You can make these any color you want as long as there is a 1206 LED (preferably right angle) for needles and PLCC-2 for backlight. Check the links and info in description box. These LED are referred to as various numbers (metric and imperial).

The ultimate project would be to convert the cluster to a digital one in the future.

Great work! I wish I had your patience to do all these diy's. Now that I look back I'm glad that Lexus suckered me into buying an extended warranty which covered all the TSIB/TSB that I experienced i.e. dead speedo needles, failed nav screen, failed water pump, rear view mirror spotting, sticky dash, wheel bearing, windshield drip molding cracking, aux port static, cam gear rattle at start up, passenger lumbar adjustment electrical failure, etc.

@TunerwithKids

3 жыл бұрын

You basically named every issue that these cars experienced from new.

Man that’s very nice!! Would love to buy one from you

Phenomenal Work, if I knew how to solder I'd attempt this lol.

Looks great! I wish I have as much patience as you. I will have to hit you up one day to do a spare gauge for me. My is350 is my daily since my is300 is out of commission. I would have to buy a second cluster to mod then have the mileage match mine to do the swap.

I pulled out the needles at 0 mph and 0 rpm and after I fixed the led, I put them back at 0 and everything worked. There wasnt a delay with the needles for me

This looks amazing! I would absolutely love to purchase one if you sell them .

Nice Video man, my Rpm needle is flickering. I'd like to do the same, looked nice

Looks awesome

You are amazing. I wonder if the console light can also change? Cuz as you know, it’s green.

On my 07 IS250 the leds went out on the speed and tachometer, I found a guy on Craigslist who replaced both the LEDs with any color you want for $80. I live in California though

@TunerwithKids

3 жыл бұрын

I think that was Tanin Auto Electronix does the repairs and has a guy in WI and San Diego.

Omg can't wait to watch this. I need to fix mine. I need to change them to red tho

@TunerwithKids

3 жыл бұрын

Get the tools and LEDs. You can use any color you want. I want to do the IS-C needles now. They are all clear ones. When I find an IS-C cluster for the low, I'm going to get one.

Great job dude

@TunerwithKids

3 жыл бұрын

Thanks!

Hey bro thank you for the efforts that u do online to explain I've got the needle blinking sometimes so am looking to change it my question is it because of the needle or the led in the motherboard

@TunerwithKids

Жыл бұрын

LED on needle.

Did you think you're able to do the same for 2014 Lexus IS350 base with a base instrument cluster and clone it to a 2014 fsport instrument cluster? If you can let me know how much to clone the mileage.

Hey tho, I just bought a used 2014 lexus is250 F sport but the mileage is stuck 97,000 what I can do to fix it or do I have to take it into lexus dealership?

Good job

@TunerwithKids

2 жыл бұрын

Thanks

At 10:14 which is the check engine light bulb? And which type of Led would I need Please

3Q's I see your powering the instrument cluster with a bench adapted PC power supply , Which wires on the IS cluster are used Pos & Neg ( colors ) ? also are you powering with +/- 5vdc for LED's or +/- 12vdc or combination of both voltages ? thanks

@TunerwithKids

Жыл бұрын

Just 12V to the cluster power pins.

I’m installing vland headlights on my Lexus and boy can’t imagine how you have the patience

After doing this and putting my needles back, the rpm needle falls like 500rpm below zero. No matter where i set the needle it just goes back to the same spot. Doesnt matter if i do it with the car on or off. If i set it with the car on it will stay correct only until the next time i turn the car off. Any solution? Thanks in advance.

Hey, I removed the needles to get to the board and fix some dead LEDs and replace them. After putting everything back, I set speed to 0 and plugged it back in and all was good and I drove around. But then after turning car off, after a little while the speed and rpm needs seem to drop a tad below 0. RPM is very little bit below 0 but speed is quite a bit below 0. Then when I start up my speed is wrong because 0 is below 0 and hence all the speed reading is wrong. I took apart the lens and moved it back to zero and once again it worked until I turned it off for a while then it goes below 0 again. I thought I'd try moving it to 0 with the car on, so tried that and same thing. Worked until i shutdown and after a while dropped below 0. Have you ever experienced anything like this? Would really appreciate your help. Thanks

@TunerwithKids

Жыл бұрын

Not really. I always remove with them at like 30 or 40 mph/rpm and put back in same spot. I never pull them at zero. I may have adjusted gas and temp once or twice to get right. The gauges also self calibrate upon start up, so in theory they should reorient themselves.

@prot0type90

Жыл бұрын

Im having the same issue. Did you ever find a solution? Thanks in advance.

Hey I did this and messed up a bit with installating the needles again, like my tachometer is way below than it should be, it shows my ideling below 0, any idea how I fix it now? I tried to remove and put them again didn't work out

@TunerwithKids

3 жыл бұрын

You have to remove and lightly install back and get it back to normal again. It’s gonna be trial and error.

I need to know the connection u r doing to light up the cluster on the bench

@TunerwithKids

3 жыл бұрын

Ground 1/13 and power to 12/24 wires.

@AbabnehA

3 жыл бұрын

@@TunerwithKids appreciated dude

Hi Binh, that was an amazing work. I am interested if you can do work on my guage for me or at least give me some informations , very appreciated. Keep up the work , liked your channel.

@TunerwithKids

6 ай бұрын

I don’t do this for others. Just making DIY videos for those who are inclined to do it.

@user-ke1dk4db5q

6 ай бұрын

@@TunerwithKids OK Binh 👍 appreciated for your replied and thanks for the video. Keep up the good work but what software did you use for reading those odometer code , I got a newer used car to replace my old one, not pass smog yet. Newer one i believe prior owner changed with a new cluster and the odometer is lower then I saw on carfax witch I checked after I bought it, was about few months no record of it and i want to put last known plus couple thousand miles on to that. Lesson learned, should have left without buying it., now I have 2 to work on instead of one. Dmv probably have last record but they don't tell. And the speed needle not working. I didn't have time to try to learn to fix as I am with prioritized project. Thanks for your help any information appreciated.

Where are you located? Can you help with mine?

How much do you charge for this

Just want to fix my rpm and mph needles but im not sure if the LEDs are the ones that go bad or just the solder?

@TunerwithKids

2 жыл бұрын

LED go bad.

@TheEclipsegsx98

2 жыл бұрын

You're awesome bud! Thank you very much

How much for the blue needles cluster

@TunerwithKids

3 жыл бұрын

I’m probably posting it for $300 shipped on eBay. If they want to return a core, I’d pay $50 for old one if it’s working condition.

damn i really want to do it as the needles on my car are going out, but I have neither the tools nor the experience to solder leds :(

@TunerwithKids

3 жыл бұрын

easy...gotta attempt it man. I've been doing car stuff soldering for 20+ years on all my projects.

Where to go to purchase these LEDS

@TunerwithKids

2 жыл бұрын

Check links in description box.