Perfect! 👌

There is one highly misleading mistake: The adjustment ring is taken off in a far right position (2:05) while it is mounted back in a far left position (3:20) . This should in practice lead to impractical coarse grind settings - when following blindly. In general I like all the clear explanatory videos and to me they were mostly extremely helpful.

@MahlkoenigGrinders

5 ай бұрын

Thank you for the feedback.

Great video! Thank you for sharing! do you know how to update the E65S GbW software? I heard there is a new firmware version.

@MahlkoenigGrinders

2 жыл бұрын

We recommend speaking to your local Mahlkonig dealer. please see the dealer section of our website to locate. Thank you

@fagyasi

6 ай бұрын

If u are home barista there's no point to update lol😂😂

How often should this be done and how often flapper needs be replaced, please? I pull 4, 5 espressos a day. :)

@MahlkoenigGrinders

Жыл бұрын

We recommend 800-1250 kilos but will depend on the roast of coffee you use.

This looks like the dream grinder for home use. Is a smaller hopper available for under home kitchen cabinets (under a counter)?

@friedlotto

3 ай бұрын

Yes there is. Definitely recommended for home use.

@MahlkoenigGrinders

2 ай бұрын

Yes, it is! www.mahlkoenig.com/products/e65s-e80s-bean-hopper-small

Has the zero point (Nullpunkt) to be set a new after cleaning? I think it should stay the same as before the cleaning, right?

@MahlkoenigGrinders

2 жыл бұрын

Yes, exactly. The zero point should not change after cleaning.

@AdamHellacopter

2 жыл бұрын

Good video, slightly confusing though, probably the edit. When releasing the adjustment ring the shot from above shows that it’s in the middle, then when it’s taken off it’s turned from finest to coarsest (0 to 8). Then putting it back on to align it with the marker 0 position again, next shot from above is in the middle. Now that’s where it gets interesting. Took it apart, put it back exactly as it was, didn’t change or turn a thing. In 0 position the grind is extremely coarse, it shows on the screen as well how open the blades are. Any ideas what could have gone wrong?

@jboy3421

Жыл бұрын

@@MahlkoenigGrinders you didn’t seem to remove the grind adjustment ring at the zero point (you removed it at a courser setting) but you put it back on at the zero point marker.. This’ll throw the calibration out in terms of the zero point in relation to the number scale and thus it’ll be much courser at the zero point now than it originally would’ve been. It would’ve been fine if the grinder was 're-zeroed' afterwards but that wasn’t shown in this video. We’re trying to use these videos as a tool for the less experienced baristas in the cafe that I work at and sometimes in this instance this would cause miscalibration and even more confusion..

My E68S grinder stalls after one espresso grind. How do I fix it. Its less than a year old.

@MahlkoenigGrinders

2 жыл бұрын

We would recommend a deep clean and also inspect the burrs. If you are still having issues please contact a local engineer for assistance. Thank you

I have the rubber flapper with steel thing. How kt shoukd be insert. Rubber flapper first and steel thing behind it? Thanks 3:31

@Vagkoul

19 күн бұрын

the metal thing should be closer to the burrs, the silicon flapper should be facing outwards, to the exit of the grinder. The metal is supporting the flapper (therefore behind the flapper) to break the clumps. Hope that helps

@MiloslavSirovy

18 күн бұрын

@@Vagkoul thank you 🙏