Really helpful! You don't have to buy duplicator. This jig is working! And you did a great job! Nice!

Thanks for sharing and the tips. I was planning a credenza with round legs. Now I know how I’ll make those round legs 👍

my friend . very nice. thank you so much.. be happy.. bravo

This is one worth building. Thank you.

Love watching you work , you are a true professional

This is the easiest method I have seen for making dowels! Nice work!

Funny how people vary. I like making jigs and tools more than finished products! Great video!

it is a good thing to let people see that things can go wrong. And how to deal with it. great job . blessings from Belgium..

Awesome! Thanks for sharing the experiment!!

Very cool! It’s fun thinking through the process.

About 12 years old, I asked my farmer Dad what it takes to be a good woodworker. He said, "I haven't done it, so I can only observe. What I think it takes is getting good at making small pieces of wood out of large pieces of wood."

@johannesisager5634

4 жыл бұрын

I think its opposite tho. When you can make big pieces of wood out of small ones, your doing pretty good

@grumblycurmudgeon

3 жыл бұрын

Isn't that the quintessential approach to carving an elephant? You start with a block of marble (or as the case may be, whatever flavor of hardwood you prefer), and remove all the parts that aren't an elephant? In my opinion, there are three things that make an amazing woodworker (which, incidentally, are the same things required to be a fine artist, a painter, a sculpter, etc. and an engineer): 1. The ability to set something up with precision, be it cutting a straight line, or milling a certain thickness, or a carving a curve: one must prepare the stock and the tools alike and ensure they are as close to tolerance as it's feasible to achieve with the materials they have to hand. For the important parts of the piece, milling, cutting, sanding, finishing, whatever: if your setup took less time than the execution? You wanna really look at that process (assuming you're not batching out 100 of something, of course). 2. Patience. The HARDEST part of any of those skills listed is simply not rushing or taking shortcuts. It's easy to cut a piece of wood. It's HARD to cut 300 exactly the same. Often times we'll change feed rate, get a bit over-ambitious with a router plunge etc. just because we're NOT robots and feeding 2400 linear board feet through a saw it as tedious as it is nerve-wracking. 3. Willingness to fail. You will screw up. A lot. More often than not, you're the ONLY ONE who'll ever see said screw-up in the final piece. But you'll know. Beyond that, though, ever have to make a tricky cut or route a complex profile or shape into a piece you've already got 50+ hours in? Or in a piece of wood that costs more than your table saw? Ever screw THAT up? It's terrifying doing what we do sometimes. Sucking it up and doing it anyway is the only way through, but it never gets easier. I failed to notice the grain switch back on itself once while doing a simple roundover... on an $1100 spalted Roman Olive slab. Bit caught and ripped a 5" GOUGE (that can never be filled or color-matched due to the spalting) in one of the final, pre-finishing steps of a piece. I've had long-term relationship breakups that made me cry less. And the terror never goes away, never gets easier. But what else can you do? S'not like we're gonna quit working wood, amiright? Set up right. Go slow. Be brave. Manage those three and you got this.

Thanks for sharing that, well said and done!

Nicely done clean workmanship

Super smart and elegant solution. Nice work!

I love this tool. Repeat, repeat.

Take a block of wood that just fits inside your jig and add a center pin to it. After that just put in any length of block to take up space behind it and use the drive side to set the tension, you can now make different length dowels.

Great jig! Two thumbs up. Nice design, far superior to most I've seen on KZread so far. Also very safe and easy to precisely adjust the size of the dowel. This is a great example of the fundamental KISS principle that always works best (Keep It Simple, Stupid)!

@papaike2

5 жыл бұрын

The KISS moto I've used it my entire life and it's never let me down.

Enjoyed the video and the explanations along the way. Good job!

Add 3 wooden gears on the drive end. The center gear in line with the dowel and the other two centered on the outside edge of the top corners. Make the outer gears turn some all-thread rod, and attach nuts to your router sled. This way, you can turn the drive end with a drill set to slow and the router will move along the track in one smooth motion as the dowel turns. Easy peasy auto-dowel maker. :D

Great video! Great jig! Many thanks!

I think you done very well with this project. It takes trial and era to become a good wood worker when you’re mostly learning on your own and getting advice from some others who’s walked the path learning. Hey dude, I’m 65 and I still learn something new with new projects and even older things I’ve learned to build. By the time I was 18 I was able to design and build my own home workshop and most everything else wood. Most of my furniture I made. I wish I could have had your setup when I was first starting out. You did a great job and learned a few things in the process. Like using a smaller washer to put as stops on the ends of your beginning dowels. Bits are very expensive as you’ve learned. Adding a small electric motor with a fast rpm will help you use both hands and it will make your dowels a lot smoother when finished. On some hardwoods I don’t even have to sand anything really but I do for the look and especially it what I’m building is being given as a gift or sold. Keep it up young man.

I have made a jig like this, but I powered mine with a garage door opener motor. The chain and drive sprockets also come from the same unit. Means you have two hands on the router and in full control. Very easy to do! I have used this power source for many things. I get them from installers who have replaced with a new unit and would have other wise be dumped.

You have some good ideas that I can use, I like building my own tools. Thanks for sharing.

Love the idea...I'm making one. I'll try to add dust collection. Thanks for the video

@parillaworks

5 жыл бұрын

Thanks. Yup, I need to add some DC too.

Nice idea & jig. Based on the comments, I think that you will be able to fine tune it & get exactly what you want. Great job thus far...............

enjoyed the video - thanks for sharing.

Great jig, great video. 👍 Thanks for taking the time to record, edit, produce and upload. Enough to make me subscribe 👍

Really nice demonstration of a useful jig. Thanks for posting. 💯

This is brilliant. Add an adjustable stop for the router to prevent you hitting the nut again. Maybe also dust collection somehow?

That's really interesting - I didn't realise it was driven. I'm about to make some quarter rounds for a kitchen island. I might glue them together and do all 4 at once like this.

My suggestion is that you setup a foot pedal to control the drill, that way you can concentrate on the router movement. Great video

Great video, I am very glad I found this channel last year. This is great content and I liked hearing about your thoughts on bit selection the most. Thanks again!

@andrzejbajorek768

5 жыл бұрын

.

Thanks to the Master! - Like from AZE 🇦🇿

Well done Sir!!!

What a nice idea Genius

Great troubleshooting and experimenting! Thanks for taking us on the ride, looks like a good addition to the shop without breaking the bank. Generic comment about Dust Collection ;)

@parillaworks

5 жыл бұрын

Thanks Tharemy! The DC comment can be made about all of my videos, if I'm honest!

Great info. Very detailed/

That’s a great idea.

Bravo, you are one of my favorite channels, Excellent designs and execution

@parillaworks

5 жыл бұрын

Thank you!

Interesting concept.

Great Job!

Very good and easy thanks 🙏

Great work.

Молодец ! Такую приспособу я сделал к токарному станку по-дереву ,правда из металла . Сейчас перевожу эту приспособу к 2D принтеру ,через CNC ардуинку с компа ... Как раз завтра буду красить этот станочек и покрою даже лаком ... ;))) Так что успехов тебе ....

Awesome!

Es el torno mas ingenioso que e visto y con materiales simples y economicos de conseguir, muy bueno tu desarrollo y trabajo...

I like more this jig than the table saw that I found dangerous. Besides this one probably can allows sort of a woodturning. Great job.

Good idea.

Consider mounting the drive (drill motor) so you have both hands free...and a foot switch fr similar similar method to turn it on. Beyond that, an excellent video, very clear and descriptive. Izzy Swan has a video(s) on this also; he takes another approach though. Thanks for the clear video and "WELL DONE".

You are a nice guy. Good work, i will try to make the same jig.

You should mount (strap, U-bolt) the drill on a platform along side the drive end of the jig to free your hands for better control, plunge and lateral movement of the router. To keep the drill on include a trigger control.

bravo

Nice making

Very cool

Excellent video. I would look for a used sewing machine motor to drive the dowel, then you can set the speed and also use both hands on the router. But well done!👍

Some suggestions? Mount the tail stock screws in a sliding box that allows overall length adjustment (slots in the side with dove tail runners). Add a dust collector hole near the bottom. Add a foot switch to turn the router (mounted on a stand added to that end) on and off allowing you to use both hands if needed.

@parillaworks

5 жыл бұрын

Thanks Clyde, I always look forward to your comments. I really like the sliding tailstock idea.

@jimyoung7090

5 жыл бұрын

I checked the comments to see if anyone had already suggested a sliding tail stock. Glad it's already done. Jim Y

For an adjustable tail stock perhaps place rebates at intervals along the long sides and make the tail stock on a single piece of wood you just slide down into those rebates. If you have a concern about the tail stock coming out during an operation. Just make a small steel pin locking device similar to a boxer engine crankshaft turn one way the locking pins go into the side walls, the other way they both come out.

Nice video Thanks for sharing.👍😎JP

pretty good work.

Nice video and a cleaver solution

Really nice! If you made the box deeper, you could add an angled bottom to the box and a vacuum outtake, which would add dust extraction to the jig.

Great video

Hello Sir, nice demonstration of how to make a nice large dowel. If you adjust the height of one end’s spindle, you can then turn tapered shapes and end up with something that is conical rather than cylindrical. That may be useful for say tapered table legs. Cheers.

@parillaworks

4 жыл бұрын

Thanks Peter!

Nice idea for who doenst has lathe machine

One tip that might be useful to reduce tearout: get a tube large enough to hold your stock piece. Put your stock in the tube and then fill the tube with mineral oil. Let it sit for few days-a week to let the mineral oil soak into the wood. Remove the wood and make your cuts on your jig to turn it into a dowel The idea comes from Kings Fine woodworking in a video they did on how to make wooden screws without tearout.

Back in the ‘80s, I bought a “Woodchuck” tool that has a horizontal feed for a router which allowed me to make dowels. I am sure the company is now out of business, long ago.

Yes, you can drill it after the process, use a piece of angle iron as v block, you can center the hole using a drill press. And, if you look back in the footage, the wooden base of the router do have a small gap with the runway, it will cause the router to shake and off center. Fill that gap with a piece of metal, such as beer can and you will be a happy man.

Thank's a lot for sharing. Its easier get a 90 degrees anule if you drill The holes while the blank is square

Thank you so much

Grt. .....crative use of router. .....

I like building my own tools this is Great im going to fix it

Now make a tapering attachment to go on top of this wonderful device you made.

Good capital good job

Muito bom seu vídeo

You should use the sticky tape on your drill and take off the battery as a switch. I personally use that method and I think it's safer since you can focus on the router :). Nice videos. Thanks for upload

@parillaworks

5 жыл бұрын

Thanks. That's a good idea. I might hook up a corded drill. I just need to find a way to mount it securely.

I own a book called "Router Magic" that has plans for a router lathe that I built many years ago (15+?). All the gears, chains bearings, fasteners, mdf & hardboard took weeks to track down & cost around $300. I was obsessed with the challenge. The simplest thing this could do was cut precision dowels. All the way up to the fanciest spiralled chair legs, table legs, bed posts, spiralled & pineappled post tops in any configuration you can imagine. The only limitation in design is your imagination. If you want a really satisfying challenge on an incredibly useful shop made machine. There you go.👽👽👽

@madmaxofspokane1691

5 жыл бұрын

Just checked! They actually have it on Amazon! Written 23 years ago. Router Magic

@parillaworks

5 жыл бұрын

Hi Willy, thank you for sharing! That sounds like a fun build.

Отличная идея спасибо за видио

Since your bit is flat across the cutting face, take the guesswork out of measuring the dowels and get more precise results. Measure from the center of the hole where the drive is to the top of the jig. Then make graduation marks from the top to the bottom for thickness of the dowel, offsetting by what you will need for sanding/error. Then just use the top of the jig as your zero reference and you can now make repeatable cuts without first making a dowel.

👍 очень полезная приспособа.Красава👍

Nice,.

Awesome jig. Love it. Only suggest using push sticks around 0:15 hand too close to blade!

Dude to keep bad mouthing your idea. But i think its awesome. I needed an idea just like this one. Now I'm wicked excited to try it.

@parillaworks

5 жыл бұрын

Thank you! Good luck with it. I need to do some more experimenting with the speed of the bit and the spindle; hopefully I can get a smoother finish. Also, the other day I built the second tailstock. It slides anywhere in the jig and can be clamped into place which makes it very adjustable.

You're kind of a perfectionist aren't you? Well that's nothing to complain about, very nice project, thanks for putting this video up. I'd like to see you make an attachment that could make some of those dowels into threaded wooden screws.

@parillaworks

5 жыл бұрын

In some things, yes. A threading attachment would be pretty interesting. Thanks for watching!!

Nice idea, especially if you do not have a lathe. Seems if have a lathe you could make the frame for the router that mounts on the bed of the lathe. A a lathe would spin much more exactly and at greater speed if needed. You would have two hands to work with too but the homemade jig could be rigged to be hands free too.

@sawyerrob949

5 жыл бұрын

That is exactly what I did. SR

Try a "dish cutting bit". They have a flat bottom and radius corners. I think you'll get better results. I don't see how you can avoid tear out on pre-drilled holes. To drill perpendicular holes in round stock: 1. make a "V" cradle to hold the stock and center it under the bit on the drill press. 2. drill the first hole. 3. insert a dowel into the first hole and turn the stock so that the dowel is parallel to the drill press table. 4. drill the next hole.

@parillaworks

5 жыл бұрын

Love the dish/bowl/tray bit idea. Surprisingly, I didn't get any tearout on the edges of the pre-drilled holes. I was expecting at least some but they were really clean.

Only a suggestion fix the drill/motor in place and lock the trigger down. You will get less movement of the drive pin and both hands on the router. O and scrap wood under the Forster bit when drilling they last longer.

@moehoward01

3 жыл бұрын

Rather than tube bushings, you might consider roller bearings. Less friction an wear.

If you just make a couple of holes in the side of your jig you can place and fix a plate similar to your tailstock end of the box inside the jig and adjust the working length of your part!

@parillaworks

5 жыл бұрын

Yup, I did something similar. I made an additional tailstock and all I needed to do was clamp it in place. Worked pretty well on the first try.

@timothyrobinson8640

4 жыл бұрын

@@parillaworks You could make a tailstock plate and house it in a series of dadoes inside your jig box serving to index the jig for whatever size stock you want to end up with.

Next time you try sanding your rough dowels use a flat wood backer. Doing it by hand will allow a variation in the finished size. Your soft hands end up following the early and late grain fluctuations in the growth rings. They are softer and harder. I found out the hard way quite a few years ago in the late 80's when trying to sand things really evenly. A backer block is your friend. Mark Cabinetmaker for a long, long time.

@parillaworks

5 жыл бұрын

Thank you, this was probably the most helpful tip so far. I think it will also save my fingers from getting caught in the predrilled holes. Thanks!!

cool

Check out Izzy Swan's dowel-making setup for the tablesaw too.

What did you use in the router wall to make the drive screw to spin on ? great video

Not sure if anyone has suggested this, but maybe try plunging your router bit to the side of the dowel. That way a cheap straight router bit will cut way better than anything coming in from above.

Muy buena idea, excelente dispositivo o plantilla para hacer palos redondos.. Felicitaciones 👍🏽 y Gracias por compartir tus conocimientos y experiencias... Saludos Cordiales desde La Rioja-Argentina

@arthurchenoweth7897

5 жыл бұрын

Complicated rigged lathe

@ramirod2029

5 жыл бұрын

Argentina. Wow es in paso bastante largo. A donde estamos nostros. Que estamos in el estado de Massachusetts an La nueva Inglaterra we los Estados Unidos. A que the dedicas mi Hermano latinoamericano?

@exequielarcelobos4679

5 жыл бұрын

@@ramirod2029 Estoy empezando a dedicarme a la carpintería... Tus vídeos son de mucha ayuda para personas que recién empezamos en el oficio 😊

@ramirod2029

5 жыл бұрын

@@exequielarcelobos4679 Que irramientas tienes? Estas bien equipado? O solamente tienes un cerrucho y in martillo?

@exequielarcelobos4679

5 жыл бұрын

@@ramirod2029 Hola! Tengo algunas herramientas eléctricas , de mano y unas de banco q contrui yo mismo por ejemplo adapte a una mesa una sierra circular de mano y a un taladro manual construi un dispositivo para que funcione como uno de banco... Con esas herramientas me doy mañas para trabajar

Izzy Swan has a tablesaw version of this jig.

@jarodmorris611

5 жыл бұрын

I was just thinking "Why is it better to build this instead of one over the table saw like the Wizard of iz.

@bullfrogpondshop3179

3 жыл бұрын

I've seen several table saw versions and they all seem safer than trying to operate a router with one hand. My two cents...

Молодец!

Nice stop action on assembly. Dust collection as simple as a shop vac port in the side of the frame would help. Also, I’d be looking for a way to turn the drive without hanging on to the drill. Not sure how many rpm you need to do the job, I’d expect not too much. Possible strap the drill to the side of the cabinet and rig up a simple belt drive on wooden pulleys cut with a hole saw. In my case, I’d be trying to use an old smaller sized electric appliance motor w/o too many rpm. But heck... guess you could do it with a rope wrapped around a wooden disk and a return spring, and work it like a treadle. Or just use the drill. Haha

@parillaworks

5 жыл бұрын

Thanks for the comment Ralph! I'm going to try to mount a drill next to the jig so I can focus on the router.

Very smart, but to complicated for me👍

Now to make these 12 feet long!

You put an offset sled with a bolt from the side for sizing your dowels that way your bit doesn’t matter because the adjustment is from the side. Way more precise also.

@parillaworks

5 жыл бұрын

I see. Something like metal lathe carriage, that would work well if I could build it reliably.

Weird thought, but it could also double as a router planing sled with an addition or two to the design.