Loved the process of rebuilding the broken crank shaft / Amazing
Loved the process of rebuilding the broken crank shaft / Amazing #loved #process #repairedking #broken #croken #shaft
Жүктеу.....
Пікірлер: 381
@user-mb8be2bn9b Жыл бұрын
молодцы. теперь покрасить зеленой краской и выбросить.
@rolandburisch9489 Жыл бұрын
There are many such video clips of differential gears being repaired, crankshafts, camshafts, etc, but how come we never see the engine running? How come we don't see what it's like six months from now? I have my doubts and I don't think I'd like to be around when the customer comes back asking for a refund. Alex Ivanov, below, no, it's not cast iron. It's cast steel, look at the swarf while it's being drilled. Cast iron swarf is granular, steel produces spirals. An HT welding rod will do it but then the pinning bolts should also be HT. But they would appear to be mild steel because they're galvanized. HT cap screws or hex sets are black as a rule.
@heinzfissimatent4294
Жыл бұрын
hahaha only for return customers.
@obrobkacnc4568
Жыл бұрын
Because it doesn't work!!! This crankshaft will work to the first major load.
@johnye4433
Жыл бұрын
Steel repairs are not supposed to last long but long enough for the other existing cracks to fail first, that is the economic for repair, it is meant to get the last ounce of use out of an otherwise full of cracks part
@lindsaythomas2283
Жыл бұрын
What is the purpose of the 2 "pinning" bolts?
@johnye4433
Жыл бұрын
@@lindsaythomas2283 to increase the contact between two sides beyond just the seams
@user-mg9gw4ir2m Жыл бұрын
Ничего более шокирующего на этом канале я ещё не видел!
@user-lo8wf2gi1j
Жыл бұрын
Еще наверное молод не такое увидишь за свою жизнь,мудаки везде есть,еще не то сделают.
@user-cd9ud4xu1q Жыл бұрын
Теперь и умирать не страшно . Видел в жизни почти все .
@user-wo3hm6mc2p Жыл бұрын
Сижу на полу в гараже режу резьбы метчиком, а сам думаю , че там пацаны в Пакистане делают?
@vanquynguyen8298
Жыл бұрын
Họ đang chứng minh những gì anh học trong trường kỹ thuật cơ khí là sai bét cả !😁
@user-qc5xz8mz1v
Жыл бұрын
😂😂😂
@mirza-sons
Жыл бұрын
😆😆🤣😝😝😝
@1kot4u Жыл бұрын
that is a cast iron crank that never welds, it will snap again along the welding seam. steel bolts have different thermal expantion and will cause bending forces inside, and which is more the bearing surfaces are riuned, there is no way to polish or ressurect them. the crank is trash. p.s.someone tell them to measure bearings instead of oil seal surface
@getov1147
Жыл бұрын
Also they can't set up degree rotation. Indian job.
@juanjosehernandez6625
Жыл бұрын
Completely agree.
@akhil999in
Жыл бұрын
@@getov1147 pakistani, by dress
@12vince80
Жыл бұрын
@@getov1147 they are Pakistanis
@alyahyamo
Жыл бұрын
They just doing it for youtube views and subs, any low skill mechanic will know this is usless
@user-ur4bu4lt9e Жыл бұрын
Блин всё варят у них наверное пластиковые и деревянные электроды есть и бетонные 😂😂
@user-xk8pe1zc5q
Жыл бұрын
ну и резиновые тоже,мало ли шланг заварить.
@mrnobody1897
Жыл бұрын
а в аптеке электроды по мясу купить можно
@finney67 Жыл бұрын
This is why everything is endlessly under repair
@user-hu8wh5hr2u Жыл бұрын
Ещё косынками надо усилить, чтобы дольше ходил.
@user-uj5ew1rg4o
Жыл бұрын
суперклей и сода явно помогут
@user-vf6tw2gj8v
Жыл бұрын
Ну не ужели они на столько тупые?я просто не очень в сварке и железе.....за каким то хером они пытаются сварить коленвал))))
@konstantine_2217
Жыл бұрын
как ни странно но в советские времена и у нас такое практиковали с 2 колен варили 1, только балансировать необходимо
@user-yu5by7nb8r
Жыл бұрын
@@konstantine_2217 ну не так похабно,как здесь...Такое купит только перекуп...
@user-yu5by7nb8r
Жыл бұрын
@@konstantine_2217 это рентабельно ?!
@straus8998 Жыл бұрын
Работы нет, давай хоть кино поснимаем))). Для металлоприёмки)))
@FairladyS130 Жыл бұрын
That's probably one of their home made cast cranks which broke, it will break again for sure.
@hankjones2975
10 ай бұрын
it is forged. I am a machinist and the crank is probably at least 4140. rod most likely 7018. half the tensile strength of the crank. he didn't v it out, not that it would of help. no penetration and welding alloy steel. zero chance it will work.
@user-uj5ew1rg4o Жыл бұрын
да это чисто для видосов,для движухи канала на камеру делают, а потом выкинут
@shanerorko8076 Жыл бұрын
This is fake, that crank would snap straight away as the weld is in the area where the force is high. You can weld on cranks but not on a fracture like that. These guys are just doing this for a video the crank will never be used.
@user-jg7tx5dt3q Жыл бұрын
Видимо коленвал лопнул по сварному шву после предыдущего мастера, у которого были просроченные электроды
@user-xk8pe1zc5q
Жыл бұрын
не скорей всего не было чугунных электродов,он резиновыми заварил.из-за этого и лопнул.
@ainurainur6166
Жыл бұрын
Ахах 😂😂😂
@user-vg3wd7tp6o Жыл бұрын
Хотелось бы увидеть,как на долго хватило этого вала? На запуск,или на два?
@user-lo8wf2gi1j
Жыл бұрын
Ты не поверишь но на долго если в сервант поставить и не ронять.
@user-qu2oi4oq8f
9 ай бұрын
Еще походит. Ну а развалится можно еще раз сваркой приварить
@user-yg9nj3ir9k Жыл бұрын
На совесть делают чтоб клиент далеко не уехал он обязательно к ним вернётся с благодарностью
@Zritel32
Жыл бұрын
или с пистолетом)))))
@Johny57010 ай бұрын
Надо было еще синей изолентой замотать, тогда точно долго проходит.
@user-ss7lz5ls8w
8 ай бұрын
Ты привари мне как нибудь я домой приеду изолентой заматаю 😂
@rockvillemike6062 Жыл бұрын
Such perfection! and it comes with a 3 mile or 30 minute warranty. Pure BS
@EssentialComment
Жыл бұрын
I would call it a "wave" warranty, If you cannot see them waving it's out of warranty
@dennisyoung4631
Жыл бұрын
Forty seconds, or forty meters, hic!
@YACIK. Жыл бұрын
Работа может и отличная но бестолковая!
@billville111 Жыл бұрын
Wood glue works well too.
@user-bs7sf8mp2q Жыл бұрын
Японский инженер застрелился от просмотренного видео. Ни или деталь делают на постамент в музей....
@denniskazich7559 Жыл бұрын
I'm pretty sure a crankshaft should not be welded and then be trusted to last.
@countrymoonshiner2300 Жыл бұрын
Я просто оxyeл! Электрод, болт, ножовка, сварка через подшипники, сверление коленвала, и т.д.
@georgyvahrushev3908
Жыл бұрын
"а что, так тоже можно было?", (С)
@v.d.5242
Жыл бұрын
Это видос для просмотров. Они снимают черти что, лишь бы денег заработать 😂
@user-ur4bu4lt9e
Жыл бұрын
@@v.d.5242 Да думаю не только и ставят такие и двигатели в песке перебирают, я сам в шоке от этих мастеров, так ещё и с нуля колена делают на коленке вот они и ломаются😂
@user-ly1ez9jh7z
Жыл бұрын
Пипец варят даже шейки коленвало неприкрыты.
@user-rz3tq7ch1v
Жыл бұрын
Я так понял о балансировке они не знают.
@mrb.5610 Жыл бұрын
Commedy gold !
@user-ht5hl4nq1t Жыл бұрын
И насколько его хватит до первой нагрузки на двигатель
@user-ur4bu4lt9e
Жыл бұрын
Поставят заведут, газу дадут и опять варить😂😂😂
@user-ef1nq8sf6c
Жыл бұрын
ЛАДНО ЕЩЁ ПОРШНИ ГОРЕЛЫЕ С КОНСКОЙ ВЫРАБОТКОЙ В ОВАЛЬНЫЕ ЛЫСЫЕ ГИЛЬЗЫ ЗАСОВЫВАЮТ И СОБИРАЮТ ! НО КОЛЕН. ВАЛ ЛОПНУТЫЙ ВАРИТЬ И СЫРЫМИ БОЛТАМИ СТЯГИВАТЬ ЭТО КОНЕЧНО ТАЛАНТ !
@skazka_tale8377
Жыл бұрын
@@user-ur4bu4lt9e ++ надо было проволкой замотать и еще походит
@acbdcd1897
Жыл бұрын
Это на авито...
@user-ef1nq8sf6c
Жыл бұрын
@@acbdcd1897 КУПИЛ ТАКОЙ?
@b.abrackus6403 Жыл бұрын
Anything can be "fixed"....but l guarantee that this crankshaft won't hold up once installed... l know how they abuse and overload their equipment in those countries.
@jeancontreras5980 Жыл бұрын
Hola saludos desde Venezuela.. Que buen trabajo... pero no entiendo porque Reparan algo y al mismo Tienpo tratan de Dañar otro... se Devio Protejer los puños donde van laa conchas de Vancadas y de las Bielas ese Cromo es Muy Delicado.. para próximos trabajo protejalos exitos y muchas Felicidades... Exito Dios Bendiga esas Manos hombre luchadores...
@user-cq1lu6xv1p Жыл бұрын
Я надеюсь это ж прикол был? Типа потроллить решили сообщество?
@takarifsalafiya Жыл бұрын
Pure Comedy.
@timothygeiger8271
11 ай бұрын
Yep, that crankshaft will make a good door stop, or boat anchor😆
@georgesam7805
9 ай бұрын
C'mon. Don't be a hater. That was a legit repair. I've done that a bunch of times. Everything from big diesels to nascar engines. They all hold up perfectly. The only thing I would have done differently is use softer bolts. Those ones looked too hard. 😂😂😂😂
@fernandobaqueromoriche44268 ай бұрын
¿ Que garantía le darán al cliente por este trabajo? Unicamente puede durar si lo guarda en una caja bien envuelto y engrasado. ¡ Vaya chapuza!
@user-re5mj9ww9o9 ай бұрын
Это наверное шуточное видио?😂 Такой коленвал обычно на переплавку отправляют. Не забудь зашпаклевать и подкрасить .
@user-rg6lb4pq5l Жыл бұрын
Тут даже я "прикуел"!
@titob.macaraeg157911 ай бұрын
I cant imagine if it survive for a week. Anyway thankyou for your effort.
@Imnotyourdoormat Жыл бұрын
Somebody forgot to tell these boys....."You cant do that."
@txkflier10 ай бұрын
Well, it passed the thumbs up test. I wouldn’t waste my time putting it back into the engine..
@Mswinner197510 ай бұрын
Коленвал на болтах скрутили. Оригинально!😂
@WardDorrity9 ай бұрын
That should last maybe a day or two. Operators in that part of the world routinely overload or otherwise operate their machinery well past reasonable parameters. Always.
@phucthienvo2240 Жыл бұрын
Very good😍😍😍😍😍😍😍😍😍😍😍😍😍😍
@valdemaroffvaldemar2752 Жыл бұрын
гараж 54 пусть сделает испытание,им один хрен нет чем занятся)))
@user-th8yd1cr3b
Жыл бұрын
Уже есть к жиговскому мотору добавили ещё два цилиндра
@user-uk5jb3kp5p Жыл бұрын
Вот откуда берутся контрактные запчасти без пробега по РФ
@user-cd9ud4xu1q
Жыл бұрын
такие запчасти только на украину поставляют
@kurtjammer9568 Жыл бұрын
That's why they are so busy..substandard repairs.
@richardluce775 Жыл бұрын
Never drive farther than you want to walk. Just sayin.😊
@user-zb1mp8ps1b Жыл бұрын
это наше ближайшее будущие! уже законодательно разрешили использовать восстановленные запчасти....
@robertorivelino2588 Жыл бұрын
But and the balance of This crankshaft , excelent and nice job congratulatiins
@user-ie4os2mj1g Жыл бұрын
Без синей изоленты ничего не получится
@hadjhadji6174 Жыл бұрын
النهاية لا زالت بها نقائص واضحة و المهم شكرا على العمل و الجهد المبذول
@user-ss7lz5ls8w8 ай бұрын
Интересно у них есть бог сварочного аппарата или электрода? 😂
@brentsumner6548 Жыл бұрын
That crank is good for another 100,000 km I'm sure
@philliphall5198 Жыл бұрын
They AllWAYS have a helper who is learning the skills Strong people and hard working
@johnfairchild3421
Жыл бұрын
You can learn alot
@stevenhorne5089
Жыл бұрын
They're dumb as a stump and spreading their stupidity.
@user-bp9mk7bc5x Жыл бұрын
Изначально это вал выработал себя на 1000% они его ещё ремонтируют, его место в металлоломе.
@johnfairchild3421 Жыл бұрын
Reminds me of the early nineteenth century
@BobSmith-mc7uq2 жыл бұрын
Nothing amazing about it. This crankshaft is out of round, out of balance & the structural integrity has been compromised. Klinger.....you screwed the pooch on this one...GUARANTEED comeback!!
@leonv1553 Жыл бұрын
Hello ATO. That all looks like a carpenter fixing a table leg. Dowel pegs and all. This must be one of those scrap bin jobs where busted parts are “fixed” for the video. Sure hope Utube pays them well. On the other hand, that’s probably a crankshaft for a top fuel dragster. Maybe John Force Racing gets their cranks from ATO. Always wondered what those fender stickers stood for. Now we know.
@davidbradford54322 жыл бұрын
So it will make a good post for a be mail box.
@garyr7027 Жыл бұрын
When you're bored and just want a reason to make a video... if you repair it they will watch.
@vagsonmendonca459511 ай бұрын
Loucura isso é aventura de mecânicos irresponsáveis, isso vai arrebentar fazendo um regaço no bloco, não gostaria de estar por perto,só Deus na causa.
@user-ie5hc6pb5r Жыл бұрын
На эпоксидку быстрее , а можно просто тфу сделать ,! Контрактный коленвал !
@user-ze1ik3ph2y Жыл бұрын
Просто жалко этих людей.
@vanquynguyen8298
Жыл бұрын
Điều kiện ở đó khó khăn thì biết làm sao ?
@65-Region
Жыл бұрын
@@vanquynguyen8298 мы знаем как вы там живёте, да и мы не сладко живём)
@user-qc5xz8mz1v
Жыл бұрын
@@65-Region не жалуйся,мы живём определенно лучше
@user-sx3kn9iz5j
Жыл бұрын
@@65-Region за всех не говори кто хочет хорошо жить он добивается этого и не ноет
@il_magnifico
Жыл бұрын
@@user-sx3kn9iz5j ну да. Расскажи как и чего ты добился? Наверное, все нищие мечтают недоедать? Пацану из бедной семьи из умирающей деревни где нибудь в тайге, конечно, только захотеть и стоит, чтобы "всего добиться"
@user-oc3jm3bh9e Жыл бұрын
Напомнило басню ,, Обезьяна и очки"
@erfankhalili11508 ай бұрын
Nice comedies. 😊
@CONTACTLIGHTTOMMY9 ай бұрын
I would never put that crankshaft in a mobile application, subject to starts, stops, sudden loads. Maybe continuous duty in a water pump or generator etc. And even then...light loads.
@alfrescabanilla2504 Жыл бұрын
make video to prove that this crank is functional...
@txrick4879 Жыл бұрын
Guaranteed till it breaks .
@mbclsshorts Жыл бұрын
Bad weight balance of the crankshaft will be the last problem here... :)
@user-eu6qx5xd2f Жыл бұрын
Шейку вала не закрыл от брызг от сварки,всю засрал , бесполезный труд все это . Гарантия пожизненная пока электроды не закончатся.
@davidhile5363 Жыл бұрын
Just use hot glue. That’s how they build all their free energy devices !!!
@user-gu6lw7wl7i Жыл бұрын
Балансировка коленвала? Не, не слышал!
@juliocesarbarbosa8266 Жыл бұрын
Nossa, esses caras são doidos. Da o maior trabalho tirar o motor, desmontar,retificar, montar de novo e colocar no lugar pra fazer uma gambiarra dessas, eu aposto que não dura nada. Eu achava que o Brasil era precário...
@cvptonin
Жыл бұрын
Kkkk, acho q é só pra fazer o vídeo. Íntegro ele já quebrou, imagina com esse remendo.
@alessandroanderson7780
Жыл бұрын
Sem falar que nem vai ficar desbalanceado, o motor vai tremer mais que um 3 cilindros 🤣🤣🤣
@WowAmazingRestoration7862 жыл бұрын
Good job
@bobhenry6159 Жыл бұрын
16:33 ..and it's ready for years of service....holding your potted plants. 🤣
@countrymoonshiner2300 Жыл бұрын
Зачем болты с боков, что они будут держать? Судя по их вектору - ничего!!!
@acbdcd1897
Жыл бұрын
Красиво же!!!??? И миллион просмотров и коментов. А мы балбесы обсуждаем, это восток... И интернет... = деньги...
@alexking3272 Жыл бұрын
Ничего удивительного не увидел , у нас в России до сих пор так делают многие. Камазисты и не такое могут делать. У нас это считается, низкокласифицированный и дешёвый ремонт . Это и правда не надолго . Единственный плюс, что человек не без дела сидит.
sounds like they are dealing droids in the background
@lazerman1966 Жыл бұрын
Это музейный экспонат.
@gkhanjriii91-04 Жыл бұрын
One good launch at 5k RPM and the engine will grenade 💥💣🤭
@thezackseven Жыл бұрын
That will not hold, welding just the exterior of the crack does not fuse the center of the cracked part and will break again under load.
@Vip__honey2 жыл бұрын
amazing
@user-xg7hw8tf2n7 ай бұрын
Точность гарантировано до микрон😮
@user-to3je9er8k9 ай бұрын
Я так понял это контент для просмотров , а эта железка в мусор.
@utube1818 Жыл бұрын
Next time a break a leg, I will use there philosophy and put a plaster over the break.
@CONTACTLIGHTTOMMY9 ай бұрын
I fail to see the need for those bolts. Should cover the journal when welding close to it. This video must be for show only. After finishing watching the video, I can confidently state that crankshaft was never used again. Purely for some clicks.
@user-mb6fy9mf1f Жыл бұрын
Сразу видно что у них жизнь очень тежолая
@user-ly1kw5ox2d2 жыл бұрын
ну что --ох----но???? все четко канал мас-заделан...надежно красиво--КРАСАВА!!!!
@craig7350 Жыл бұрын
.. oh yeah, looks good, that will never break again .. lol
@craig7350
Жыл бұрын
.. as long as its placed directly in the trash bin, and not dropped there.
@Reis4four Жыл бұрын
Will explode the first time it fires on 8, the crack is still there and the oil passage is blocked as well.
@stevenhorne5089
Жыл бұрын
I like the way they just completely ignore the fact that they're welding the oil passage shut.
@ArtemAleksashkin9 ай бұрын
Советской школы сопромата на них нет...
@user-sd5fx6sm5d6 ай бұрын
Не дай бог от такого рукожопа получить коленчатый вал для своего движка. Спаси и сохрани.
@anastasiszaroliagis5066 Жыл бұрын
Most of the trucks over there running under those patents. Trucks are very old and there is no parts, this engine probably is of road engine for the fields or generator.
@Beenwala2 Жыл бұрын
Excellent work 👍
@lelionamirouche7569
Жыл бұрын
Really???😮😮😮
@brucemitchell5637
Жыл бұрын
BAHAHAHAHA!!!!!!
@dennisyoung4631
Жыл бұрын
Cosmetic “repair.” Maybe about 20% penetration on that weld, and soft screws.
@stevenhorne5089
Жыл бұрын
There's no way you can be this stupid.
@tecnomecanicacba1726 Жыл бұрын
Alta precisión!!! Jajajaja
@becarberrios904111 ай бұрын
Todo se puede soldar ....pero ningun trabajo tiene ningun tipo de garantia...soldar ..nos muestran que sirva es otra historia😂😂😂
@nickaxe771 Жыл бұрын
I suspect these guys have done this before.....ok would not happen in the west....but sometime we have to do what we have to do with what we have to hand. Yes I would like to see how it stand up in action....but at least they try.....maybe some are ok for a while and they are happy with that. If the could go to the dealership and get one off the shelf Im sure they would.
@johnfairchild3421
Жыл бұрын
This is like going to a discount parts place. Get you through a bind. Harbour Freight
@nickaxe771
Жыл бұрын
@@johnfairchild3421 Long as they are happy with the all is good.
@utube1818
Жыл бұрын
I appreciate what your saying, but at the end of the day there somethings that just cannot be repaired to a level required by the forces that are going to be applied. It's a matter of physics not economics.
@nickaxe771
Жыл бұрын
@@utube1818 Yes of course you quite correct.....but I wish I could find how long the job lasts till it fails.
@gielle30 Жыл бұрын
😱😱😱😱😱😱😱😱
@user-kh7rm3zm6l11 ай бұрын
يجب وضع براغي من معدن خاص لا يتمدد بالحراره
@mikhailhmelevski7419 Жыл бұрын
Сколько опилок в каналах для масла, потом задиры будут на вкладышах и он опять к ним же приедет но уже с другой причиной
@acbdcd1897
Жыл бұрын
Им пох....
@user-fs8gj2yh8c
Жыл бұрын
Ещё денег заработают
@rlprgp629 ай бұрын
I don't see how this repair will last, Is that crank even indexed? But the bolts that they are using, are they at least grade 8? Hmmm entertaining though.
@ebra5919 Жыл бұрын
خیلی جالب بود.👏👏👏👏
@daniellibsfrant4866 Жыл бұрын
Muy buen trabajo de torneado y soldadura, pero eso no aguanta ni 2 vueltas en un motor.
@robertomonteiro2171 Жыл бұрын
Na realidade deles rodou 6 meses está ótimo.
@eduardofreitasdjucks4868
Жыл бұрын
Nunca vi um serviços desse mas se rodar 6 meses tá bom demais ...
Пікірлер: 381
молодцы. теперь покрасить зеленой краской и выбросить.
There are many such video clips of differential gears being repaired, crankshafts, camshafts, etc, but how come we never see the engine running? How come we don't see what it's like six months from now? I have my doubts and I don't think I'd like to be around when the customer comes back asking for a refund. Alex Ivanov, below, no, it's not cast iron. It's cast steel, look at the swarf while it's being drilled. Cast iron swarf is granular, steel produces spirals. An HT welding rod will do it but then the pinning bolts should also be HT. But they would appear to be mild steel because they're galvanized. HT cap screws or hex sets are black as a rule.
@heinzfissimatent4294
Жыл бұрын
hahaha only for return customers.
@obrobkacnc4568
Жыл бұрын
Because it doesn't work!!! This crankshaft will work to the first major load.
@johnye4433
Жыл бұрын
Steel repairs are not supposed to last long but long enough for the other existing cracks to fail first, that is the economic for repair, it is meant to get the last ounce of use out of an otherwise full of cracks part
@lindsaythomas2283
Жыл бұрын
What is the purpose of the 2 "pinning" bolts?
@johnye4433
Жыл бұрын
@@lindsaythomas2283 to increase the contact between two sides beyond just the seams
Ничего более шокирующего на этом канале я ещё не видел!
@user-lo8wf2gi1j
Жыл бұрын
Еще наверное молод не такое увидишь за свою жизнь,мудаки везде есть,еще не то сделают.
Теперь и умирать не страшно . Видел в жизни почти все .
Сижу на полу в гараже режу резьбы метчиком, а сам думаю , че там пацаны в Пакистане делают?
@vanquynguyen8298
Жыл бұрын
Họ đang chứng minh những gì anh học trong trường kỹ thuật cơ khí là sai bét cả !😁
@user-qc5xz8mz1v
Жыл бұрын
😂😂😂
@mirza-sons
Жыл бұрын
😆😆🤣😝😝😝
that is a cast iron crank that never welds, it will snap again along the welding seam. steel bolts have different thermal expantion and will cause bending forces inside, and which is more the bearing surfaces are riuned, there is no way to polish or ressurect them. the crank is trash. p.s.someone tell them to measure bearings instead of oil seal surface
@getov1147
Жыл бұрын
Also they can't set up degree rotation. Indian job.
@juanjosehernandez6625
Жыл бұрын
Completely agree.
@akhil999in
Жыл бұрын
@@getov1147 pakistani, by dress
@12vince80
Жыл бұрын
@@getov1147 they are Pakistanis
@alyahyamo
Жыл бұрын
They just doing it for youtube views and subs, any low skill mechanic will know this is usless
Блин всё варят у них наверное пластиковые и деревянные электроды есть и бетонные 😂😂
@user-xk8pe1zc5q
Жыл бұрын
ну и резиновые тоже,мало ли шланг заварить.
@mrnobody1897
Жыл бұрын
а в аптеке электроды по мясу купить можно
This is why everything is endlessly under repair
Ещё косынками надо усилить, чтобы дольше ходил.
@user-uj5ew1rg4o
Жыл бұрын
суперклей и сода явно помогут
@user-vf6tw2gj8v
Жыл бұрын
Ну не ужели они на столько тупые?я просто не очень в сварке и железе.....за каким то хером они пытаются сварить коленвал))))
@konstantine_2217
Жыл бұрын
как ни странно но в советские времена и у нас такое практиковали с 2 колен варили 1, только балансировать необходимо
@user-yu5by7nb8r
Жыл бұрын
@@konstantine_2217 ну не так похабно,как здесь...Такое купит только перекуп...
@user-yu5by7nb8r
Жыл бұрын
@@konstantine_2217 это рентабельно ?!
Работы нет, давай хоть кино поснимаем))). Для металлоприёмки)))
That's probably one of their home made cast cranks which broke, it will break again for sure.
@hankjones2975
10 ай бұрын
it is forged. I am a machinist and the crank is probably at least 4140. rod most likely 7018. half the tensile strength of the crank. he didn't v it out, not that it would of help. no penetration and welding alloy steel. zero chance it will work.
да это чисто для видосов,для движухи канала на камеру делают, а потом выкинут
This is fake, that crank would snap straight away as the weld is in the area where the force is high. You can weld on cranks but not on a fracture like that. These guys are just doing this for a video the crank will never be used.
Видимо коленвал лопнул по сварному шву после предыдущего мастера, у которого были просроченные электроды
@user-xk8pe1zc5q
Жыл бұрын
не скорей всего не было чугунных электродов,он резиновыми заварил.из-за этого и лопнул.
@ainurainur6166
Жыл бұрын
Ахах 😂😂😂
Хотелось бы увидеть,как на долго хватило этого вала? На запуск,или на два?
@user-lo8wf2gi1j
Жыл бұрын
Ты не поверишь но на долго если в сервант поставить и не ронять.
@user-qu2oi4oq8f
9 ай бұрын
Еще походит. Ну а развалится можно еще раз сваркой приварить
На совесть делают чтоб клиент далеко не уехал он обязательно к ним вернётся с благодарностью
@Zritel32
Жыл бұрын
или с пистолетом)))))
Надо было еще синей изолентой замотать, тогда точно долго проходит.
@user-ss7lz5ls8w
8 ай бұрын
Ты привари мне как нибудь я домой приеду изолентой заматаю 😂
Such perfection! and it comes with a 3 mile or 30 minute warranty. Pure BS
@EssentialComment
Жыл бұрын
I would call it a "wave" warranty, If you cannot see them waving it's out of warranty
@dennisyoung4631
Жыл бұрын
Forty seconds, or forty meters, hic!
Работа может и отличная но бестолковая!
Wood glue works well too.
Японский инженер застрелился от просмотренного видео. Ни или деталь делают на постамент в музей....
I'm pretty sure a crankshaft should not be welded and then be trusted to last.
Я просто оxyeл! Электрод, болт, ножовка, сварка через подшипники, сверление коленвала, и т.д.
@georgyvahrushev3908
Жыл бұрын
"а что, так тоже можно было?", (С)
@v.d.5242
Жыл бұрын
Это видос для просмотров. Они снимают черти что, лишь бы денег заработать 😂
@user-ur4bu4lt9e
Жыл бұрын
@@v.d.5242 Да думаю не только и ставят такие и двигатели в песке перебирают, я сам в шоке от этих мастеров, так ещё и с нуля колена делают на коленке вот они и ломаются😂
@user-ly1ez9jh7z
Жыл бұрын
Пипец варят даже шейки коленвало неприкрыты.
@user-rz3tq7ch1v
Жыл бұрын
Я так понял о балансировке они не знают.
Commedy gold !
И насколько его хватит до первой нагрузки на двигатель
@user-ur4bu4lt9e
Жыл бұрын
Поставят заведут, газу дадут и опять варить😂😂😂
@user-ef1nq8sf6c
Жыл бұрын
ЛАДНО ЕЩЁ ПОРШНИ ГОРЕЛЫЕ С КОНСКОЙ ВЫРАБОТКОЙ В ОВАЛЬНЫЕ ЛЫСЫЕ ГИЛЬЗЫ ЗАСОВЫВАЮТ И СОБИРАЮТ ! НО КОЛЕН. ВАЛ ЛОПНУТЫЙ ВАРИТЬ И СЫРЫМИ БОЛТАМИ СТЯГИВАТЬ ЭТО КОНЕЧНО ТАЛАНТ !
@skazka_tale8377
Жыл бұрын
@@user-ur4bu4lt9e ++ надо было проволкой замотать и еще походит
@acbdcd1897
Жыл бұрын
Это на авито...
@user-ef1nq8sf6c
Жыл бұрын
@@acbdcd1897 КУПИЛ ТАКОЙ?
Anything can be "fixed"....but l guarantee that this crankshaft won't hold up once installed... l know how they abuse and overload their equipment in those countries.
Hola saludos desde Venezuela.. Que buen trabajo... pero no entiendo porque Reparan algo y al mismo Tienpo tratan de Dañar otro... se Devio Protejer los puños donde van laa conchas de Vancadas y de las Bielas ese Cromo es Muy Delicado.. para próximos trabajo protejalos exitos y muchas Felicidades... Exito Dios Bendiga esas Manos hombre luchadores...
Я надеюсь это ж прикол был? Типа потроллить решили сообщество?
Pure Comedy.
@timothygeiger8271
11 ай бұрын
Yep, that crankshaft will make a good door stop, or boat anchor😆
@georgesam7805
9 ай бұрын
C'mon. Don't be a hater. That was a legit repair. I've done that a bunch of times. Everything from big diesels to nascar engines. They all hold up perfectly. The only thing I would have done differently is use softer bolts. Those ones looked too hard. 😂😂😂😂
¿ Que garantía le darán al cliente por este trabajo? Unicamente puede durar si lo guarda en una caja bien envuelto y engrasado. ¡ Vaya chapuza!
Это наверное шуточное видио?😂 Такой коленвал обычно на переплавку отправляют. Не забудь зашпаклевать и подкрасить .
Тут даже я "прикуел"!
I cant imagine if it survive for a week. Anyway thankyou for your effort.
Somebody forgot to tell these boys....."You cant do that."
Well, it passed the thumbs up test. I wouldn’t waste my time putting it back into the engine..
Коленвал на болтах скрутили. Оригинально!😂
That should last maybe a day or two. Operators in that part of the world routinely overload or otherwise operate their machinery well past reasonable parameters. Always.
Very good😍😍😍😍😍😍😍😍😍😍😍😍😍😍
гараж 54 пусть сделает испытание,им один хрен нет чем занятся)))
@user-th8yd1cr3b
Жыл бұрын
Уже есть к жиговскому мотору добавили ещё два цилиндра
Вот откуда берутся контрактные запчасти без пробега по РФ
@user-cd9ud4xu1q
Жыл бұрын
такие запчасти только на украину поставляют
That's why they are so busy..substandard repairs.
Never drive farther than you want to walk. Just sayin.😊
это наше ближайшее будущие! уже законодательно разрешили использовать восстановленные запчасти....
But and the balance of This crankshaft , excelent and nice job congratulatiins
Без синей изоленты ничего не получится
النهاية لا زالت بها نقائص واضحة و المهم شكرا على العمل و الجهد المبذول
Интересно у них есть бог сварочного аппарата или электрода? 😂
That crank is good for another 100,000 km I'm sure
They AllWAYS have a helper who is learning the skills Strong people and hard working
@johnfairchild3421
Жыл бұрын
You can learn alot
@stevenhorne5089
Жыл бұрын
They're dumb as a stump and spreading their stupidity.
Изначально это вал выработал себя на 1000% они его ещё ремонтируют, его место в металлоломе.
Reminds me of the early nineteenth century
Nothing amazing about it. This crankshaft is out of round, out of balance & the structural integrity has been compromised. Klinger.....you screwed the pooch on this one...GUARANTEED comeback!!
Hello ATO. That all looks like a carpenter fixing a table leg. Dowel pegs and all. This must be one of those scrap bin jobs where busted parts are “fixed” for the video. Sure hope Utube pays them well. On the other hand, that’s probably a crankshaft for a top fuel dragster. Maybe John Force Racing gets their cranks from ATO. Always wondered what those fender stickers stood for. Now we know.
So it will make a good post for a be mail box.
When you're bored and just want a reason to make a video... if you repair it they will watch.
Loucura isso é aventura de mecânicos irresponsáveis, isso vai arrebentar fazendo um regaço no bloco, não gostaria de estar por perto,só Deus na causa.
На эпоксидку быстрее , а можно просто тфу сделать ,! Контрактный коленвал !
Просто жалко этих людей.
@vanquynguyen8298
Жыл бұрын
Điều kiện ở đó khó khăn thì biết làm sao ?
@65-Region
Жыл бұрын
@@vanquynguyen8298 мы знаем как вы там живёте, да и мы не сладко живём)
@user-qc5xz8mz1v
Жыл бұрын
@@65-Region не жалуйся,мы живём определенно лучше
@user-sx3kn9iz5j
Жыл бұрын
@@65-Region за всех не говори кто хочет хорошо жить он добивается этого и не ноет
@il_magnifico
Жыл бұрын
@@user-sx3kn9iz5j ну да. Расскажи как и чего ты добился? Наверное, все нищие мечтают недоедать? Пацану из бедной семьи из умирающей деревни где нибудь в тайге, конечно, только захотеть и стоит, чтобы "всего добиться"
Напомнило басню ,, Обезьяна и очки"
Nice comedies. 😊
I would never put that crankshaft in a mobile application, subject to starts, stops, sudden loads. Maybe continuous duty in a water pump or generator etc. And even then...light loads.
make video to prove that this crank is functional...
Guaranteed till it breaks .
Bad weight balance of the crankshaft will be the last problem here... :)
Шейку вала не закрыл от брызг от сварки,всю засрал , бесполезный труд все это . Гарантия пожизненная пока электроды не закончатся.
Just use hot glue. That’s how they build all their free energy devices !!!
Балансировка коленвала? Не, не слышал!
Nossa, esses caras são doidos. Da o maior trabalho tirar o motor, desmontar,retificar, montar de novo e colocar no lugar pra fazer uma gambiarra dessas, eu aposto que não dura nada. Eu achava que o Brasil era precário...
@cvptonin
Жыл бұрын
Kkkk, acho q é só pra fazer o vídeo. Íntegro ele já quebrou, imagina com esse remendo.
@alessandroanderson7780
Жыл бұрын
Sem falar que nem vai ficar desbalanceado, o motor vai tremer mais que um 3 cilindros 🤣🤣🤣
Good job
16:33 ..and it's ready for years of service....holding your potted plants. 🤣
Зачем болты с боков, что они будут держать? Судя по их вектору - ничего!!!
@acbdcd1897
Жыл бұрын
Красиво же!!!??? И миллион просмотров и коментов. А мы балбесы обсуждаем, это восток... И интернет... = деньги...
Ничего удивительного не увидел , у нас в России до сих пор так делают многие. Камазисты и не такое могут делать. У нас это считается, низкокласифицированный и дешёвый ремонт . Это и правда не надолго . Единственный плюс, что человек не без дела сидит.
เปลี่ยนใหม่เถอะพ่อคุณ หักขนาดนี้ยังซ่อมใช้งานอยู่ รึ
sounds like they are dealing droids in the background
Это музейный экспонат.
One good launch at 5k RPM and the engine will grenade 💥💣🤭
That will not hold, welding just the exterior of the crack does not fuse the center of the cracked part and will break again under load.
amazing
Точность гарантировано до микрон😮
Я так понял это контент для просмотров , а эта железка в мусор.
Next time a break a leg, I will use there philosophy and put a plaster over the break.
I fail to see the need for those bolts. Should cover the journal when welding close to it. This video must be for show only. After finishing watching the video, I can confidently state that crankshaft was never used again. Purely for some clicks.
Сразу видно что у них жизнь очень тежолая
ну что --ох----но???? все четко канал мас-заделан...надежно красиво--КРАСАВА!!!!
.. oh yeah, looks good, that will never break again .. lol
@craig7350
Жыл бұрын
.. as long as its placed directly in the trash bin, and not dropped there.
Will explode the first time it fires on 8, the crack is still there and the oil passage is blocked as well.
@stevenhorne5089
Жыл бұрын
I like the way they just completely ignore the fact that they're welding the oil passage shut.
Советской школы сопромата на них нет...
Не дай бог от такого рукожопа получить коленчатый вал для своего движка. Спаси и сохрани.
Most of the trucks over there running under those patents. Trucks are very old and there is no parts, this engine probably is of road engine for the fields or generator.
Excellent work 👍
@lelionamirouche7569
Жыл бұрын
Really???😮😮😮
@brucemitchell5637
Жыл бұрын
BAHAHAHAHA!!!!!!
@dennisyoung4631
Жыл бұрын
Cosmetic “repair.” Maybe about 20% penetration on that weld, and soft screws.
@stevenhorne5089
Жыл бұрын
There's no way you can be this stupid.
Alta precisión!!! Jajajaja
Todo se puede soldar ....pero ningun trabajo tiene ningun tipo de garantia...soldar ..nos muestran que sirva es otra historia😂😂😂
I suspect these guys have done this before.....ok would not happen in the west....but sometime we have to do what we have to do with what we have to hand. Yes I would like to see how it stand up in action....but at least they try.....maybe some are ok for a while and they are happy with that. If the could go to the dealership and get one off the shelf Im sure they would.
@johnfairchild3421
Жыл бұрын
This is like going to a discount parts place. Get you through a bind. Harbour Freight
@nickaxe771
Жыл бұрын
@@johnfairchild3421 Long as they are happy with the all is good.
@utube1818
Жыл бұрын
I appreciate what your saying, but at the end of the day there somethings that just cannot be repaired to a level required by the forces that are going to be applied. It's a matter of physics not economics.
@nickaxe771
Жыл бұрын
@@utube1818 Yes of course you quite correct.....but I wish I could find how long the job lasts till it fails.
😱😱😱😱😱😱😱😱
يجب وضع براغي من معدن خاص لا يتمدد بالحراره
Сколько опилок в каналах для масла, потом задиры будут на вкладышах и он опять к ним же приедет но уже с другой причиной
@acbdcd1897
Жыл бұрын
Им пох....
@user-fs8gj2yh8c
Жыл бұрын
Ещё денег заработают
I don't see how this repair will last, Is that crank even indexed? But the bolts that they are using, are they at least grade 8? Hmmm entertaining though.
خیلی جالب بود.👏👏👏👏
Muy buen trabajo de torneado y soldadura, pero eso no aguanta ni 2 vueltas en un motor.
Na realidade deles rodou 6 meses está ótimo.
@eduardofreitasdjucks4868
Жыл бұрын
Nunca vi um serviços desse mas se rodar 6 meses tá bom demais ...
@Plateu1
Жыл бұрын
Nem deve ter ficado desbalanceado HaHa