How to remove Drain Hose and clean. kzread.info/dash/bejne/Y5hoy8eilNG6erQ.html kzread.info/dash/bejne/daatx8Vpk7eZgrg.html 😎👍

I cannot thank you enough for your thorough and descriptive video! Our Maytag Neptune front load washer had stopped draining so we watched this video and another of yours and decided to tackle the job ourselves. We followed your instructions, removed the hose and pump and found a coin lodged in the pump. Removed it, put everything back together and washer works perfectly again! THANK YOU!!

@DIYwithMichaelBorders

5 жыл бұрын

Kathryn Selby Awesome Awesome & thanks for watching. You are so welcome! We really appreciate your comment. 😀 We absolutely love reading comments like yours. We really enjoy making these videos & helping out our fellow DIY’ers. Let us know if you have any questions. Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

@paulpoco22

4 жыл бұрын

If the washer was old enough and yes you cleared the coin, but while all apart just replace the drain pump, then you never need to tackle the drain pump for 10 to 15 years.

Your detailed video and instructions allowed this senior citizen replace the defective drain pump & this gal is now washing clothes again ! Thanks soooo much ! I’m liberated !

@DIYwithMichaelBorders

Жыл бұрын

Good morning, we are hanging out drinking our morning coffee & answering questions for the DIY community. We love reading comments like yours, awesome job making it a DIY project. We are always here to help answer questions, enjoy your upcoming weekend debby. 😎👍

Great video. We fixed my washer with your clear directions, steady filming and step by step instructions. Thank you

@DIYwithMichaelBorders

4 жыл бұрын

Margaret Chiappetta Great to hear & we appreciate you sharing. A rewarding feeling. Welcome to the DIY Raptor Club. Us fellow DIY’ers need to stick together! 😎👍🔧🔩

I found the drain hose clogged with the material from a rug, it was almost like sandy paper. I used a clothes hanger wire (with sharp end folded back to prevent hose puncture) to losen up the material, then a big shop vac i had to suck out the debris and water. Restarted it on a rinse and spin and thank God the pump was ok, its running again! These units are now coming up on 17 years old with minimal parts replacement, no wonder that Maytag repairman is always lounging around on the commercials lol ! Good video helpful!!

@DIYwithMichaelBorders

11 ай бұрын

Thanks for watching, that’s great to hear. 17 years strong, we love to hear that. Keep it healthy and running. 😎👍

THANK YOU SO MUCH! I ordered a pump weeks ago after watching. I'm quarantined now in New Orleans and my roommate and I finally spent some time with your video and fixed it! A great, productive way to spend the day. Hope you and yours are well!

@DIYwithMichaelBorders

4 жыл бұрын

Alana Pryor Ackerman You just made our day. We love reading comments like yours. Awesome job & welcome to the DIY Club. 😀 Us fellow DIY’ers need to stick together. Let us know if you have any questions. Please subscribe to the channel and Ring your KZread Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

Excellent filming and instruction. Very professional narration! You could do this for a living.

@DIYwithMichaelBorders

Жыл бұрын

Thanks Peter, that means the world to us. Thanks for watching. 👍

Thanks for the video information. Very helpful, concise, straightforward, and simple step-by-step. 👍

@DIYwithMichaelBorders

7 ай бұрын

Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community. You are welcome, and we are honored you took the time to reach out to us. That’s our goal, getting you the info you need without wasting your valuable time. 👍 Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

Thanks for this information. I thought my Maytag might be a goner cause it wasn't draining. Turns out there was a broken up ballpoint pen and four baby socks from my tenants of two years back lodged just in front of the pump intake. Your very explicit step by step instructions and admonishments were super helpful. All's well now.

@DIYwithMichaelBorders

2 жыл бұрын

Awesome, ballpoint pens can definitely cause havoc on machine. We appreciate you sharing this Curt. Hopefully many stress free days ahead for you. Many more helpful videos to come. 😎👍

Thanks for info, i found a quarter in my pump. cleaned out everything works great. saved me a ton of money

@DIYwithMichaelBorders

6 жыл бұрын

Greg Krug Very cool & thanks for sharing your comment & watching video! We love hearing experiences like yours & how you were able to save some 💰 💰. Below is a link to our Appliance/Home Repair Video PlayList. It contains several videos that you can benefit from including additional videos on your Washing Machine. Definitely check those out. kzread.info/head/PLjCXOz8TSkZmG-ZbhhKPj4Vh3K3MDPXii Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

Thank you. I just pulled out a rock the size of a quarter & it’s draining again! You saved me money!!!

@DIYwithMichaelBorders

3 жыл бұрын

Kari Tacoma So happy to help & we appreciate you watching. Saving money is always a good thing. 😎👍🔧🔩

good video and very precise,now I can fix that Maytag washer that I dragged here from Michigan{Live in new York now,thanks and keep em coming....

@DIYwithMichaelBorders

5 жыл бұрын

john graham Thanks for watching & sharing your comment, we really appreciate it! We are happy to hear the video helped. This is a pretty friendly DIY project. Hopefully your washer works great in New York! 😀👍 Let us know if you have any questions, we are here to help! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

Your video is awesome. It will help many DIY enthusiasts. Thank you.

Thanks a lot .due to your guidance we fix our washer

@DIYwithMichaelBorders

6 жыл бұрын

Manoj gupta Awesome Awesome thanks for checking out the video. We are glad to hear the video helped. Thanks for sharing your comment. Please subscribe to the channel and turn on your KZread notification Bell that would be awesome thanks again! Also below is a link to our Appliance/Home Repair Video PlayList. It has several videos that you can benefit from including additional videos on your washing machine. Definitely check those out! 😎👍🔧🔩

bro naimeth, you are the man! mine turned out to be a penny perfectly obstructing the outlet from the pump. once it cut off flow the pump obviously was impacted and then spin cycle was also cut off. managed to get the penny out, cleaned everything out and put it back together. everything is working all good now. thanks for the diagnosing and disassembly info. will keep an eye on the pump to see if there is any long term issues as it may have been working harder than needed for a while.

@DIYwithMichaelBorders

6 жыл бұрын

Kyle C Awesome Awesome & thanks for sharing your experience! Below are a few additional video links that cover your washing machine! Definitely check those out! kzread.info/dash/bejne/a4GjxruqisbAZdY.html kzread.info/dash/bejne/daatx8Vpk7eZgrg.html Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again!

Awesome video! Thank you so much! Drain hose had a guitar pic and a nickel in it🙄. My son fixed it within a few minutes, saving me $$$.👍

@DIYwithMichaelBorders

3 жыл бұрын

Very cool & we appreciate you reaching out to us. Guitar pic’s can definitely sneak into the filter. 😁 Let us know if you have any questions. Us fellow DIY’ers need to stick together. 😎👍🔧🔩

Thank you for this video, my Samsung washing machine is working now after replaced the pump, thank you so much.

@DIYwithMichaelBorders

5 жыл бұрын

Roger Au Awesome Awesome you are very welcome. We are so happy to hear the video helped. It’s always a bummer when your Appliances start acting goofy. Let us know if you have any questions along the way, we are here to help! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! Also, if you’re interested, below is a link to our Appliance/Home Repair Video PlayList. It contains several videos that you may find beneficial including additional videos on your Washing Machine. 😎👍🔧🔩 kzread.info/head/PLjCXOz8TSkZmG-ZbhhKPj4Vh3K3MDPXii

@paulpoco22

4 жыл бұрын

The Maytag Neptune has Samsung parts in them, the Maytag parts are 3 to 5 times more expensive than the same Samsung part.

I'm most impressed you did this whole thing one-handed.

@DIYwithMichaelBorders

4 жыл бұрын

ElementalExposure Thanks for watching. Hopefully the video helps you get your project done successfully. Many more helpful videos to come! 😀 Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again. 😎👍🔧🔩

@paulpoco22

4 жыл бұрын

@@DIYwithMichaelBorders you probably don't remember how much room you needed to turn it sideways? In 2007 I built a platform to raise the both unit at a nicer height. So I don't think I have enough room to turn is sideways and washer is on left and dryer on right side. I probably will have to disconnect the water supply and pull it all the way out. I notice our kitchen chair seats are the same height as the bottom of washer. I thought I could get the washer partially on one seat facing washer, then pull more and get 2 other chairs on either side.

@DIYwithMichaelBorders

4 жыл бұрын

paul poco Sounds like us...🤔

Thanks so much for not mentioning the bolt size...

@DIYwithMichaelBorders

Жыл бұрын

You’re welcome, we are happy to help. Thanks for watching.

You just saved me a bunch of money!!.... SUBBED!!

@DIYwithMichaelBorders

6 жыл бұрын

KillaCommieFerMommie Awesome Awesome & Thanks for checking out the video and sharing your comment. We appreciate you taking the time to reach out to us. We are so glad the video helped. We have a few additional videos that reference the MayTag Washing Machine. The links are below. Definitely check those out as they will definitely come in handy. Clogged Drain Hose Video: kzread.info/dash/bejne/daatx8Vpk7eZgrg.html Washer Shakes/Wobbles “Shock Absorbers” kzread.info/dash/bejne/a4GjxruqisbAZdY.html Let us know if you have any additional questions along the way we are here to help. Please subscribe to the channel and turn on your KZread notifications that would be awesome thanks again 😎👍🔧🔩

I hope this can work on 2006 Samsung WF306LAWXAC washer with part DC96-0141A, this video shows exactly steps what I am looking for, waiting for the pump in this few days. Thank you Michael Borders

@DIYwithMichaelBorders

5 жыл бұрын

Roger Au Awesome Awesome & thanks for sharing your experience. Definitely keep us posted & let us know if you have any questions, we are here to help! We look forward to hearing back from you & hear about your progress with getting your washer back up & running properly & efficiently. Keep us posted! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

thank you so much! washer broke on the way to see the in-laws... almost thanked it lol!!! anyways, great video.

@DIYwithMichaelBorders

3 жыл бұрын

Thanks for watching & we are happy to hear it is all fixed. Let us know if you have any questions. 😎👍🔧🔩

Very helpful thanks a bunch

@DIYwithMichaelBorders

4 жыл бұрын

Johnny Arnaud Great to hear & we appreciate you watching Johnny. Sounds like you’re back up and running. Let us know if you have any questions. Us fellow DIY’ers need to stick together. 😎👍🔧🔩

You are the Dude!!!!!😊

@DIYwithMichaelBorders

Жыл бұрын

That’s very kind of you to share Roger, we appreciate that. Special thanks to YOU for taking the time to share this on your Friday afternoon. Hope all is well. 😎👍

Thanks, my pump clogged. I pull out coins & mask filter. Got it back up running & didnt have to a new pump.

@DIYwithMichaelBorders

3 жыл бұрын

Sharon Alexander Thanks for watching & that’s great to hear. Let us know if you have any questions. Us fellow DIY’ers need to stick together! 😎👍🔧🔩

Wow! Ur good

@DIYwithMichaelBorders

5 жыл бұрын

milena deltorto Thanks for watching & we really appreciate your comment. 😀 We really enjoy making these videos & helping out our fellow DIY’ers. Let us know if you have any questions. Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

I bought this as a replacement drain pump: SUPCO LP1414A Washer Pump It comes as one unit with the metal plate already attached.

@DIYwithMichaelBorders

4 жыл бұрын

paul poco Thanks for watching, that’s kinda cool. We hope you enjoyed the video. Us fellow DIY’ers need to stick together! 😎👍🔧🔩

@paulpoco22

3 жыл бұрын

@@DIYwithMichaelBorders Replaced the drain pump. As soon as I took off the drain hose to the back of the machine, a guitar pick dropped out. So that would probably move into the right position to block the hose.

@DIYwithMichaelBorders

3 жыл бұрын

paul poco Interesting...🤔 Thanks for watching & sharing. Hopefully you’re back up & running. 😎👍🔧🔩

Thank you 💯

@DIYwithMichaelBorders

2 жыл бұрын

You are very welcome, thanks for watching.

Great video. I just replaced my pump with a new one but it still won't drain. Definitely installed correctly as was very easy, what else could it be? Not sure any of the other parts are blocked since i was able to shop vac the water right out the end of the drain hose, water seems to flow out just fine

@DIYwithMichaelBorders

2 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. Let’s get this figured out. 😀 Since pump is replaced, you may have a clogged drain hose. A clogged drain hose is usually what ends up causing the pump failure...as it makes the pump take on back-flow/pressure water...which it can’t handle long. Below is a link to a video showing the removal of drain hose and cleaning it. kzread.info/dash/bejne/daatx8Vpk7eZgrg.html Please keep us posted, us DIY’ers need to stick together! 😎👍

Is there another filter in the machine that needs to regularly be cleaned out, from the front of the machine? Great video!

@DIYwithMichaelBorders

3 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. On most machines, there is a Push-to-Open access door on front panel that allows you to clean internal pump filter. Below is a link to a different machine showing this door and filter. kzread.info/dash/bejne/haKqwZSoaN2whbw.html 😎👍🔧🔩

I have an old Maytag Neptune. What’s weird is my unit won’t drain. I tried to drain it by unhooking the end to the drainpipe and putting it in a bucket but nothing. But when I remove it from the drain pump assembly, water gushes out. I cleaned the drain tube and there is no obstruction. I think the drain pump assembly has something going on. I read somewhere that a person had a quarter stuck. Do you have a way to drain this when the tube won’t drain it?

@DIYwithMichaelBorders

Жыл бұрын

Thanks for watching, clogged drain pump is likely and replacing it will do wonders for your machine. Below are a few videos that might be helpful in the process of your project in regards to draining water from system. kzread.info/dash/bejne/Y5hoy8eilNG6erQ.html kzread.info/dash/bejne/daatx8Vpk7eZgrg.html 😎👍

We have an older model but it looks the same. How do i know if it is a clog or failed pump? I screwed the hose and removed from the pipe. Some water drained but i had to shake and move the hose well. It makes a loud noise when draining.... how can i figure out if it is clogged and what can i do??

@DIYwithMichaelBorders

6 жыл бұрын

Laura Leeper Thanks for checking out the video and sharing your comment & experience! Let’s figure this out together! At this point...as you mentioned, your Drain Hose should be cleared of any debris. Quick question...have you recently heard any odd noises coming from the Washing Machine during the draining portion of the cycle? Maybe the sound of clacking or ticking plastic sound...? If yes, that is clear indication of your Drain Pump & it’s inner parts beginning to fail...and sooner or later it will fail all together...leaving you with a washer tub bowl full of water. Since you know how to unhook Drain Hose & empty water out of washer bowl...I would hook everything back up & run a test cycle...if all goes well, then your unclogging hose procedure cured the problem. However if the cycle stops at the Drain portion again & does not drain...then you will need to empty washer bowl again by disconnecting the Drain Hose and then purchasing a new Drain Pump. This is very user friendly. Keep us posted! Please subscribe to the channel and turn on your KZread notifications that would be awesome thanks again 😎👍! Let’s get this washer back up & running 😀🔧🔩 Below is link to Hose Drainage...Definitely Check it out! kzread.info/dash/bejne/daatx8Vpk7eZgrg.html

Is the pump first thing you check when the tub won't spin, drain & make noises? Are there other things I should check as well, if yes which order should they be checked?

@DIYwithMichaelBorders

5 жыл бұрын

T. Charles White Thanks for watching & sharing your comment. Great question. Let’s get this figured out. Are the noises you’re experiencing a grinding sound or grinding & clicking sound? If so, it’s almost always your drain pump. Once your drain pump fails, it will no longer drain nor spin nor continue the wash cycle to the end. No fun 😩 This is a great place to start as it’s a very friendly DIY project & doesn’t drain the bank account. 😎 Keep us posted & let’s get this figured out. Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again. 😎👍🔧🔩

@tcharles8172

5 жыл бұрын

@@DIYwithMichaelBorders It actually make a whinning noise & it drains intermittently. Think it may have debis clogging the ports. I'll definitely start with the pump, thank you for sharing your skills with us and responding to my question specifically!

@DIYwithMichaelBorders

5 жыл бұрын

T. Charles White Thanks for the update. Here’s my thought. You may have a slightly clogged drain hose. This clog may be over working your Drain Pump. Your pump is possibly working extra hard to pass water through the hose. It’s most likely just shy of failing completely. 😲 Below is a link to a video that shows the same washer & what we experienced with a clogged hose. Definitely check it out. It’s probably time to replace Drain Pump & clean hose. Keep us posted! 😎👍🔧🔩 kzread.info/dash/bejne/daatx8Vpk7eZgrg.html

Where did you get the new pump from and what was the cost? TIA

@DIYwithMichaelBorders

5 жыл бұрын

Ricky Howard Thanks for watching Ricky. We definitely recommend checking a few different places to get the best deal. We recommend checking: • Amazon • Repairclinic.com • Ebay We have had great luck with Repairclinic.com Enter your model # in the search & parts will be provided. Keep us posted on your project. Let us know if you have any additional questions along the way we are here to help! Please subscribe to the channel and turn on your KZread notification Bell that would be awesome thanks again! 😎👍🔧🔩

Mike, i have insufficient voltage to the pump 24-54vac when the pump should be getting 110vac. what is a valid PN for the output board/control. - thank you griffin in michigan

Maytag neptune front loader. My pump works but tub won't drain all the way. I hear lots of water slosh in the background. I took the intake hose off the pump, the fat one, then took the hose off the tub, and nothing is draining. Water is sloshing in the tub. What keeps the water in the back there?

@DIYwithMichaelBorders

5 жыл бұрын

scott boelke Thanks for watching & sharing your experience. Let’s get this figured out! The most common cause to your experience is a lack of draining capabilities. It’s very possible that your Drain Pump is beginning to wear out & work intermittently. We recommend purchasing a new Drain Pump & replacing it. This is a very friendly DIY project as you can see & should resolve your degraded draining issue. Let’s start there! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

@paulpoco22

4 жыл бұрын

Also when it does drain and it is really noisy then the pump is going.

Hey Mike, i have commercial/front loader Maytag Neptune washer. The area got flooded and now the washer requests to continually reselect the cycle, doesnt appear to fill fully but will agitate. I changed out the water pump and now it will go to completion but doesnt spin enough to drain all the water and i dont think it fills fully. Any suggestions??? (i've also changed the circuit board but issue still occurs)

@DIYwithMichaelBorders

2 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. We recommend performing a full system reset. Below are two links to helpful reset videos. kzread.info/dash/bejne/om2G2dKDaMfcp5s.html kzread.info/dash/bejne/Z3aZppKMeKzaZbQ.html 😎👍🔧🔩

How do you know that the pump is bad n not just clogged?

@DIYwithMichaelBorders

5 ай бұрын

Good morning ☕️ In most cases, you will get an error code on your panel that coincides with pump failure. However, once you remove panel and gain access to the pump, you can unplug the electrical connections and check the continuity with a voltmeter to ensure whether or not the pump is faulty or still good. Let us know if you have any additional questions. Looking forward to 2024, many more helpful videos to come! ☕️🧰

Hi guy i have the question, coudl you help me ? maytag neptune mah6700aww timer freezes after finis washing, is de water pump? thanks

@DIYwithMichaelBorders

4 жыл бұрын

Inversiones Hexasystem Thanks for watching, what’s your update? Have you got your machine back up & running? Is your machine setting off any error codes? Let’s get this figured out! Keep us posted. Please subscribe to the channel and Ring your KZread Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

hello I hope you are very well I have a question where can I order that pump

Love your video. But my washer doesnt drain like that because its not on a pedestal. Not sure how to get the water out.

@DIYwithMichaelBorders

2 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. Let’s get this figured out. Below is a link to our video showing a drain feature. kzread.info/dash/bejne/gHiDqbitnLiqo9Y.html Keep us posted. 😎👍🔧🔩

So I got an Hr error code on my Maytag Neptune mah8700awm and assume it was related to this issue as water was not draining. Though when I remove the tube from the water pump tons of water is spewing about. Any ideas?

@DIYwithMichaelBorders

2 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. This is due to excessive suds. Below is a link to our video showing how to address this on our Samsung machine. kzread.info/dash/bejne/haKqwZSoaN2whbw.html 😎👍🔧🔩

Great video. ... But I'm stuck.. I don't see on my left two bolts.. What now ????

@DIYwithMichaelBorders

5 жыл бұрын

Sonya S Thanks for watching, what’s your update? Have you been able to remove old part yet? Keep us posted, we are here to help! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

@sharonalexander1694

3 жыл бұрын

Well mines didn't have the bolts either. It had 5 screws to unscrew with a Phillips head, pops right out.

I'm having a problem with the screws that hold the bracket on the machine ?I can't get them out they just keep turning why and what do I do. I got one removed the other two keep turning?

@DIYwithMichaelBorders

Жыл бұрын

Thanks for watching Pamela, try adding some friendly upward pressure to screw with your fingers as you simultaneously unscrew it. If that doesn’t work, try applying some friendly sideways pressure to screw as you simultaneously unscrew it. Please keep us posted.

Hose cleared, replaced pump and still not draining. What can I try next?

@DIYwithMichaelBorders

4 жыл бұрын

Carly Chow Thanks for watching. That’s a bummer. Depending on your machine, you may have a drain filter. Have you verified the Drain Pump Filter is cleared? Many more helpful videos to come! 😀 Please subscribe to the channel and Ring your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

HI GOOD DAY MY WASHER IS SHOMING A CODE E2 DO YOU KNOW WHAT THAT MEANS

@DIYwithMichaelBorders

Жыл бұрын

Thanks for watching, the Maytag E2 fault code indicates a slow-flow of water through drain hose or a total blockage. Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem. toolboxtoken.com Reach out to us any time! 🧰

Question. I hear water in our washer. When I take the drain hose out of the wall where it drains to nothing comes out, does this mean it’s plugged? Thank you

@DIYwithMichaelBorders

5 жыл бұрын

Mara P.Avila Thanks for watching & sharing your experience Mara. What is the current state of the wash cycle? It it washing & fully completing cycle or is it stoping mid cycle & not draining? A clogged drain hose will definitely cause the cycle to stop. Below is a link that shows & explains it a little better, definitely check it out! kzread.info/dash/bejne/daatx8Vpk7eZgrg.html Let’s start there, keep us posted! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

@MaraPAvila

5 жыл бұрын

It is washing and completing cycle.

@DIYwithMichaelBorders

5 жыл бұрын

Mara P.Avila Thanks for the update. That’s good news! We recommend monitoring the drainage & verifying the drain pump is pumping water out the drain hose. There is always going to be a small portion of water remaining in your Washing Machine after wash cycle is complete, that’s normal. Keep us posted! 😎👍🔧🔩

@MaraPAvila

5 жыл бұрын

Oh 😯, I didn’t think it was normal. When I wash clothes and dry it, the clothes always has a smell to it, i thought maybe it could be because of the water that’s always there. Thank you for your quick response.

@DIYwithMichaelBorders

5 жыл бұрын

Mara P.Avila The water level will always be below the bowl & never seen. The smell is most likely coming from build up. We recommend doing a thorough cleaning of the machine to get rid of smell. 😎👍🔧🔩

I get a C-12 critical error. Anyone know what that is?

@DIYwithMichaelBorders

Жыл бұрын

Thanks for watching, any update? We haven’t seen the c12 fault code yet and oddly enough…Maytag fault code master diagram doesn’t show it…🤔

Hi Michael, I have the same model MAH6700AWW. it had a ND code, after I watch your video I removed the pump and found nothing on it, no kink on hoses and restart a wash cycle it got stuck at the end of wash cycle before it goes in the spin cycle. I then bought a new drain pump but the problem still there. I heard the clicking sounds from the control board like it is trying to do something. What else should I try? I ordered a water sensor switch and it is on the way. Thanks in advance.

@DIYwithMichaelBorders

5 жыл бұрын

Minh Pham Thanks for watching & sharing your experience. Let’s get this figured out! The ND code is triggered when the water level does not drop below the low level reset. This is usually caused by a faulty / failing pressure switch. We recommend blowing through the pressure switch hose & see if that resets it. If not, we will move toward replacing the actual Switch itself. Let’s start there! Keep us posted! Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

@brunomaltaferreira

5 жыл бұрын

I have this same variant of the problem. Replaced the pump but it does not spin/drain. Always there’s a significant policing of water in the drum together with the clothes. You recommend blowing into the hose?

What if you swap out the pump and it still won't drain?

@DIYwithMichaelBorders

Жыл бұрын

Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community. Great question, it’s very likely that the hose is clogged. Since it’s a brand new pump, it’s trying to drain however will immediately turn off when it detects a back flow…which is sensed when there’s a clog in hose. Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem. toolboxtoken.com Reach out to us any time! 🧰

@bryanf38

Жыл бұрын

​@@DIYwithMichaelBorders Thank you for the response. I pulled the hose and rinsed it. It wasn't really that dirty. Definitely not clogged

@DIYwithMichaelBorders

Жыл бұрын

@@bryanf38 Thanks for the update, that’s better than a clogged hose. A clean and clear hose is a great thing!

It would have been nice to include the diagnostic steps that distinguish between a broken drain pump and a clog that could be fixed by removing the obstruction. For instance, does a clogged drain make a very different sound than a broken pump (when the washer is trying to drain the water from the drum)? If the water remaining in the drum's outer shell won't syphon out through the drain hose when the end of the hose is placed near the floor, or syphons at a low flow rate, does that imply a clog? I have two old washer-dryer stacks: (1) The Maytag MHS2000AWW makes a noise when I think it's supposed be draining, and perhaps that noise means the pump is working okay, and no water drained out when I put the end of the drain hose near the floor, so perhaps these clues suggest a clog instead of a broken pump? (2) The Frigidaire Gallery FWT445GES2 only makes a humming/buzzing sound when I think it's supposed to be draining, which reminds me of the sound a jammed garbage disposer makes, and the water syphoned out very slowly, so perhaps these clues suggest the pump is jammed by an obstruction that's also limiting the drain flow?

How do you know for sure it's the drain pump needing replaced? Was there an error code?

@DIYwithMichaelBorders

2 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. The P5 error code usually is triggered when you have low water supply to unit. You may need to clean screens inside water lines that connect directly to the washer. Video link below talks more about this. kzread.info/dash/bejne/dqt-rsZwqNrHhbA.html 😎👍

@yukuhana

2 жыл бұрын

@@DIYwithMichaelBorders Thanks. I don't think I remember the code correctly, may have been PF. BTW, at 5:07, is that pump clogged?! Could removing the clog fix the drain problem?

@DIYwithMichaelBorders

2 жыл бұрын

@@yukuhana You are very welcome, it may also be a clogged drain hose. Below is a link to our video showing the removal of hose to clean it out. kzread.info/dash/bejne/Y5hoy8eilNG6erQ.html Let’s get this figured out. 😎👍

@yukuhana

2 жыл бұрын

@@DIYwithMichaelBorders I removed the hoses around the pump but no debris. So I guess next step is to buy the drain pump. What's your part number? I searched up Maytag Neptune MAH6700aww, and it came up with DC96-00774A. It seems some websites include brackets, while other only include the motor unit without the drain hose connectors. Do you have an opinion on that? Where can I get the part fast?

@DIYwithMichaelBorders

2 жыл бұрын

@@yukuhana Thanks for the reply, we came up with an OEM part # of WP34001340. That’s referencing your machine serial # you provided. If interested in purchasing this part, visit our Amazon affiliate link below. I earn from qualifying purchases. amzn.to/3HlrNDT 😎👍🔧🔩

Amana front load washing machine NFW7300WW02 will not start get three beeps will ot start up

@DIYwithMichaelBorders

4 жыл бұрын

Robert Morris Thanks for watching & we hope the video helped. By chance has your machine illuminated any error codes? We really enjoy making these helpful videos for our fellow DIY’ers. Many more helpful videos to come! 😀 Let us know if you have any questions. Please subscribe to the channel and turn on your KZread notification Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

Hi. I have an ND message I research it may be the pump. I bought the new pump but still not working

@DIYwithMichaelBorders

3 жыл бұрын

John Hoang Thanks for watching & that’s no fun. Have you verified your drain hose is clean and clear. Below is a link to our video showing us cleaning our drain hose. Hope this helps. kzread.info/dash/bejne/daatx8Vpk7eZgrg.html Keep us posted. 😎👍🔧🔩

What model is this Maytag??

@DIYwithMichaelBorders

3 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. This is the Neptune. Let us know if you have any questions. 😎👍🔧🔩

Supplier for pumps? Amazon, eBay ?

@DIYwithMichaelBorders

6 жыл бұрын

Terry Polk Thanks for watching Terry. We definitely recommend checking a few different places to get the best deal. We recommend checking: • Amazon • Repairclinic.com • Ebay We have had great luck with Repairclinic.com Enter your model # in the search & parts will be provided. Keep us posted on your project. Let us know if you have any additional questions along the way we are here to help! Please subscribe to the channel and turn on your KZread notification Bell that would be awesome thanks again Terry! 😎👍🔧🔩

so i disconnected the hose from the wall and put it in my bucket but the water from inside the washer is not coming out

@uhhdanielle8829

4 жыл бұрын

also it is making a noise as if something is loose

@uhhdanielle8829

4 жыл бұрын

okay got the water drained and then put everything back together and hearing a rattling noise, what needs to be replaced?

@DIYwithMichaelBorders

4 жыл бұрын

Uhh Danielle Thanks for watching. We appreciate you sharing. Does your washer complete a full cycle from start to finish now? Can you pinpoint where exactly the rattle is coming from...? Keep us posted! 😎👍🔧🔩

@uhhdanielle8829

4 жыл бұрын

DIY With Michael Borders i took the pump apart and the little white propeller was loose. i snapped it back on and put everything back. it finally completed a test load i did with no clothes, and there was no water leftover in the tub, but it still rattled a bit. i can’t pinpoint exactly that the rattle is coming from the pump tho or even what part of the pump. i’m going to order a new pump and replace it. hopefully that fixes the issue.

@DIYwithMichaelBorders

4 жыл бұрын

Uhh Danielle Thanks for the update. Has the new part arrived yet. We are interested in hearing if the new pump alleviates the rattling sounds. 😎👍🔧🔩

Great video just got a question, how did you know for sure it was the drain pump assembly? Just wondering cause mine just stopped draining and I'm thinking it's the pump since I took it off and nothing was clogging it but want to be sure this is the problem since I'm not a washer repairman. Lol Thank you in advance

@paulpoco22

4 жыл бұрын

If you do replace the pump, you can then take apart the old pump to see if the impeller and shaft are loose or missing parts of the fins that turn to pump the water.

We replaced with new and still won't drain stops in middle cycle when it goes to rinse cycle..

@DIYwithMichaelBorders

4 жыл бұрын

Charity Burton Thanks for watching, have you also verified that your drain hose is clean & clear? Below is a link to our step-by-step video that shows how to check. kzread.info/dash/bejne/Y5hoy8eilNG6erQ.html Keep us posted! Please subscribe to the channel and Ring your KZread Bell 🛎 that would be awesome thanks again! 😎👍🔧🔩

@charityburton954

4 жыл бұрын

@@DIYwithMichaelBorders so it is all clean it wont even do just spin and rinse. Could it be the cold water valve?

@charityburton954

4 жыл бұрын

@@DIYwithMichaelBorders or are there other filters somewhere?

@DIYwithMichaelBorders

4 жыл бұрын

Charity Burton You may need to also verify that the rubber hose feeding out of bottom of tub & into pump is clean & clear. Next, verify that your door lock mechanism is making the clicking sound within a few seconds after starting your cycle. A faulty door locking mechanism can cause the cycle to stop. Keep us posted. 😎👍🔧🔩

@charityburton954

4 жыл бұрын

@@DIYwithMichaelBorders bought a new one of those and still not working

Where can I order or Purchase this Drain Pump?

@DIYwithMichaelBorders

3 жыл бұрын

Thanks for watching & welcome to the DIY Raptor Club. We purchase all our parts from: RepairClinic.com Enter in your units model # & all available replacement parts will be provided. Keep us posted on your project. Us fellow DIY’ers need to stick together! 😎👍🔧🔩

@karlhector3584

3 жыл бұрын

@@DIYwithMichaelBorders No Thank You

@DIYwithMichaelBorders

3 жыл бұрын

@@karlhector3584 😎👍🔧🔩

@karlhector3584

3 жыл бұрын

@@DIYwithMichaelBorders I replaced the Pump but I am still getting error message ND. Any suggestions

@DIYwithMichaelBorders

3 жыл бұрын

@@karlhector3584 Thanks for the update Karl, is your machine completing a full cycle now & the code is being displayed?...if yes, you can unplug the machine and leave it unplugged for 30 minutes. This will allow your system to perform a full reset. If that does not work, you may have something slightly clogging your drain hose. Below is the link to our video showing removal of hose. kzread.info/dash/bejne/Y5hoy8eilNG6erQ.html Keep us posted. 😎👍🔧🔩

Mine had a coin stuck in it, bought a pump for nothing.

@DIYwithMichaelBorders

2 ай бұрын

Thanks for watching, hey nothing wrong with a brand new pump. 😁👍 Awesome job making it a DIY project, you will continue to benefit greatly by making your projects DIY. 🧰

Bad news to report: 1) check for debris : None found, still won't drain. 2) replaced the drain pump : Still won't drain. What's the next thing I can try? It appears to be electronic problem (e.g. control board doesn't actuate pump); if that's the case, I'd be out of luck. $130 just for repairman to come and estimate required labor + parts. Feeling defeated. I might have to buy a new washer...

@DIYwithMichaelBorders

2 жыл бұрын

Thanks for the update, that’s no fun. Have you tried performing a full system reset? Below are two links to reset procedure videos. kzread.info/dash/bejne/Z3aZppKMeKzaZbQ.html kzread.info/dash/bejne/om2G2dKDaMfcp5s.html In these videos, we reference a Samsung unit however the concept is the same with your Maytag. Please keep us posted. 😎👍

@yukuhana

2 жыл бұрын

​@@DIYwithMichaelBorders Actually that's the first thing I did. So I tested the voltage at the drain pump by going into "service mode" and executed a "Board Output Test" for drain pump, and it did successfully apply the 120 voltage at the drain pump!! However, going through the spin cycle program (water emptied manually), I didn't see the 120 volt at the drain pump even as the washer spun. So whatever the "trigger" is isn't working, even though the control board is capable of delivering voltage at the pump. I don't think there's anything else I can do.

@DIYwithMichaelBorders

2 жыл бұрын

@@yukuhana Thanks for the reply, since you have checked voltage, verified drain hose is clean, and replaced drain pump... The only thing it can be from here is a faulty electrical part or wire/wire connection point.

@yukuhana

2 жыл бұрын

@@DIYwithMichaelBorders Thus it's out of my hand. I've just placed an order for a new washer. Unfortunate ending :(

@DIYwithMichaelBorders

2 жыл бұрын

@@yukuhana Hopefully many stress free days ahead for you with that new washer. 😎👍

How much for the pump

@DIYwithMichaelBorders

3 жыл бұрын

Thanks for watching & on average, a pump ranges between $70-150 depending on how fancy the machine. 😎👍🔧🔩

@nukenridge4921

3 жыл бұрын

@@DIYwithMichaelBorders maytag 2000 the propeller moves forwards 1/16 only .I reset it once unplugged for 5 minutes. And all works so far ,my guess is if it does not wobble and but moves forwards 1/16 means it the pump is almost due

@DIYwithMichaelBorders

3 жыл бұрын

@@nukenridge4921 Awesome Awesome & we appreciate you sharing this. Hopefully many stress free days ahead for you. 😎👍🔧🔩

Omg too much detail..

@DIYwithMichaelBorders

3 жыл бұрын

Thanks for watching & we appreciate your thoughts. Enjoy your day. 😎👍🔧🔩