip down of the head to allow for it to be skimmed ? Thank You so much.

When you put the fuel pump, did you set the timing on it? If you don't you are liable to strip and snap the cam belt over a period of time. There is a mark on the drive gear on the pump, that must be aligned with the mark on the casing. Goes in when the cam shaft drive strocket is locked in place.

@ssss-df5qz

Жыл бұрын

These pumps aren't timed or phased mate. The cam drives gears through a little gearbox which the HP pump bolts to.

@mvemst

Жыл бұрын

Dat dus want het zal niet de eerste keer zijn waar dat gebeurt. PSA waarschuwt hier ook al voor.

@alansimpson4461

11 ай бұрын

These pumps are timed, they will strip the teeth on the belt eventually

@serwis_skakanek5822

9 ай бұрын

​@@ssss-df5qzthis pump is timed. It have only one piston. Easy to recognize, if there is that funny gearbox between CR pump and head, you should time it.

👍

Hey man, Do you have any memory how does the non return oil valve on the head goes in ? There’s a red membrane and I don’t know which way it goes as the machine shop removed it and didn’t put it back the way it was …

Cześć, dobra robota! Po jakim przebiegu była ta jednostka? Jaki problem się pojawił, że została zakwalifikowana do remontu?

how did you get the injectors out? mine are seized up

Je hebt hoop ik wel de timing belt in de juiste gaatje vast gezet en de hoge druk brandstofpomp met de diskette case op de juiste puntje afgesteld? want als je dat niet doet kan je een fibrillatie krijgen in je nokkenas en die geeft het door aan je distributie riem waardoor je riem binnen 1000 km de tandjes af kunnen klappen. PSA waarschuwt daar ook voor. Zal niet de eerste keer zijn en vaker gezien namelijk.

Nice, how much do you charge?

Hola amigo , consulta los grados 220 , se aprieta total o por separado los grados , gracias

Hi, Can you support with tightening torques and specs or service manual? I am working on engine overhaul and I cant find seals for lower crankcase in local shops. Thanks in advance.

Hi Julius. Is this video available at normal speed please? I have this job to do on my van and the disassembly is a bit quick for me to follow :)

@julaskam

Жыл бұрын

Unfortunately no it takes about 3 working days to do so I was recording mostly in time lapse from the beginning.

Approximately how many hours did this take?

@Vlad_Pa

3 ай бұрын

Good few days probably

vous avez fait un grave erreur de calage pompe injection 1000 km casse courroie distribution et arbre à cames

Didn't even time the fuel pump