I knew of TIG, MIG and stick welding. Now I know about dirt welding

Those STEEL-TOE slippers are amazing. 😊

The theory seems to be: if an inch thick steel casting broke, a quarter inch thick superficial weld with oil in it will work just fine.

@shannonfamily

5 ай бұрын

I think, dirty and oily on top of dirty and oily cancels itself out. It'll be fine. On one hand I think...they know the roads, they say its good, its good. On the other hand, I think they just set up their next repair job. Either way anyone who's ever had to do bush repairs knows that the best repair is the one that holds and you use what you brung (AvE)

Holy hell, you know that baby was OVERLOADED!

А еще хорошо бы скотчем заклеить. И клеевым пистолетом..

@fermer_s_yuga

4 ай бұрын

Про синюю изоленту забыл 😅😅😅😅😂😂😂

Не знаю насчёт надёжности детали после такого восстановления, не могу об этом ничего сказать. Интересны два момента: 1) 8:50 и 10:00 Эти крепления срезали и не восстановили. Да и некуда их теперь приваривать. Они не нужны? 2) 30:28 Зачем крышку приварили? Там теперь плоскости от сварки восстанавливать придётся.

NICE, I like the layers, very artistic, its like a cake, weld, slag, weld, slag, oil , weld, slag, air gap, weld, paint, weld, the Germans need to take a page from this and maybe they can build a car that doesn't leak oil after 3 years

Вся беда у Хоттабычей в том, что мерой грузоподъемности автомтбиля является высота бортов.

@Barmaley80x

4 ай бұрын

Это ещё они чугунные заготовки не возят по дорогам, или камешки в пару кубом объемом... Там высота бортов не сыграет никакой роли.

That type of stress fracture + deformation has surely compromised the overall structural integrity of the assembly. But I don't imagine they let small details like that get in the way of their daily business. Just a guess, but I could be wrong....

@LuisMoonlight

5 ай бұрын

tienes que ponerte en el lugar de ellos , su pais a diferencia del tuyo y mio no tienen la posibilidad economica ni accesibilidad por mercado cerrado para comprar repuestos originales ; se siente que lo dices con una ligereza tremenda.

The man in the green clothes doing the welding, I've always liked his work on the lathe.

ГЛАЗА!!!

Варят они отлично. Непонятно только зачем крышку приварил.

I didn't understand tack welding that cover at the end. What is this?

There is a formula here: If you need it, figure out how to repair without buying a new one, and of course, low cost labor and re-use scrap material for structure strength and you are back in buisiness. Yes even in Canada we have to do an occasional "bush fix" and these repairs tell that story. Amazing what can be done with will and strength!

@Barmaley80x

4 ай бұрын

I think that "bush fix" only somethere in Australia.

@howder1951

4 ай бұрын

That would be a hot dry remote bush fix Here we have cold snowy remote bush fix@@Barmaley80x

I feel puting the mounting brackets you cut off back on, may be a good idea.... Just saying.

Looks like they welded over the dirt?

Just change a few things and it will be a great workshop. With very little money. 1. Clean the parts to be processed and welded. 2. Clean the workshop, especially the tools and machines. 3. Use protective equipment and do not work in slippers and work clothes that can be caught by the machine.

@ZerokillerOppel1

5 ай бұрын

And use work tables for goodness sake's...why always the floorcrawling....

@Barmaley80x

4 ай бұрын

​@@ZerokillerOppel1it's more interesting I think. In my country if you will crawling on floor, you will be frozen to floor. This is warm country.

@ZerokillerOppel1

4 ай бұрын

@@Barmaley80x 🤣🤣🤣

Oh Yes that's Bloody good grinding down the Weld , Its now going to be paper thin welding, I think now 14 mins it will last ? , Less ,

BU ARAÇA NEKADAR YÜKYÜKLEMMİŞKİ BU KOVAN KARPUZ ĞİBİ YARILMIŞ AMA USTALAR VİDOLARINIZI İZLİYORUM ĞÜZEL İŞLER YAPIYORSUNUZ MAŞALLAH SİZE ALDIĞINIZ ÜÇRETHELAL OLSUN

Вот что будет если вместо гипоидного масла лить воду в мосты

Good repair and good welding

I like these guys safety shoes and the guys welding helmet. 😂

You can tell by parts of the procedure that this has been done many times before this axle. Amazing result from primitive methods.

Now they can more overload the truck

long time no see what are you doing have you been healthy i hope so you are verry talanted in what you do as a machinist and repairman

Living in an almost purely disposal society, I find these videos very refreshing. There is something very satisfying about keeping things that are still useful, relevant.

very good job your my sawarna man

there's a lot of broken studs in that in the axle housing

Рассеянцам смотреть в новые технологии!😂😂😂

Yang ku suka dari channel ini Menampilkan daya kreativitas mekanik yang hebat Tentunya sangat berharga sesuai dengan bidang usaha ku

@amazingthingofficial2923

4 ай бұрын

Thanks

Aslam o alaikum bhai.. kitny ampare pr welding ho rhi hy

I cant figure out why they welded the temporary diff cover in place?

Купите китайский шахман, увезёт 20 тонн. Но думаю упрет и 30 тонн. Вам как раз это нужно. Ютуб переведи только для них.

I assume the truck has 2 axles? The pressure it would take to split the housing like that is unthinkable. Maybe 100k pounds on a 10 ton axle? That would do it….😮

Спасибо. Здесь наглядно видно, как производители экономят! Надо было либо металл толще делать, либо металл прочнее = дороже делать! Спасибо.

@fonkanzler5612

4 ай бұрын

Просто не надо на 10-тоннике возить 20 тонн, у них это повсеместно.

@VasjaLar

4 ай бұрын

@@fonkanzler5612 конечно, это 10 тонник думаете?

@fonkanzler5612

4 ай бұрын

@@VasjaLar Я образно, но посыл, думаю, понятен. Они машины перегружают, поэтому мосты и рамы лопаются. Причем все это уже варено-переварено не один раз.

To bi kod nas završilo u sirovini ili na otpadu, dok vi to napravite kao novo. Svaka čast. 👍👍

@joserivero5847

7 ай бұрын

Realizan buenos trabajos pero los trabajadores no se cuidan parecen pertenecer a la Hera primitiva, no tienen guantes, botas ,caretas para soldar,espejuelos para corte, espejuelos contra impacto un desastre

Beat the weld/ crack the weld/ then weld over the weld insane. Keep on trucking. LOL

real mechanics right here , instead of the over paid part swappers we have in the west .

@mvcybron

6 ай бұрын

Real mechanics? Seriously!

@kemottomtr

5 ай бұрын

Fine. Just try to weld broken conrod or coil spring and make them work again. Good luck

Please clean the welding area. Clean metal welds stronger.

@sararet5

7 ай бұрын

No. We like it this way.

Not amazing idea, the good way to fix

Ottimo lavoro, il camion viaggerà per molti anni. Saluti a tutti da Roma 🤝🇮🇹

@ZerokillerOppel1

5 ай бұрын

Don't think so...not when it's "repaired" like that!!

Highly skilled with perfect precious performance. Long live all with good health and with needy wealth. Respect females. Mother is goddess and father is god.

Be able to overload the truck even more now...for about 50 yards ...lol. Those lot never learn.

Put an 12 mm thick plate on the flange where the third member use to go. It will last maybe forever, at least it won’t break there again.

Thank god for safety sandals.

They didn’t even check to make sure the axle tubes were level either.

@kennethney4260

5 ай бұрын

They'll be level when the truck is on a side hill

That kind of damage happened due to overloading what a waste of time. The extra money they made they lost while the truck was down not good business.

You must remember these trucks run a about10 MPH top speed. Don’t you remember the clunkers in the wheels in Nam to keep the demons away?

In case your wondering, this is where OSHA gets their "How NOT to or Else" videos 😂

Lets all pray that axle didnt come from a school bus. Every rule of repair and welding was broken here.

@Happy357mag

6 ай бұрын

Clearly they don't go to school.

@RRaucina

6 ай бұрын

Good point. And kids dont overload axles. @@Happy357mag

It only has to last long enough for a spare to be sourced.

It needed a little paint and would be good as new.

Super jest ta Cześć od tuk tuka pospawana pozdrawiam serdecznie 👍👍👍👍

@Barmaley80x

4 ай бұрын

Говоришь почти по русски, я понимаю что это чешский.

The land of Akshan, are they all scoundrels, by League of Legends.

I give it 1 pot hole ...maybe 2 before it fails

They don't seem to make any attempt to clean the welded areas at all. They use the dirt and oil as a flux.

@Barmaley80x

4 ай бұрын

Больше грязи - шире морда.

The working process is interesting👏👏

Bare feet (slippers) wen on working Oxygen cut, Weltin metals & Angle grinder???

Stop complaining there doing it 😂

First thing is clean it. Welding with all that dirt and paint and oil on isn’t good at all.

Pakistani mechanic: Anything can be welded if you put enough dirt on it.

Some epoxy paint for more strength it will last a lifetime. Haha.

arent you supposed to clean the area before you weld so it doesnt break again. . He welds on top of dirt and rust. Not even cleaned once during the entire process. are these people just fithy in everything they do...even in food.

At least now I know it is a waste of time to preheat or clean cast iron before welding steel to it. Go figure! ; )

All I can say is that they have a job

I’d like to know what rod they are using? Even after running through oil and dirt it lays a nice bead as for the workmanship it will outlast the truck.

@jonjacobjingleheimerschmid3798

6 ай бұрын

Probably 6011.....maybe 7011.... But don't matter, cast doesn't take well to welding....it will break along the outside edge of bead due to crystalization....

@RRaucina

6 ай бұрын

The proper rod with a pre-heat and diligent cleaning might have made this hold for some time. @@jonjacobjingleheimerschmid3798

@ferstuck37

5 ай бұрын

I’ve used nickel rod to weld cast but you still need to heat

@jonjacobjingleheimerschmid3798

5 ай бұрын

@@ferstuck37 yah nickel rod " Super missile weld" seems to be the best...even better if layed over carbon rod.... But now we're talking a very expensive weld!

absolutely stupid way to repair a critical part, pressing down on bearing surface, no cleaning or weld prep, no checking if axles are straight,bloody embarrassing to any engineer

Those toe tector sandles

The big nose has biggest hydraulic machine

ремонт барбухайки ... кашмар 🤯

Excelente Amigo

Lesser known fact. The word 'scrap' doesn't exist in their langage.

Uh.............Why was that flat plate welded on.

Wear safety boots

Schön Ihr Laienschauspiel zu sehen , ohne jeglichen Sachverstand 😂😅😢

Probably, just “drive to home” repair.

When will these guys ever learn to Weld properly, Im no welder, This is what i call service welding, While it was split open should of Bevel the Bloody edges? It might of lasted another Day;? Now Maybe 1 hour Guys or less, 😊.

Усталость металла они об этом не слышали! Мы на работе меняем мостовые краны хотя они с виду как новые но они имеют микротрещины

残存応力が残っているから、また壊れるよ！

They work as fast as they can..because they don't make anything..that leads to shabby work..don't clean anything..the welds don't get any penetration...can't last.

PFUSCH!!!!

Clean the welding surface - DONE, preheat the metal - DONE 🧐🧐🧐

Почему не очистили место сварки!??? Халтура!

@user-pr3il4ot2e

5 ай бұрын

Всплыло вместе со шлаком. Главное, чтобы дуга не гасла и кратеров не было

It scares me just thinking about what caused a catastrophic break! Truck bed full of lead bricks going off a jump?? I'm not a welder by trade but aren't you supposed to pre-heat cast iron parts before you weld them? And aren't you supposed to clean the parts first or just gob a crap ton of weld beads on it and call it good? Love the shot when the head fell off the 100 yr. old hammer. Not exactly the type of repair you would expect from the Cat dealer!

@Barmaley80x

4 ай бұрын

This is not cast iron. Because after detail cranks there was only big one fatigue.

修理以前に、ホーシングが割れる事が異常。 そして、ホーシングなのにデフが入っておらず、蓋をしてただの車軸として使われてるのも異常(デフギア付いてたらあんな割れ方できない)

@Barmaley80x

4 ай бұрын

Всего лишь лишняя деталь... ни дифференциала, ни гипоидной смазки... Это как оси на садовой тележке.

내가 저 상황이였다면 절단면을 그라인더로 v커팅을 하고 용접한후 다른 보강을 했을듯

I have to hand it to them, they are trying to fix it the best they can with what they have. Maybe this is out of context, it may just be to get the unladen truck back from where it was. The brand new axle may be on back order due to supply chain issues.

@ZerokillerOppel1

5 ай бұрын

Well...maybe you're right there...at least I would hope so!!😮 That repair is a catastrophe waiting to happen...

It's a joke right? It will not last for even 2 days. It will be back again for repair soon. They weld over dirt? like really? And it is called "amazing repair"? It is actually more like "pissing me off repair".

@davez4172

6 ай бұрын

I trust any repair made by a guy using a cutting torch while wearing safety sandals. The floor is lava axle repair shop.

@user-dw1rq7iy7x

6 ай бұрын

​@@Fuckit96🎉🎉🎉

@user-dw1rq7iy7x

6 ай бұрын

​@@davez4172😮😮😢

@user-dw1rq7iy7x

6 ай бұрын

😢

@RB-qe6ko

5 ай бұрын

This is India. I have seen enough there.

Well it very worst than Colombia they work but like the other persons say before you do anything cleaning properly and when you finish cleaning again paint it but we live in the dirty society there 👎😴

I see the comments from the "experts" at auto parts malls. These trucks travel super-loaded along incredible mountain roads. Nobody asks: "How can you break a part like that, which was original from the factory?" In fact, after the "insane" repairs, the trucks are back on the road for miles.

@ZerokillerOppel1

5 ай бұрын

I've seen video's here of these Pakistani dudes "beefing" up leafsprings, casually adding the odd 3 or 4 leafs to a factoryspring (predominantly Chinese or Japanese trucks) only because they continuously overload these trucks like there's no tomorrow...🥴😅

@utube1818

5 ай бұрын

I'm sure your right, back on the road for miles and miles they may even reach double figures before failing again.

All of these videos showing bodged repairs to catastrophic mechanical failures are due to one thing. The ridiculous over loading of vehicles. Why would you put 40 tonnes on a truck designed to carry 20. Welding a cast axle housing even with the correct rods and pre heating is a no go even at best. Pointless repair

No penetration any welds

Look at Mohammed go! Who would have thought you could waste so much time and resources doing so little? Certainly not Mohammed!

Just another horrible repair. Do they do a shitty job on purpose for more views? Are they incompetent, or just con artists?

@Happy357mag

6 ай бұрын

I don't want your meaningless ❤️ but I would ❤️ an answer to my question.

@migueldenovi5873

5 ай бұрын

Clearly, those fixes work fine. If not, they would be out of business.

This is what happens when the trucks are constantly overloaded.

That’s got to be from grossly overweighted vehicle time and time again ! If that lasts I’ll eat my hat 🎩😂

@ran2wild370

6 ай бұрын

Considering how calm those mechanics - they suppose it will last for a couple of decades more. They trust in their welding skills.

from shit and sticks - as usual