Lexus IS250 IS350 Speedometer Tachometer Needle Repair Part 1| New Cluster Mileage Correction
Автокөліктер мен көлік құралдары
We disassembly a Lexus 2IS cluster to do the LEDs and needles.
I got a replacement gauge cluster from a 2008 Lexus IS250 but the mileage different. I cloned the mileage and odometer EEPROM from my original 2007 cluster to the new cluster using a $10 EEPROM Programmer.
I will be changing the backlight LED in this cluster and also redoing the needles in the next video.
DISCLAIMER: The information provided in this video is not how odometers are rolled back for criminal purposes. This video is for informational and educational purposes only. Misrepresenting mileage upon the resale of a vehicle without full disclosure is illegal. Reprogramming your own car's odometer or correcting a replacement unit is not illegal.
CH341A Programmer - amzn.to/3q29mMs (eBay - amzn.to/2LCjaOq)
PCB Header Pins - amzn.to/2YXjVET
Wire Wrapping 30AWG - amzn.to/2LCjaOq
Pry Tools - amzn.to/3aKjC5L
If you can't program it, try desoldering the SMD chip using an air soldering iron. amzn.to/3rGNgzL
LEDs:
Needle - #1206 Blue Right Angle: amzn.to/3frkNwV
Backlight - Blue #PLCC-2 (1210 3528): ebay.to/2OyFeKO
International LED PLCC-2 Options: s.click.aliexpress.com/e/_AFDD2M
International LED 1206 Options: s.click.aliexpress.com/e/_9ghaHA
If you need a replacement gauge lens for the scratched up one, they are like $30 from online dealers.
P/N: 83852-53730
Resources:
2002 IS300 Video: • Odometer Mileage Corre...
DrShock - • Modify the CH341A EEPR...
speedkar99 - • DIY Odometer Reprogram...
----------
Support the Patreon: / tunerwithkids
Merch Available: teespring.com/stores/tuner-wi...
Follow Me on IG: / tuner_with_kids
For questions and inquiries: tunerwithkids@gmail.com
-------------------------
#LexusIS250 #Speedometer #MileageCorrection
0:00 Intro
0:42 Trim & Cluster Removal
3:25 Original vs. Replacement Cluster
4:15 Cluster Cover Removal
5:00 EEPROM Cloning Cluster Data
8:20 Testing Cloned Cluster
9:40 Needle Removal
13:40 LED Circuit Board Removal
Disclaimer: "Tuner with Kids", the alias for the human content creator for this KZread channel, is not responsible for any damages, injuries, losses, or liabilities associated with any repairs, upgrades, or maintenance performed on yours, or any elses, vehicle/property whatsoever. No warranty, express or implied, is made as to the accuracy or completeness of any information provided within this channel. Viewing and using the “as-is" information of this channel is totally at your own risk. Always wear personal protection equipment and follow appropriate vehicle manufacturer service manual guidelines with original manufacturer parts only when performing any repairs, upgrades, or maintenance upon any vehicle/property. Please note that some of the links provided are affiliate links and I may earn a commission if you purchase through the links. I use all of the products shown and recommend them because they are from companies I have found to be helpful and trustworthy. Please let me know via email if you have questions regarding any of the products/tools used.
Пікірлер: 92
You're the best! I just reprogrammed a new cluster with my actual mileage to get rid of my burnt out needles. Total cost was around $80 including the spare cluster. Thank you!
@waltertembo5143
Жыл бұрын
P
@TunerwithKids
Жыл бұрын
Glad you knew how to do the programmer. Most people are intimidated by anything electrical and programming.
Wow how bizarre I just literally picked one yesterday because the front clear plastic casing was cracked and am going to put it in today. Talk about perfect timing for your new video upload and in depth instructions. Also noticed you are in that group on fb ;) Your videos are underrated and need more views and subscribers. I'll see if I can get you some 🤙
@TunerwithKids
3 жыл бұрын
Thanks. Working slowly to build the channel.
Just the video I been hoping you'd make. Thanks
@TunerwithKids
3 жыл бұрын
More to come!
Update ** thanks heaps man all done and dusted. Perfect explanation and help and with the Sports Luxury Auto column I just left the car turned while I did it :) Also I can't find my Fuse board inside my car under drivers side or passengers lol
@TunerwithKids
3 жыл бұрын
The fuse panel is the tan box above the parking brake. Has the diagram on outside.
This is what i have been hoping to do after fixing the gear shift hole plate
Great info Thanks 👍
Found a future project! Thanks like I didn’t have enough on my plate
@TunerwithKids
3 жыл бұрын
Glad I could help! Never have too many projects!
Is there a way to communicate directly on a question on my IS? Love your channel and I’m a subscriber.
Do you know how to replace the turn signal for the valenti euro winker 3 blinks. I don’t know how to get to the OEM blinker module.
I have the flicker issue on my tach needle. Is the issue in the needles themselves or an LED on the circuit board?
Do you know if I could just unsolder the chip from my cluster, and then solder it onto the new cluster?
To test the Cluster where you conect the power suply? and how many volts it needs to work properly?
I’m struggling with the two top clips, any hints or tips?
can I get a link to the program plz? thanks for sharing the vid.
Hey mate. Another awesome video. Thanks! Question….are you aware of any way to calibrate the speed component of these clusters? At 100km/h my Speedo is about 10% out…which is worth trying to fix I think :)
@TunerwithKids
Жыл бұрын
That’s normal for all cars due to wheel and tire size variations and wear.
@davef2415
Жыл бұрын
@@TunerwithKids thanks mate. I knew there was variance, just didn’t think 10%!was normal. Lots of Lexus forums seem to have folks talking about a similar issue. In some of those instances Lexus swaps the cluster unit and the issue is resolved…..so just figured it may have been something that could be changed with a little deeper knowledge.
Can a isf 2012 cluster be replaces with the older 2008/9 cluster? Because the analog feul and so are way cooler
@TunerwithKids
2 жыл бұрын
Yes but you will have a oil pressure light since regular IS doesn't have that sensor.
Can I just switch out the tach and speedo Needles. From a good cluster. Mine the needles don't light up
@TunerwithKids
3 жыл бұрын
You can buy it’s a ticking timebomb. These all will fail eventually due to age and heat.
great video. I'm trying to convert a Japanese cluster to English. is there any resources that you use to identify the language setting of the cluster within ASProgrammer?
@TunerwithKids
9 ай бұрын
No way to do it. Need new cluster
Hey bro, I want to power my cluster on the bench with a 12v power supply. Can you tell me which pin numbers I need to connect to on the cluster? Thank you.
@TunerwithKids
2 жыл бұрын
1 and 13 to GND, they are top and bottom on one end. 12 and 24 for 12V power on opposite side. The plug is numbered if you look close.
Can you share a picture of where exactly on the chip I will need to connect to read the chip?
@TunerwithKids
3 жыл бұрын
Look on the board. I think I mentioned the IC number printed on there. @ 4:52 there is a arrow.
a little bit of an oddball question but if I swap a canadian cluster (km) into a US car. (miles) will the odometer increase in km or will it still keep going up in miles as if its a US car?
@TunerwithKids
2 жыл бұрын
The car has same sensor but the cluster does the calculations for it’s units.
Any tips on how to dismantle the multi information lcd display on the cluster? Need to replace the polariser film on the small lcd screen.
@TunerwithKids
Жыл бұрын
That thing has like 100 solder points, I think. Hard to remove.
@duxz
Жыл бұрын
@@TunerwithKids thanks for the quick response. I am having the so called vinegar syndrome on both my LCD on the cluster and also the navigation screen.
Does the chip need 3.3v or 5v? Should we mod the programmer like in the is300 vid?
@TunerwithKids
3 жыл бұрын
Same mod needed. All vehicle applications need 5V to write.
@sirseriously
2 жыл бұрын
Fyi - instead of cutting traces and all, you can just jumper the 5v and 3.3v pins together and it will work. Just did my is250 cluster using this method. Still need an adapter for the pin out of the ic, but that part is easy with some jumper wires.
Any way to completely turn off the check engine light and traction control? I don’t have catalytic converters and i was planning to just put a sticker over the light but maybe theres another way to turn them off??
@TunerwithKids
9 ай бұрын
Nope. The 2IS will give 15 different warnings for one CEL.
@richardhernandez4372
9 ай бұрын
@@TunerwithKids yes im just wanting to completely turn off the light like unplug it or some sort
Hi again mate. By chance would you happen to have the pin out info to make the bench harness for this cluster?
@TunerwithKids
11 ай бұрын
Don’t recall. But it’s two opposite corner pins on one of the harness’
@davef2415
11 ай бұрын
@@TunerwithKids from the online diagrams I can find, pin 1 is earth, pin 24 is battery and pin 12 is ign+. However when I power up with my bench power supply, I get nothing. I know the cluster works…cause it fires up when I put it in the car. Don’t suppose there is any additional guidance you can lend? Cheers.
@TunerwithKids
11 ай бұрын
I just looked at my rear plug and it’s the bigger plug. 1&13 are ground (white/black) and 12&24 are spliced and used on mine light green and peach.
@davef2415
11 ай бұрын
@@TunerwithKids bingo! Thanks mate. The second earth (pin 13) was where I was missing. Thanks.
where to connect the power supply to start the odometer without putting it in the car?
@TunerwithKids
3 жыл бұрын
I have a harness. Pin 1 and 13 are ground. 12 and 24 are power.
Hi , are you in NY I have is 350 I would Lov to frozen the ODO?
@TunerwithKids
3 жыл бұрын
Nope in FL.
Do you know where the toyota lexus is250 meter computer board is?
@TunerwithKids
2 жыл бұрын
On the cluster?
Is this a service you’d provide? I recently bought an ISF cluster for my IS350 and the ISF cluster has way less mileage than my 350 and I’d want it to match my current mileage.
@TunerwithKids
Жыл бұрын
Try Tanin Electronics, they do it as a service. I only make DIY content for you guys to try.
@flint707
Жыл бұрын
@@TunerwithKids Right on Binh, thank you brotha. I reached out to them and am just awaiting a reply.
@flint707
Жыл бұрын
One more thing, Binh… I spoke to someone at Tanin about an ISF cluster I bought in KM and getting it switched to MPH, they said they can’t change that. Does tachosoft allow for that correction, or maybe even techstream?
@TunerwithKids
Жыл бұрын
No. Need an MPH cluster.
Do you have a link for the usb cords you used to connect the dash to your computer?
@TunerwithKids
2 жыл бұрын
I have videos where I show on to modify a board to read the eeprom. Check my videos on ECU or 1IS cluster.
@octobergaming5767
2 жыл бұрын
@@TunerwithKids is there anyway you can do this for me
Do I have need to unscrew the screws from the back if want to clean the front plastic glass but the inside?
@TunerwithKids
Жыл бұрын
Don’t do it. You’ll end up scratching it worse.
@Unsuccesses
Жыл бұрын
@@TunerwithKids so I have to get a replacement ? I think I used a strong abrasive product while cleaning the front temper glass and it seems it etched inside of the glass.
@TunerwithKids
Жыл бұрын
If you messed up the surface, it’s done. Get a replacement, they are like $30 at dealer.
@Unsuccesses
Жыл бұрын
@@TunerwithKids even if it’s the inside of the cluster lens? It seems like a dried up spray to describe lol
If I replace my cluster, will it show the original mileage, or the mileage from the new cluster? Thanks
@TunerwithKids
Жыл бұрын
Cluster eeprom holds mileage.
You reckon I can remove it disconnect it while it's still turned on ?
@TunerwithKids
3 жыл бұрын
Yea that’s an option too. I’ve driven my car in the driveway in and out of the garage without the cluster on. It doesn’t do any harm.
@johnnobravo1978
3 жыл бұрын
@@TunerwithKids yeah sweet I was thinking maybe disconnect battery while car is running but probably not a good idea lol
mine started going out (led needle), not gonna fix it... not worth all that work .
How do you leave steering wheel all the way out when off ?
@TunerwithKids
3 жыл бұрын
My wheel is manual, so I don’t know what it does if you have the luxury package with automatic tilt.
@johnnobravo1978
3 жыл бұрын
@@TunerwithKids ah ok all good maybe disconnect battery before i turn it off 🤔
@TunerwithKids
3 жыл бұрын
Maybe, most other lexus cars that have this requires disabling via Techstream. No options on dash or column.
@Mustafa12364
2 жыл бұрын
Manually move the steering wheel up, Set your car in neutral and then turn it car off, then put car back in park. (no need to turn the car on in order to put in park)
Where’s the part2
@TunerwithKids
2 жыл бұрын
Look at the channel video list
the original mileage should be stored in car's ecu. Do you really need to reprogram the cluster ?
@TunerwithKids
3 жыл бұрын
Not Toyota.
Just when I thought it was just as simple as replacing the led... but nooo... there's computers software envolve..oh well guess I'll have to pay 150$ to get it fix.
@TunerwithKids
3 жыл бұрын
Which part?
@ujayet
3 жыл бұрын
@@TunerwithKids the part where you identify the chip and then alligator clip it and did somethings in the computer..I just wanted to remove the needle and swap out the LED onto the old needle.
@TunerwithKids
3 жыл бұрын
Well that’s for programming the mileage. This was a replacement I bought to experiment on with soldering so i cloned my old cluster to match.
im guessing a lot of people made a few 1000 bucks from this vid lol. You know what i mean.
@TunerwithKids
Жыл бұрын
Most people don’t have the skills to do this. I get asked to do it all the time but I don’t have the time to mess with others stuff. It’s tedious work and not work it for me.
@aneeshprasobhan
Жыл бұрын
@@TunerwithKids i see