Obstacle Avoiding Robot Car Using An Arduino
Тәжірибелік нұсқаулар және стиль
In this video, I’ll be showing you how to build your own Arduino based obstacle avoiding robot car. The car uses a servo mounted ultrasonic sensor to detect objects in front of and on either side of the car and an L293D DC motor driver shield to drive four geared motors, one on each wheel. An Arduino Uno underneath the shield controls the motor shield, ultrasonic sensor, and the servo.
The car drives itself forward until an object comes within the range of the sensor. The car then monitors the object until it is within the minimum distance and then stops moving. The servo is then used to turn the ultrasonic sensor left and the right, taking distance measurements in each direction. The car then decides which direction to turn based on which side has more distance available to move, then turns and continues on until the next object is detected. If both sides are blocked, the car will turn around and drive back out the way it came.
Full step by step written guide along with print files & code - www.the-diy-life.com/arduino-...
Components Required & Purchase Links
• Arduino Uno - amzn.to/2OgoMvv
• L293D Motor Driver Shield- amzn.to/3fpTzld
• Micro Servo - amzn.to/380rddp
• Ultrasonic Sensor Module - amzn.to/2ZktM8G
• 4 x Geared DC Motors & Wheels - amzn.to/3dAZghI
• 9-12V Battery Pack
• 8 x M3 x 15mm Socket Head Screws - amzn.to/2V7vaZ5
• Ribbon Cable - amzn.to/340xB3B
• Header Pins - amzn.to/2wY3k9g
If you've got any suggestions for future Arduino or electronics projects, let me know in the comments section.
Пікірлер: 403
Amazing tutorial Michail! short, precise, complete and simply explained. Thank you very much keep up the good work.
@MichaelKlements
Жыл бұрын
Thanks Mohammad
This is simply wow! So well explained
Great project! Thankyou for your work on this. Just changed a few speed settings for mine, works great.
@MichaelKlements
3 жыл бұрын
That's great to hear!
@GelFireQueensland
3 жыл бұрын
@@MichaelKlements Hi! I've since noticed it only ever turns one direction, regardless of obstacles location. I can reverse the turn direction by changing AF_DCMotor assignments Left to Right, but I can't get it to decide to best turn direction, it only goes same way each time. The servo was incorrectly looking right first, but fixing that didn't fix the problem. I downloaded your Code again in case I accidently changed something that matters, no go. Also played around with the 'int checkDirection()' in curiosity.. Anyway maybe you can suggest an answer if you have time. Thanks from QLD Australia.
Thank you so much Michael! I'm really grateful ❤❤ Especially when you linked the again products,, you've got my respect man! Not only are you an amazing electronic device maker but also you're an amazing guy for helping us rookies so much 💗
@MichaelKlements
Жыл бұрын
Thanks for the feedback and support Henin!
thank you so much , i just learned about the part when you can put a max wait int the pulseIn() function. appreciate it :)
bro loved the project thank you so much
That's an awesome car dude. Sounds like you from GP.
Very nice video. The only thing I am missing is how to access the pins on the top of the motor shield. But this video is exactly what I was looking for.
HI Michael Klements , you are very great .
Amazing project ! Just Additional Information... Ask permission Mr. Michael Klements for those of you who are new to assembling, then there is a problem with the speed of the motor.. the solution is: 1. Change the byte value of motorSpeed 2. check the condition of the battery, is it still good or not 3. check the state of the gear motors (dynamo) Thank you for your attention Greetings from Ponorogo, East Java, Indonesia
@lilianseverinodasilva94
5 ай бұрын
What do you suggest to use instead of byte?
thanks man it helped in my school project
tysm bro video was too good with nice explaination
Thank you very much for this
this is so cool!!!
Thanks it is most helpful for me
Hey Michael , Loved how you made it look so easy but I need help I'm facing a problem.. I have my trig and echo pin connected to A1 and A0 respectively and I replaced the no. in your code to A1 A0, and when I turn on the car the motors dont run and servo motor is also not moving.. please help me out here:(
Thanks a lot brother ❤️❤️
thank you so much for the help, it was very intresting and emosjonell. this expirience was life changeing. I have many of these robots now wich roams my grochery stores. i'am now a proffesional robot maker. i build robots, hand made. im rich now.
Great!.. the circuit diagram please 🥺
very good one i did it everything was fine and gd
@MichaelKlements
3 жыл бұрын
Thats great!
Hola profe. felicitaciones por su trabajo el único problema que tengo es que no hace los giros, o solo avanza o solo retrocede, gracias por la respuesta saludos de Lima _Perú
@arhantmovva4867
2 жыл бұрын
revisa el código y los cables
Hi Michael, great project. i am relatively new to Arduino and understand most of the sketch. However I would like to understand the difference between calling a function following a void command such as "void stopMove() and the call to distance=getDistance() where the getDistance code starts with the statement "int getDistance()" why isn't getDistance also a void statement? cheers.
@MichaelKlements
2 жыл бұрын
Hi Kerrie, There are two different types of functions, ones starting with void just carry out the code in the function and ones that start with int (or String, char, Boolean etc.) are functions that return an a variable or “answer” of that type. void stopMove just tells the motors to stop. Where int getDistance returns the distance measured to the object as an int variable type. Hope that helps make it clear
Can i do this with my old toy Car which can turn right and left with the help of gear motor How can plug that may also in the Motordrive shield
Good luck.
Hey, this video was amazing. Actually, I wanted to know how you fit the pins on thr motor driver shield? Thanks!
@MichaelKlements
2 жыл бұрын
I just soldered them onto the board myself.
@abhishekrathore9470
2 жыл бұрын
Bro aapka project work kr rha hai?
@jimmyjummy5132
Жыл бұрын
@@abhishekrathore9470 yea man fully agree
Oh my god, How can I ever thank you???? My car worked soo well, there's just one thing. The speed is too low, but other than that, everything is working great.
@fahmidhaque2494
9 ай бұрын
Can you help me with the Speed issue?
@MichaelKlements
9 ай бұрын
The only way to increase the speed is to use a higher supply voltage - but still stay under the maximum voltage that the driver shield can handle.
@fahmidhaque2494
8 ай бұрын
@@MichaelKlements Oh okay Thanks for the information.
How did you solder on pin 13? I’m struggling with this one!
Hi Michael, thanks for the project! I did everything and made some changes on my own and the car works good! Just one issue, the servo motor is spinning too fast, so fast that it removes the wiring sometimes. Do you have any idea on how to fix this, like how to slow down the servo?
@MichaelKlements
Ай бұрын
Hi Techysoham, thats great to hear. There are some Arduino libraries that offer servo speed control, the other option would be to create a functional that moves the servo in single single-degree increments with a small delay between each step.
Hola, estoy haciendo un automóvil Arduino para un proyecto escolar sigue todos los pasos en el video pero el carro no camina / tengo tarjeta R3 Wifi MCU ATmega 328p / Wifi ESP8266 / Usb ch320g - se tiene que hacer alguna configuración diferente ?
Profesor otra cosita el robot usa una batería o 2 baterías siempre uso 2 pero ahora no esta claro como usar o 1 bat o 2 bat. por favor quería una respuesta gracias.
Hello, great project! I've run into a few problems and by modifying the code a little I managed to find the solutions. Although there is one problem that I can't find a way to fix. The ultrasonic module only detects a wall once, it stops after the 2nd wall, but the engines still continue forward into the wall. Could you help me, please? (My modifications did not cause this problem since when I used the original code it didn't work either)
@ggplayer2162
3 жыл бұрын
can u copy and paste ur code plz need help
Hi i need help i want to add gsm module and pir sensor on this project can you help me where to insert the codes
You can make a video on how to make sensor lights using Arduino Uno and ultrasonic sensor.
@MichaelKlements
3 жыл бұрын
Thanks for the suggestion, I'll have a look at this.
@artigupta7852
3 жыл бұрын
@@MichaelKlements Can you give me the website on which you created the 3d model
@MichaelKlements
3 жыл бұрын
@@artigupta7852 it was drawn in Tinkercad
i dont have the 13 slot on my board so where can i put it
Does anyone have the circuit simulation of this arduino in proteus 8?
Thanks for the video, why didn't you just solder the wire to the board directly on pin 13 instead of using a pinhead?
@MichaelKlements
Жыл бұрын
Only so that it can be removed if required
@GG-sd2dr
Жыл бұрын
@@MichaelKlements oh, ok thanks!
What are the library you installed for the code
Can you please share tinkercard link of project and bottom part?
I am in fifth and I have make this project today very easily It's too easy
How did you attach the wires to geared DC motors? And did you solder or just inserted the pin heads on pin no. 2 and 13? Thanks
@MichaelKlements
2 жыл бұрын
They're soldered to the motors, the headers are also soldered to pins 2 and 13.
Would this concept work on a larger scale car/kart?
@MichaelKlements
17 күн бұрын
Yes, you'd just need to use larger motors and motor drivers.
Bro which type of battery will use🤔
Hi Michael, it would be a great help if you tell me what I'm doing wrong here. Even though I copied your code the robot doesn't function correctly. when infront of a wall when activated it checks for spaces to move and once it finds a way it moves and doesn't stop again when it encounters any obstacles. I've seen some other people have the same problem as I. I made sure that my connections are correct so what might be the problem. Thank you very much.
@PlexusSkIllz
Жыл бұрын
For anybody wondering. I fixed this problem by adding return; after moveForward() in the if statement that's in the void loop
Hi Michael, I understand this project is 3 years old however do you believe with some adjustments to the code an analog servo motor can be used instead?
@MichaelKlements
3 ай бұрын
Like and analog RC servo motor or one that requires a different driver?
How to change the code to adjust the speed of motors?
Today i made this in my college... ❤️
@julkarnain3328
Жыл бұрын
Does it work I am not getting the code the code is wrong
@worldVK1704
Жыл бұрын
@@julkarnain3328 which device you used to code the Arduino...... Pc.. Laptop or mobile..?
@pranavrk8639
Жыл бұрын
How
@romnathbaba3287
Жыл бұрын
@@julkarnain3328 Ask it in chat gpt Thank me later😮
@ravikumara7496
Жыл бұрын
Total cost
Mate what batteries do you use to power this thing ? I thing that's the most important aspect of this project (you skipped the part where you install the batteries) since many of us who're trying to get this to run use 9V batteries and that simply isn't the optimal power source
@MichaelKlements
4 ай бұрын
Either use 4 x AA batteries in a pack or use a 2 or 3 cell LiPo battery (that's what I've used).
@ZVEKOfficial
4 ай бұрын
@@MichaelKlements Yeah well I bought a 4 pack and a 6 pack AA holder. The 4 pack doesn't have enough voltage (1.5 x 4) as the L293D driver has a voltage drop of around 1.8V so the motors spin reaaaallly slowly. Nevermind turning left/right. The 6 pack is also meh to be honest. I think I need to buy a high voltage high capacity LiPo battery like you mentioned to run this at its full potential. Or maybe 2x 18650 Li Ion battery
So I'm a little confused. In the description, you list header pins as a part, but I am unable to find where they are actually used. Could you describe where they are used and also why they are needed.
@MichaelKlements
3 жыл бұрын
You need the header pins to solder to the motor driver shield so that you can plug the ultrasonic sensor into it. These pins aren't installed on the board when you buy it. You'll also need female pins to make up the cable to the sensor.
@minroiwijayarathne1965
3 жыл бұрын
@@MichaelKlements do you have a link from which I could buy header pins?
Hello brother, I am unable to understand how you connected the female header pin to pin 13. Can you please explain?
@MichaelKlements
2 жыл бұрын
I had to solder additional header pins onto my shield in order to plug it in - alternately you could just solder the wire directly onto the shield.
Hello Micheal, Great video! I did want to ask what voltage are you using to supply the car? I am using 6V. Is that fine?
@MichaelKlements
Жыл бұрын
I use either a 2cell or 3 cell lipo, so 7.6V or 11.4V. It's not so much the voltage that is the issue, you need a battery pack than can provide enough current for four motors to run. 6V would probably be fine if the pack can supply each motor an amp or so on startup.
@revantpandey8893
Жыл бұрын
@@MichaelKlements Can 4AA rehargable batteries supply an amp to each motor? Thank you for the reply!
@MichaelKlements
Жыл бұрын
Probably not unless they're really good quality ones. I'd suggest using a lithium ion battery pack or a holder for two or three 18650 cells.
@revantpandey8893
Жыл бұрын
@@MichaelKlements Thank you so much! That's probably the reason why my car is not working!
@revantpandey8893
Жыл бұрын
@@MichaelKlements Hello Michael! I am using a 12V adapter currently to power my car but I want it to be wireless. Could you please recommend a LIPO battery? Either send a link or just tell me here? That would be great help thank you!!!!
Bro, Is there a way where i can see the other side of the motor driver shield? i want to see how it was soldered on the other side because as i am lacking of pins to connect lots of sensor given that this ln293d occupies the whole arduino pins... Your video has brought me some hope.
@MichaelKlements
2 жыл бұрын
There is some more information in my blog post linked in the video description. I haven't done anything on the bottom of the shield, I only added pins to the top.
@diye.28
2 жыл бұрын
I will take a look right now. So, only 2 and 13 can be soldered? It’s a pity that this board takes all the pins of arduino. I’ve got lots of sensors to connect but sadly the board takes them all. I have another question, is there a way we can connect the l293d and the board sensor shield v5.0? So I can have more pinouts for sensors, leds, buzzers and the like. Thank you 😊
@MichaelKlements
2 жыл бұрын
The two drivers unfortunately require that many pins to control them. If the driver is using the pins then you won't be able to connect an IO expansion board at the same time. You'd be best off finding an I2C motor driver then and that'll free up all of the digital pins for your sensors.
@diye.28
2 жыл бұрын
Thank you for you kindly answer. I’m a beginner at this and I have to use mblock which is more code friendly, that being said, I have no idea how can I connect two arduinos together so I can use one for the ln293d and control the motors and the other arduino with the sensor shield v5 and have a wide range of digital pin outs. I would kindly be grateful if you have any idea how 🥹
Can I make it 2 wheeled ???
How to customise how near can the distance of the robot be with the obstacle before turning away. I want my robot to be about 10cm distance from the obstacle
@MichaelKlements
2 жыл бұрын
Just change the parameter stopDist in the code to 10
Heyy thanks a lot for this tutorial now i can finally start making this myself, although one doubt.. while executing your code it shows 'servoLook' was not declared in this scope as the error message... could you help me pls
@divyadeenu1686
Жыл бұрын
Are you sure you have the library?
@sumitpandey-tw7rm
Жыл бұрын
@@divyadeenu1686 kyu bana raha hea line 5 or 6 mea jaha bytes declare kiya hea vaha pe dekho servo servolock likha hea ki mit gaya. Tumhara sevo ka object nahi bana hea. Servo library. Nahi hone pe vo #include pe error deta.
where can I find the wiring diagram?
how to code the sumobot not avoiding the object by attacking how to code using the components of obstacle avoiding robot
I also make a car but it is not working can you help me to make it
Hello I am new to Arduino And servo motor and ultrasonic sensor are working good But when it's time to move motors their Speed is very low and sometimes not even moving If it is the matter of battery pls suggest Which to use Or some different problem.
@MichaelKlements
3 жыл бұрын
Hi Kapil, You can adjust the motor speed in the code by increasing the motorSpeed variable. If that doesn't help then your batteries are probably underpowered, I usually use lithium-ion or lithium-polymer batteries for these projects.
Hey man where to put the battery
hey please anyone tell this work..? please🙏
The servo and the ultra sonic sensor work perfectly. but only 1 motor is working and the others are not !! is it because am using 9v battery ? and i have attach headers pin on A0 - A1 for the echo and trig instead the pins you are using , what changes i can do in order to use your code but with my current pins ? Thanks alot Mr Micheal
@MichaelKlements
3 жыл бұрын
It might be related to the 9V battery, these generally aren't able to provide enough current for four motors.
@laxmikantreddy6567
2 жыл бұрын
bro. will it work if we change header pin to A0 and A1
Is there any batery
Could you help me out here! I am using a 9v battery as power supply, though it is powering up the arduino board and motor driver it is not helping to drive the motors and servo motor, but when i connect to my laptop to upload the code it is poweringup enough to drive the motors and servo.
@MichaelKlements
2 жыл бұрын
A 9V battery isn't able to provide enough current to drive four motors. It works when powered by USB as well as it is supplementing the shortfall. You need to use a better battery pack.
hey could we plug the power supply into the Arduino Uno instead of the driver shield?
@MichaelKlements
8 ай бұрын
The motor driver pulls too much current to power it through the Arduino, you should power the driver and allow the driver to power the Arduino.
Hi Michael Kelements, Can we use a 9volts battery in this
@MichaelKlements
Жыл бұрын
9V block batteries aren't able to supply enough current to drive 4 motors.
where is the servo library link
Where are these parts available?
please help me master... i want to install a buzzer to on the smart car, so that it sounds when sensor reads an object, please help me make the coding. Thank you in advance
Please couldn you provide circuit diagram
How many pins of Arduino are remains usable after connecting L293D shield means which are those pins which are not connected to shield
@MichaelKlements
3 жыл бұрын
Pins 2, 13 and A0-A5
Hi sir can you share Arduino circuit please....
hello Mr. Klements, I tried putting a 3 x 3.7V rechargeable battery with a total of 11.1V but when I added 5V to it giving a total of whopping 16.1V, the Arduino Mega 2560 stopped working. Did I supply too much current? is the 11.1V enough for the 4 motors?
@MichaelKlements
2 ай бұрын
I'm not sure how or why you added 5V to it, 11.1V is enough to supply both the motor shield and the Arduino. That said, 16.1V also should not have damaged the Arduino Mega since these can typically handle a supply voltage of up to 20V.
can i use hw battries
How long does your car keep moving if u don't disconnect the power at all ?
@MichaelKlements
2 жыл бұрын
Around 5-10 minutes depending on how fast it is driving and how many turns it is making.
What type of battery and it's power you used in this
@MichaelKlements
2 жыл бұрын
I used a 3 cell, 850mAh LiPo
Could you modify the program for me?, I'm a beginner in robotics and I don't know how to program, I have the same project but I don't have a servo motor, could you modify?
We can do the coting in mobile
Because I want to put the photos of it
Hello Bro Can You Please Say Me How To Decrease the speed of motors and if reduced the turning speed also decreases
@MichaelKlements
Жыл бұрын
Just adjust the motor speed variables at the begining of the code, the turning speed is scaled from these so will also reduce
what software did you use for the making of the model in 3D?
@MichaelKlements
Жыл бұрын
TinkerCAD
Where is the switch and battery? And how is it wired in relation to all the components. Sorry I am new to circuits.
@MichaelKlements
2 жыл бұрын
There is a blog post linked in the video description that has some more detail on the wiring and components used.
I have a problem. My Arduino car doesn’t want ti drive perfectly straight. Pls help
Can I use Arduino UNO R3 SMD Atmega328P Board - Clone Compatible Model
@MichaelKlements
2 жыл бұрын
Yes you can use an Uno clone board, as long as it has the same pinout as the original Uno it should work with the motor driver shield.
Hi, I would like to know how did the wheels turn left and right if you did not use servo motor on the wheels?
@MichaelKlements
2 жыл бұрын
The wheels don't physically steer left or right. The difference in motor speed between the left and right side turns the car.
@elizacrescini9444
2 жыл бұрын
@@MichaelKlements thank you so much!
Can you please share circuit diagram
Greetings Michael, I have a question regarding the rover. From halt it propagates forward and then at specific stopdistance(which i believe is set to be in cm), and then stops. THe servo moves from 0 to 90 to 180. Then the rover goes backwards till specific distance. But it never turn around. It always goes forwards and backwards. I have used your ocde and modified the tie daelys for some lines but it doesnt seem to turn at all. And yes I have tested the rover in spaces whereleft is more than space on the right etc.. What can I do ? I would really appreciate the help. All the rover turn setting are as such. If Turn left... right motors turn FORWARD, Left motors turn backward...vice versa for Turn Right. I do not know what to do. Please help me.
@MichaelKlements
Жыл бұрын
There is not steering mechanism on the car, so to turn left the right wheels run forward and the left wheels run backwards, if the motor speeds are set correctly then the car will rotate on the spot (it shouldn't move forwards or backwards while turning). It sounds like your motor speeds have been adjusted incorrectly, so one side is probably overpowering the other side.
@niranjanremesh6992
Жыл бұрын
@@MichaelKlements hi michael could u reply to my query pls
i have done everything shown in the vid but when i upload the code it doesn't move at all can anyone help plzzz
Hey, how can i find codes for it?
Hey, really cool video. I have tried it on my 4wheel Arduino car, but the car only moves back not forward. Do you know why is that?
@lestertang2102
3 жыл бұрын
By the way, the Arduino car kit I got do not allow me to swap the wires on terminal. Is there other way to fix it? and in your code, the rightback 1, is the number of the pin?
@MichaelKlements
3 жыл бұрын
Thanks Lester. Are you using the same motor driver shield? Try stripping the code down to just run forward and then backward and see if it works, that'll point out if it is a code problem or hardware problem. No, the numbers after rightback and leftback etc. refer to the motor output numbers, not pin numbers. These tell the code which motor output is driving which wheel location.
@lestertang2102
3 жыл бұрын
@@MichaelKlements Thank you! Do you think we can make a drift car based on this kit?
@MichaelKlements
3 жыл бұрын
These motors aren't really "high performance" motors, so probably wouldn't produce enough torque to get the car to drift. I think you'd be better off using brushless motors and some brushless PWM drivers which you could drive from an Arduino if you'd like.
Where can we get the 3D print file for chesse
Hi, so I don't quiet understand what did you do to the 12v battery, do you just put it in the middle section and wire it to the board or to the motors?
@MichaelKlements
Жыл бұрын
It is connected to the motor shield's power input, the shield then powers the Arduino
@Lepo69
Жыл бұрын
@@MichaelKlements Do you suggest any batterypacks that workf or this rc car or no?
will it stop at the stairs or will it drive down until it flips?
@MichaelKlements
2 жыл бұрын
This doesn't detect edges, only obstacles in front of the car.
Is there any other cheaper option other than the arduino uno
@MichaelKlements
Жыл бұрын
Not that's compatable with the motor shield, you can get clone Arduinos for a few dollars on Aliexpress
Plz give me a The program code it's not working I can't download it
Hey my car is not moving what shall I do
what that means?
Great video! But how did you upload your code to the robot?
@blidzy_
Жыл бұрын
yep same question
@divyadeenu1686
Жыл бұрын
By connecting the cable to the uno. After that copy paste the code or open the .zip file he left for us to download. Then simply click upload. You must do this in the Arduino IDE software. The latest version is 2.0.3
Appreciate the project. I've been trying to implelement this on my project and i noticed something in the code can you enlighten me? if(distance >= stopDist) { moveForward(); } while(distance >= stopDist) { distance = getDistance(); delay(250); } stopMove(); int turnDir = checkDirection(); Serial.print(turnDir); shouldn't there be an "else" above the stopMove(); function? Since we defined an if argument? I don't get using while loop after "if" without the else statement. Thanks in advance.
@MichaelKlements
2 жыл бұрын
I think you're misunderstanding what is happening in each function. The if statement checks if there is enough space infront of the car to move. If there is then it tells the car to move. Since nothing then tells the car to stop, the car will carry on moving until it is told to stop. The while loop then continuously checks that there is still space in front of the car and will carry on running as long as there is still space. As soon as there isn't space in front of the car, the while loop stops running and the code runs the stopMove command which then stops the car.
@nurbanu1283
2 жыл бұрын
@@MichaelKlements Oh, i got it now it makes perfect sense. Thank you for your response!
I have a question about the yellow-capped component labeled "PW" on the motor shield. Additionally, I've developed a car using the same procedure and utilizing two 3.7V batteries each. However, I've encountered two problems: 1- When I unplug the USB, the car stops working. 2- The batteries seem unable to power all four motors to move the car. Initially, the setup worked fine during testing, but these issues arose later on. Could you please provide assistance on how to address these problems? and what specific Batteries and how many of them I need and what volatge.Thanks In adavnce
@MichaelKlements
3 ай бұрын
I assume you're talking about the jumper labelled "PWR" - mine is black not yellow. This is jumper that either allows the shield to supply power to the Arduino or disables this feature if the voltage is outside of the Arduino's range. If you're supplying power to the shield only then you need to have a jumper on here to power the Arduino as well. Using 3.7V batteries, you would need them to be connected in series and ensure that they can supply enough current to drive the motors.
@Shalaby2002
3 ай бұрын
@@MichaelKlements Thank you for your response. Yeah Man , you got me correctly. I was referring to the yellow PWR in my case 😂. From your comment, I gather that I need two batteries, providing approximately 7.2V and 1200mA. In this scenario, I simply keep the PWR turned off as it's. COZ I'm afraid of messing things up
@MichaelKlements
3 ай бұрын
You need a supply voltage of at least 4.5V, so either one 7.4V battery or two 3.7V batteries in series would work. If the jumper isn't on then you need to provide the Arduino with it's own power source as well.
Can you provide a link for buying robot chassis ???
@MichaelKlements
3 жыл бұрын
The chassis is just 3D printed, the parts are downloadable through the link in the video description