This is insanely well produced. So easy to learn. One of the best tutorials I have ever seen, thank you so much

@UtGoTech

9 ай бұрын

Glad you liked it 👍

Very good explanation. Clarifies the relation between M1 M2 M3 & M4 motor connecting points and programing them in sketch. Please continue making simple but great videos. Great help for beginners.

@UtGoTech

2 жыл бұрын

Thanks👍

Amazing video !! I was looking everywhere but finally found an amazing video

@UtGoTech

Жыл бұрын

Glad you liked it!👍

Awesome video. Very very well narrated and easy to follow tutorial. I tip my hat to you sir!

@UtGoTech

2 жыл бұрын

Thanks

very nice!! thank you so so much!! love the video design!

@UtGoTech

2 жыл бұрын

Welcome👍

Congrats! Great video!!

@UtGoTech

2 жыл бұрын

Thanks and Welcome 👍

Been very usefull. Thank you very much!

@UtGoTech

2 жыл бұрын

Welcome

very beautifully made us understand the code and motor with motor shield and use of jumper if external power supplied to shield i never seen any other tutorial such way as you described the all function it is a great tutorial power that you have i like it not me i feel all learner will understand it...thank you dear so much your efforts for new learner... i again thanks to you and expect more such beautiful tutorial in future ....God bless you for your kind support through this internet....

@UtGoTech

2 жыл бұрын

Welcome 👍

The best explanation of motor shield. Thanks a lot

@UtGoTech

8 ай бұрын

Glad you liked it.😊

Absolutely helpful. Thank you 🙏❤

@UtGoTech

Ай бұрын

Glad it help👍👍

very easy to understand thanks bro!!!

@UtGoTech

2 жыл бұрын

Welcome

Excellent presentations. Even education colleges are not teaching like this . Easily understandable. May I request you to clarify my doubts.

@UtGoTech

3 жыл бұрын

Yes sure

It's so helpful, thank you very much,

@UtGoTech

2 жыл бұрын

Welcome 👍

loved the video and the way of explanation

@UtGoTech

2 жыл бұрын

Thanks 👍

Best explanation, thank you very much ❤❤❤❤❤❤❤❤❤❤❤❤

@UtGoTech

9 ай бұрын

Welcome 👍

Nice video. Well explained!

@UtGoTech

Жыл бұрын

Thanks

Brilliant video helped alot thanks

@UtGoTech

Жыл бұрын

Welcome👍

awesome explanation man!!!!

@UtGoTech

Жыл бұрын

Thanks 👍

very nice explanation sir.

@UtGoTech

Жыл бұрын

Thanks

Great explanation

@UtGoTech

Жыл бұрын

👍

Thanks. Just worked out why I just destroyed twO UNOs. That jumper🤯🤬. i liked warnings and instructions on packets back in the day.

@UtGoTech

2 жыл бұрын

Welcome

Thank you so much 🙏🏻

@UtGoTech

2 жыл бұрын

Welcome 👍

Thank you very much!!!

@UtGoTech

2 жыл бұрын

Welcome

thank u sooo much sir..this video was very very helpfull...just subscribed :)

@UtGoTech

2 жыл бұрын

Thanks 👍

very useful vedio thank you

@UtGoTech

6 ай бұрын

Thanks Bro👍

Thanks a lot! I had a problem with the M3 & M4

@UtGoTech

2 жыл бұрын

What problem. May be your M3, M4 IC is not working. You can try replacing the IC.

@akhandpandeyvlogs

2 жыл бұрын

@@UtGoTech brother in my case:when I connect motors to M3 and M4 , motor not runs, what should I do please help

@UtGoTech

2 жыл бұрын

You should try replacing the IC

@akhandpandeyvlogs

2 жыл бұрын

@@UtGoTech one more thing... If I giving supply to motor shield with 5000mAh should I have to remove the Jumper or not?

@UtGoTech

2 жыл бұрын

If you have different power source for Arduino board then the jumper must be removed. But if you to power the Arduino board through motor shield then you have to plug that jumper.

Nice..good explanation

@UtGoTech

10 ай бұрын

Thank You 👍

This is really helpful

@UtGoTech

Жыл бұрын

Happy to help

@jaynardmanjares4924

Жыл бұрын

@@UtGoTech i would like to ask help for my school project if i may? Im working with school project with the final goal of having automatic grass cutter. All i need is to have my dc motor program to run specific distance then change direction. Im using arduino uno and L293D motor driver shield. The problem is when i connect the dc motors in motor driver shields terminal such as M1, M2 ,M3 ,M4 it doesnt even work. Even when i try the exact experiment in the website of lastminute engineer it still doest work. So i try to put 1 wire of dc motor in M1 terminal then put another in ground and it work it move forward and recieve the command of stopping before moving forward again but the command about doing backward movement doesnt work and now its a dilema. I also try your experiment but i doesnt work i hope u can help me. is there any way to contact you directly and discuss my problem more. thankyou

@UtGoTech

Жыл бұрын

Contact me on Telegram.

It really helped me alot.... I was going to make a project for science exhibition. .but when I go to ardiuno app to upload the code of motor driver ......it shows error ...showing af motor something. .......but after seeing this I downloaded the library of adafruit ........now its working 😮‍💨😀😀 THANKYOU

@UtGoTech

Жыл бұрын

Welcome👍

So nice...thanka mate

@UtGoTech

2 жыл бұрын

Welcome👍

Thank you so much sir

@UtGoTech

2 жыл бұрын

Welcome 👍

Good super sir VV good

@UtGoTech

Жыл бұрын

Thanks

Really thank you for that sir

@UtGoTech

Күн бұрын

Most welcome😊

Thanks for initiating us!

@UtGoTech

8 ай бұрын

Most Welcome 😊👍

@iznasen

8 ай бұрын

@@UtGoTech I just activated the bell, am full nooby but and am looking to start building something using a Nano IoT with 6 axis, so any help or collaboration would be much appreciated!

@UtGoTech

8 ай бұрын

Yes sure

Thanks!

@UtGoTech

Жыл бұрын

Welcome!

Super excellent 💯

@UtGoTech

2 жыл бұрын

👍

Excellent 👌

@UtGoTech

2 жыл бұрын

Thanks 👍

Great!!

@UtGoTech

2 жыл бұрын

Thanks 👍

Really it worked

@UtGoTech

2 жыл бұрын

👍

Urgent please reply!!! I want to connect ESP32 Cam module with this how and which pins to use and what are all the digital pins available after you connected those motors ?

@UtGoTech

9 ай бұрын

How do you want to connect? What type of RC Car do you wanna make ?

Excellent explanation. would be better if you can say what are the voltage ranges that can apply for the shield also. Thank you

@UtGoTech

2 жыл бұрын

Welcome

@UtGoTech

9 ай бұрын

We welcome your suggestion. Thanks 👍

Very informative! The motor you had used were 12v? or more/less than that...? Can we use 4 motor each of (12v) ? and to run those motors what battery specification we need to use ? 12v is ok ?

@dhruvchaturvedi7030

2 жыл бұрын

Yes 12v should be fine. Try not to exceed 12v just for safety even though the boards are usually made to withstand till about 24v. Also yes you can connect up to 4 12v DC motors but use a high MAh battery or Ac to DC power supply so it works. All the best for your projects!

@UtGoTech

2 жыл бұрын

Correct 👍

Thank you boss

@UtGoTech

2 жыл бұрын

Welcome 👍

Thank you for the video! How long wires could be used for motor with this setup? Would something like 2 meters cause problems?

@UtGoTech

3 жыл бұрын

Yes you can use long wires. Try using thick core wire.

thx!

@UtGoTech

2 жыл бұрын

Welcome 👍

Thanks

@UtGoTech

2 жыл бұрын

Welcome

That's why I owe my university degree to the country of India. I genuinely love you all

@UtGoTech

2 жыл бұрын

Thanks and Welcome

After you use all 4 motors, are you still able to plug in other things like IR detectors elsewhere?

@UtGoTech

Жыл бұрын

Yes, if you are controlling only 4 motors then pin 2,9,10,13 and A0 to A5 are free for use.

hey brother i am not able to get the power supply to m3 & m2 terminals in gear motor driver so i have connected it to servos 1 and 2 ports of the motor driver circuit so how shoul i code ? please help me out

@UtGoTech

Жыл бұрын

Which type of motor you are using?

man you are my hero I was doing a project and now I am sure your video will help me so much , just one question btw I connected 4 motors to the driver and 3 Li batteries of total 11.1 volt and made code for them but after using it for a while on of the ICs got so hot and got burned smoking do you know what is the problem that caused it I bought a new IC and it is again getting so hot while moving the motors

@UtGoTech

8 ай бұрын

Choose motors according to the current rating of the motor driver IC. Maybe the motors are drawing too much current which makes the IC hot.

@YossefSeyam

8 ай бұрын

@@UtGoTech I am using the simple yellow gear dc motors like all videos of making RC car are using it idk what is heating it maybe short circuit maybe the module can't hold the 11 volt

@UtGoTech

8 ай бұрын

Use only 2 lithium ion batteries. Total 7.4V

thanks

@UtGoTech

2 жыл бұрын

Welcome👍

Hi, I am making Arduino obstacle avoiding robot, so i have given seperate power to adruino and driving shield. I have given volte 6 to the driving shield, but my car is not moving properly, it's move slowly, so i have doubt that how much voltage supply we can give to shield???

@UtGoTech

Жыл бұрын

First if you are giving separate power supply then make sure the jumper is not connected and as far as voltage is concerned 6 volt will work but make sure the 6 volt power supply must provide enough current to drive those motors.

can you take the inputs of buttons while using this shield?

@UtGoTech

Жыл бұрын

Yes, there are some free I/O pins you can use.

Sir, I want to connect 4 DC motors each of 12v with 10rpm .what supply do I connect to motor driver shield help me ...

@UtGoTech

3 жыл бұрын

Your can use multiple batteries in series. But make sure motors should not draw current more than 1.2A peak per channel.

Please answer🙏🏻 Can? I connect mobile charger adapter (12v 5a) to motor driver SHILD for power . And I connect 2 tt gear motors. Is it work? I make obstacles avoiding Arduino Robot in 2 wheels.

@UtGoTech

Жыл бұрын

Yes. 12V 5A will work

Hello, I hope this message finds you well. I'm currently working on a project involving an Arduino motor shield and four DC motors. I've encountered an issue where only two of the motors are functioning as expected. I would greatly appreciate any guidance or suggestions you may have on how to ensure that all four motors operate correctly. Thank you in advance

@UtGoTech

8 ай бұрын

Try swapping the L293D IC's in the motor driver shield.

Thank you! This was very helpful and ingormative.

@UtGoTech

2 жыл бұрын

Welcome 👍

Is it just coding to operate the motors independent from each other (at separate speeds for separate times at different stages of a process) or is required to add more elements to the circuit or change it?

@UtGoTech

3 жыл бұрын

Just coding

@quesomanz

3 жыл бұрын

@@UtGoTech Sorry could you share the links of the specifications of the components that you used?

Thanks for your effort sir Mmm what does ut stand for

@UtGoTech

2 жыл бұрын

Welcome

Hello first of all great video Im having an issue Im connecting a 28BYJ-48 Stepper motor (I have checked the connections many times) and im powering the shield with a 12V 2A adapter It doesn't rotate nor vibrate only it heats up I was earlier using 2 nema17 motors and those weren't doing anything Pls suggest me what am I doing wrong is it the supply issue or is my shield broken? Ps - the led on shield does glow when powered with external supply i have also unshorted the pwr pins

@UtGoTech

Жыл бұрын

Don't connect anything with motor shaft and try to operate it.

Hi, Why did you set the speed to 200 and not 250 when you could have? And why shouldn’t you use the jumper when you give power to both the Arduino and the shield. Just out of curiosity.

@UtGoTech

2 жыл бұрын

Speed was set to 200 because I want to drive at lower speed. Power rail of Arduino UNO and the motor shield is connected through that jumper. So in order to use different power supply you have remove the jumper otherwise heavy short-circuit current will damage the components.

How can i randomise the intervals of a servo movement? Like lets say i want robot eyes to open and close at random times. And to keep doing that, until power is shut off.

@UtGoTech

3 ай бұрын

You can use the "random" function in the Arduino IDE to generate a random number and use it as an interval.

sir , in my moter driver shield l293d, when i connect moters it is not working. i am useing 12 volt battery, plzz reply.

@UtGoTech

2 жыл бұрын

What type of battery you are using

I want to control 4 motor( 'any type of motors same or different type like dc or stepper or servo')independently in different direction and different rpm.it is possible or not with this sheild .if it not possible with this this sheild then which shield should i buy . THANK YOU

@UtGoTech

3 жыл бұрын

Yes you can if you play smartly with timings and coding.

Hello! Please answer. As you can see on 1:52, on the lower right corner, there are rows of holes in there. I've followed a tutorial of an "Arduino Vacuum Cleaner" with this exact same motor shield, except his motor shield has like pins or something connected to the hole where you can insert something there, while in mine, it only have holes. However in the order that I've received, there are a row of black things with like a metal pin in it. What do i do? I really need to insert something to the holes in the bottom right

@UtGoTech

5 ай бұрын

You have to solder those header pins in those holes so that you can connect the jumper cables directly.

@kasuke2973

5 ай бұрын

@@UtGoTech thankyou, problem has been solved

@UtGoTech

5 ай бұрын

Great 👍

best place to buy Arduino board and Arduino shields

@UtGoTech

9 ай бұрын

Where are you from ?

Hi Sir! Is it possible to connect LCD display on this prototype to show motors are running/stopping if I'm using Arduino Mega 2560 board? And can also connect a manual circuit using stop/start buttons so that I can control the motors manually and automatically if I want? If possible I do I connect the board and write the code?

@UtGoTech

Жыл бұрын

Yes you can.

I made a four wheel drive car, but the motors connected in motor 3 and 4 slot are running slower than the motor 1 and 2, is there any fix for this?

@UtGoTech

2 жыл бұрын

Have you used same motor ? What is setSpeed for motor 3 and 4 ?

Hello Ut Go very nice video , i subbed but i have a small issue so what happens is that i am using your same setup with shield and uno boards and two 18650 powerbank batteries to power the shield and a cable to power the uno. but when i run the 4 motors (small only) the ic on the shield heat up quickly in like 30 seconds. maybe it won't heat up without the cable connecting the uno to the laptop? please give confirmation. will appericiate it very much :)

@UtGoTech

3 ай бұрын

If you are giving separate power supply to motor Shield and arduino Uno then make sure that jumper is not connected.

Bro i want to make drone so should I have to put the same (200)speed code for the drone

@UtGoTech

Жыл бұрын

You can't make drone using these type of motors.

Thanks a lot. This helped lot for my projects. I want to control 4 N20 geared motors individually for camera automation and each motors will be controlled through GUI with momentary buttons. Hence suggest me if USB cable and power cable can be connected simultaneously for power and motor control...?

@UtGoTech

Жыл бұрын

Yes, you can connect usb cable and power cable simultaneously after removing the jumper in the motor shield.

@mallikarjun_m_acharya

Жыл бұрын

@@UtGoTech thank you so much

@UtGoTech

Жыл бұрын

Welcome

Hi! I was using this motor drive for powering up a DC motor (24v 0.5A), in its specifications it was stated, that it can handle voltage of 4.5...36V and up to 1.3A. I used it a lot but eventually, the capacitor which you can see from the left down on the 6:51 has exploded. Could you tell me what possibly could be a reason for that? Thank you!

@UtGoTech

2 жыл бұрын

Have you checked the capacitor rating. May be the capacitor used is not rated for 24V.

@user-sj6hn3lb8t

2 жыл бұрын

@@UtGoTech Well now I don't have that possibility))) But in the specification for this board for external power source it was stated that it should be able to handle up to 36V...

@UtGoTech

2 жыл бұрын

Most of these boards are cloned copies. That's why they may have some serious specifications issues.

@UtGoTech

Жыл бұрын

Look for the manufacturer site.

@UtGoTech

Жыл бұрын

👍

Which pins are the servos connected to if the motor shield is on a mega board

@UtGoTech

Жыл бұрын

Same as Arduino Uno

@duljayasavinu3814

Жыл бұрын

@@UtGoTech thanks

@UtGoTech

Жыл бұрын

Welcome

hi, for some reason my dc motors just make a hum noise and they do not move please help

@UtGoTech

Жыл бұрын

Check voltage is sufficient for motor or not and also confim that motor shaft is not jammed.

I want to take the speed instantly from a moving wheel thanks to the sensor and make the rotation speed of the dc motor with 50 rpm 24 v encoder, can you help me?

@UtGoTech

2 жыл бұрын

Which type of encoder you are using?

Great video! I am making a ball launching machine using a 12V 30W motor and a 16.8 Ah Lithium battery. Would this motor shield work with this setup? Thanks

@UtGoTech

2 жыл бұрын

No, you will motor powerfull motor driver.

@seanlyon2870

2 жыл бұрын

I just need to run my motor for one sec once every 5sec inteval. Would L298N be ok to use?

@seanlyon2870

2 жыл бұрын

@@UtGoTech Do you mean my motor is too powerful or I need a more powerful driver?

@UtGoTech

2 жыл бұрын

If you don't want to change the speed of motor the use relay.

@UtGoTech

2 жыл бұрын

Yes your motor is powerful that's why you need powerful driver.

Can I know, M1,M2,M3M4 of motor driver get connected to which pin of the arduino uno?

@UtGoTech

2 жыл бұрын

In the case of using DC motor, pin11 for Motor1, pin3 for Motor2, pin5 for Motor3, pin6 for Motor4 , 4, 7, 8 and 12 for all of them are in use.

hello, can you help me about how to accord your code for a Shield motor L298P ? for motors i use TP101 kit and it not work.

@UtGoTech

4 ай бұрын

This code uses Adafruit Motor Shield V1 Library which is designed for L293 motor drivers, you have to use different libraries which are designed for L298 Motor Driver.

Can you please help me I use 4 Bo Motor, 1servo motor for obstacle control car I use 11v rechargable battery but speed is low and car not moving motor run slowly and can you please explain why this happened

@UtGoTech

2 жыл бұрын

Check battery voltage during running. Maybe battery voltage is dropping.

@vikasthakurr253

2 жыл бұрын

@@UtGoTech sir I'm not unplug the jumper during connection maybe this is the problem..? Can you explain please 🙏is this a problem..?

My m1 and m2 needs external push to start while m3 and m4 works normal… do i need to add external capacitor on motor or my shield is defected??

@UtGoTech

8 ай бұрын

No, just increase the speed in code or increase the voltage of the motor driver.

@nihitnsr

8 ай бұрын

@@UtGoTech thank you…

@UtGoTech

8 ай бұрын

Welcome 😊

I just want to ask sir if this type of motor shield can be able to move 250v

@UtGoTech

Жыл бұрын

No

Bro how to write code for blutooth module hc-05 to control Arduino blutooth based car.

@UtGoTech

8 ай бұрын

You have to learn how to interface with HC-05 module.

After you put the last code for all motor after that we can remove the Arduino cable .? Will the code run if we only give power through motor shield

@UtGoTech

3 ай бұрын

Code will run even if Arduino cable is disconnected but for that you have to connect the jumper in the motor shield

Nice video. My question is; Since the motor shield sits directly on the arduino, can the arduino board be used to control any other device. Lets say an ESP8266 chip or any other motor driver

@UtGoTech

3 жыл бұрын

Yes. Although all the motors are connected there are still some gpio pins which are free and can be used for other purposes.

@olaoluwaolasehinde001

3 жыл бұрын

@@UtGoTech Thanks

Sir please make a mini atm or piggy bank using aurdino its a great idea for a awesome project with money detection amount and total money in bank

@UtGoTech

2 жыл бұрын

Ok sure

can it be used for a drone/helidrone? i recently bought L293D shield and the 2 motors I have to my helidrone are DC powered, but the L293D chip from the driver heats up. What do I do? Do I look for a different driver or do I add extra electronic parts for the motor? Keep in mind that the motor only vibrates and has a bad start (unless I start it manually). Thanks

@UtGoTech

2 жыл бұрын

This driver is not for drones. This driver is heating up due to high current.

@thebullet437

2 жыл бұрын

@@UtGoTech any other suggestions of shield/drivers for bigger motors?

@UtGoTech

2 жыл бұрын

Which motor you are using?

@thebullet437

2 жыл бұрын

@@UtGoTech it's very unknown since the drone was a product from a shop, so I have no idea, unless the physical size can give a clue.

@UtGoTech

2 жыл бұрын

Generally drones have BLDC motor or Cordless Motor. If the motors have 3 terminals then it is a BLDC motor. If it have only 2 terminals then it is a coreless motor. For BLDC motor use ESC as motor driver and for coreless use some kind of MOSFET driver.

Arduino uses 5vdc....if I want to puke around with 24v or 48vdc ....can I use Arduino shield....thanks pls

@UtGoTech

2 жыл бұрын

No

Hai sir I need a one help how to servo motor 90 degree & give a power supply with cct please explain

@UtGoTech

2 жыл бұрын

Just modify the code according to your need that is 90degree in your case. Just power it using 12volts.

How much voltage, amps i should give to arduino motor shield?

@UtGoTech

Жыл бұрын

Voltage should be between 6 to 12 volt and current about 2 Amps.

What kind of battery is being used to connect the l293d? Does a 6F22 9V battery sufficient to rotate 4 dc motors? Please let me know on any other options if not!!

@UtGoTech

Жыл бұрын

9V battery will not work. Use 2 lithium ion cells in series.

@bharateeshananth3808

Жыл бұрын

@@UtGoTech Thanks for replying! Should I have to use 18650 cells?

@UtGoTech

Жыл бұрын

Yes, you can use 18650 cells.

in some programme ia have seen a command as AF_MOTOR motor1(MOTOR_1, MOTOR12_64KHZ) WHAT DOES IT MEAN

@UtGoTech

6 ай бұрын

This is not a command. This is used to setup the control pins to control the motor.

Sir kindly make another video on connecting this motor sheild with any transmitter like Flysky I6 or Hot RC HT-6A using all four motors. Or please help me in connecting them

@UtGoTech

Жыл бұрын

Ok sure

Bhaiya I need your help🙏, I am making Bluetooth control fire fighting robot in which we will use hc05 Bluetooth module,ardiuno Uno,4 BO gear,one water pump,battery, ardiuno motor shield can you make video by using this all component plz in 2 or 3 days and also provide me code and diagram of circuit as well

@UtGoTech

6 ай бұрын

kzread.info/dash/bejne/gqWnj5WAl7q9Y9Y.htmlsi=PrNxhjvAtUQLqbH9 Make this robot then contact me, I will tell you what more to add for the fire fighting robot.

Can we control servo motors with Bluetooth module when servo connected to Motor Shield. Could u please explain it

@UtGoTech

2 жыл бұрын

Yes you can use servo motor, you have to use spare pins like A0 to A5

How much supply you have given to motor driver. I am using 9V battery but my battery is Discharging very fast. Could you please suggest which battery to use.

@UtGoTech

3 жыл бұрын

You can use lithium ion or lithium polymer batteries

Ref my last week clarification request. TKs much for your reply. When measured Voltage at the power input terminal of M.Shield it was 3.9 V. How the 9 V external power supply applied at Arduino board shows( 3.9V) at motor shield power input terminal inspire of jumper removal ? Is there any fault.? Anticipating your expertise comments. Reason for the above question ::: Two 6 VDC motors connected to M3 & M4 ports. 6 V lead acid battery connected to motor shield ( on measurement it is 6.4 V.) . Motor speed set to 240 Code uploaded to run both motors. When I checked the voltage at ports M3 &M4 it was 5.8 V.. Motor wires removed and Voltage measured It was 6.1 V . Why there is a big drop of 0.3 V at M3 & M4 terminal ( No drop at input terminal )

@UtGoTech

3 жыл бұрын

Reason for getting 5.8 volt when motor connected and running at speed 240 : Arduino board uses PWM signals to control the speed of the motors. Arduino board controls the duty cycle of the PWM signal to vary the speed of motor due to which you will get average voltage at the motor terminal which will always be less than the input power supply. As you are running motor at speed 240 that's why you are getting voltage of 5.8 volt in motor terminal. If you decrease the motor speed further then the voltage in the motor terminal also decreases because it is showing average voltage. If you increase the motor speed to its maximum, that is speed 255 then in the motor terminal you will get almost same voltage as input supply voltage. Reason for getting 6.1 volt when motors are disconnected.: When motors are disconnected no one is drawing power through the motor terminal and due to the presence of decoupling capacitors on each motor terminal you are getting higher voltage.

bro what is the power supply you have given to the motor shield

@UtGoTech

Жыл бұрын

I have used 12v power adapter.

Bro what if I Connect 7.4v DC Jack in the Arduino board will the shield works for 4 motors

@UtGoTech

Жыл бұрын

Yes, It will work but not for long due to heating of voltage regulator in Arduino board.

@srihari_dayalan

Жыл бұрын

@@UtGoTech yeah the same problem I have faced and my last shield damaged and now it's not working and also my last Arduino gone so please suggest me where should I give this 7.4v power and what should I do for that this thing for doing human following bot

@UtGoTech

Жыл бұрын

Connect power to motor shield.

Nice video! Is it possible to make the motors rotate randomly in Arduino?

@UtGoTech

Жыл бұрын

Yes. It's possible.

@Locomotive84

Жыл бұрын

@@UtGoTech Thanks.

@UtGoTech

Жыл бұрын

Welcome

Sir what is the max power supply that the shield can handle Can it handle 11 v 2400mAh,if not then what is the max mAh &voltage that it can handle.sir please help me

@UtGoTech

3 жыл бұрын

To be save give max upto 12 volts. mAh is not issue.