Replacing the pump in a Maytag Neptune Washing Machine
Жүктеу.....
Пікірлер: 28
@Brad5161 Жыл бұрын
Excellent video! Had a large ceramic piece lodged in the impeller area but the impeller was undamaged. Cleared it, cleaned it and it seems to be fine. The unit would twist off so I removed the whole assembly which was very easy. Have to clean up the water now. Thanks.
@MrBest7972 жыл бұрын
BEAUTIFUL!
@fredrauh663 жыл бұрын
Mine has a set screw in the base of the isolator that keeps the pump from spinning. You have to take the whole thing out first and remove the screw before it will spin loose
@jamesmuir52296 ай бұрын
I have water at the inlets but the washer isn’t getting water
@sprtplt Жыл бұрын
Where's the filter and how do you clean it?? Would be kind good to show that!
@Jimmothy4202 жыл бұрын
DRAIN PUMP DB-02 120v 60hz 85w 45L/Min
@NINO-gv9ds3 жыл бұрын
Thx for the video, where was nickel stuck? What if it drains but doesnt spin? Would i have i still have to change the drain pump? Thx again
@aaronsrose
3 жыл бұрын
Howdy! I don't recall exactly where the nickel was. If yours is draining ok, but not spinning, if say the pump is pumping and there may be something else holding out the spin cycle. Thanks!
@fiodortodiras25473 жыл бұрын
Mr. Rose I did change the pump but something went wrong with the installation, then I did instal again and did not work anymore
@fernandogonzalez64182 жыл бұрын
Explanation done very well on how to se it up; were did you find the motor for that price?
@aaronsrose
2 жыл бұрын
Howdy! It's been awhile but I usually find the correct part on repairclinic.com and then try to find it cheaper on Amazon or wherever I can. Thanks!
@paulpoco224 жыл бұрын
Was there a Filter? Or did you take the rubber piece that goes to drum and clean that out?
@aaronsrose
4 жыл бұрын
Iirc, there was no filter as such. I think there was a screen built into one of the pump couplers. Thanks!
@wall2wallsportsrehab44711 ай бұрын
I need to replace my pump. Looks like it’s the same model number. Any recommendations as to wear to buy a good replacement pump?
@aaronsrose
11 ай бұрын
Howdy! I usually find the parts on Repairclinic.com. There may be some alternatives out there but you should at least be able to get a correct part number from them. Thanks!
@713lopezf3 жыл бұрын
Did washer give you any codes when it started to act up? I have the same washer model and started give me the ND code.
@aaronsrose
3 жыл бұрын
Howdy! It's been awhile but I don't recall any codes prior to their failure. Thanks!
@713lopezf
3 жыл бұрын
@@aaronsrose Thank you for quick response. Washer is giving the ND code for Not Draining. I cleaned the water tube out - no clogs! I removed the drain pump/motor but not sure what to look for to see if damaged. Should i just go forth and replace to see if it's the issue?
@aaronsrose
3 жыл бұрын
I'd say that if everything looks clean, is try the pump replacement it it were mine.
@lalocster7885 жыл бұрын
hello where dis you get that prt and what was the cost? can u please provide the link thanknu
@ecoguate
4 жыл бұрын
Hello, I have the same question. Can you please let me know where did you buy the part. Thank you
@zinaistefan2165
4 жыл бұрын
@@ecoguate i found it on ebay
@ecoguate
4 жыл бұрын
@@zinaistefan2165 thank you.
@chouxiong159210 ай бұрын
How can I unlock the door?
@aaronsrose
10 ай бұрын
That is a good question. I would expect that it should unlock if the power cord is unplugged. If that does not work, there may be something stuck in the latch. Possibly a thin shim might be able to wiggle behind the latch and free it.
@chouxiong1592
10 ай бұрын
@@aaronsrose I got the door open by unplugging the wire, open the top, stick my hand down to the lock and push it out. But now my washer won’t open when I plug up the wire, and it won’t spin or drain. Makes light buzz sound. Not sure what’s going on.
Пікірлер: 28
Excellent video! Had a large ceramic piece lodged in the impeller area but the impeller was undamaged. Cleared it, cleaned it and it seems to be fine. The unit would twist off so I removed the whole assembly which was very easy. Have to clean up the water now. Thanks.
BEAUTIFUL!
Mine has a set screw in the base of the isolator that keeps the pump from spinning. You have to take the whole thing out first and remove the screw before it will spin loose
I have water at the inlets but the washer isn’t getting water
Where's the filter and how do you clean it?? Would be kind good to show that!
DRAIN PUMP DB-02 120v 60hz 85w 45L/Min
Thx for the video, where was nickel stuck? What if it drains but doesnt spin? Would i have i still have to change the drain pump? Thx again
@aaronsrose
3 жыл бұрын
Howdy! I don't recall exactly where the nickel was. If yours is draining ok, but not spinning, if say the pump is pumping and there may be something else holding out the spin cycle. Thanks!
Mr. Rose I did change the pump but something went wrong with the installation, then I did instal again and did not work anymore
Explanation done very well on how to se it up; were did you find the motor for that price?
@aaronsrose
2 жыл бұрын
Howdy! It's been awhile but I usually find the correct part on repairclinic.com and then try to find it cheaper on Amazon or wherever I can. Thanks!
Was there a Filter? Or did you take the rubber piece that goes to drum and clean that out?
@aaronsrose
4 жыл бұрын
Iirc, there was no filter as such. I think there was a screen built into one of the pump couplers. Thanks!
I need to replace my pump. Looks like it’s the same model number. Any recommendations as to wear to buy a good replacement pump?
@aaronsrose
11 ай бұрын
Howdy! I usually find the parts on Repairclinic.com. There may be some alternatives out there but you should at least be able to get a correct part number from them. Thanks!
Did washer give you any codes when it started to act up? I have the same washer model and started give me the ND code.
@aaronsrose
3 жыл бұрын
Howdy! It's been awhile but I don't recall any codes prior to their failure. Thanks!
@713lopezf
3 жыл бұрын
@@aaronsrose Thank you for quick response. Washer is giving the ND code for Not Draining. I cleaned the water tube out - no clogs! I removed the drain pump/motor but not sure what to look for to see if damaged. Should i just go forth and replace to see if it's the issue?
@aaronsrose
3 жыл бұрын
I'd say that if everything looks clean, is try the pump replacement it it were mine.
hello where dis you get that prt and what was the cost? can u please provide the link thanknu
@ecoguate
4 жыл бұрын
Hello, I have the same question. Can you please let me know where did you buy the part. Thank you
@zinaistefan2165
4 жыл бұрын
@@ecoguate i found it on ebay
@ecoguate
4 жыл бұрын
@@zinaistefan2165 thank you.
How can I unlock the door?
@aaronsrose
10 ай бұрын
That is a good question. I would expect that it should unlock if the power cord is unplugged. If that does not work, there may be something stuck in the latch. Possibly a thin shim might be able to wiggle behind the latch and free it.
@chouxiong1592
10 ай бұрын
@@aaronsrose I got the door open by unplugging the wire, open the top, stick my hand down to the lock and push it out. But now my washer won’t open when I plug up the wire, and it won’t spin or drain. Makes light buzz sound. Not sure what’s going on.
Part number??
That was built by Samsung throw that junk away