Welcome to the entertainment industry. Everything is a secret. You're like a magician that is sharing the secrets. You're going to make a lot of people scared, but I'm glad you're here. Thank you for what you do.

1/2” plywood? Have you seen MDO its medium density overlay, its amazing to work with, its basically a plywood lined with a thin layer of mdf on both sides.

I am a new subscriber, thank you for your video's!! I have been looking all over for a way to build this square arch and I have finally found it through your video!!' Thank you again and much success ❤❤❤😊😊

Thank you for your kindness! You are the only one who wants to teach us without charging. Thank you you have a forever follower 🙋🏻‍♀️

Awesome job! I love watching your videos.

The nesting storage design was the surprise ending! Have you considered wearing a respirator to protect your lungs for long-term exposure when routing, cutting, sanding, etc.?

@woodshopbox

2 ай бұрын

Appreciate you watching to the end 👍. And thank you for your concern about my health, I try to use my respirator as often as possible, it’s just when I’m filming it’s off, but I should probably wear it any way

@maau6179

Ай бұрын

We want you around for a very long time 🎉

Love that you have an open door policy to ask questions. I will subscribe for this reason. Thanks for sharing.

@woodshopbox

3 ай бұрын

Thank you, I appreciate it 🙌

What type of wood do you use? All your videos are great.

This is beautiful & thank you so much for your content I will be doing this Today 🎉

Great job as always

Great ideal, nice job.

@woodshopbox

3 ай бұрын

Thanks 👍

very good job !

You are amazing thank you

Nice job

@woodshopbox

3 ай бұрын

thank you!

Hi there, you truly make it look way easy . Can you provide the measurements please

Love it! Are there any measurements?

Отличная работа 👍 Говорите по русски?

What size boards / plywood u use for this kinda projects ?

hi what are the black plastic corner brackets u used to hold the plywood pieces before u nailed them together? 3D printed??

This is so good where are you located.

At 1:31 what is the name of the black tool you are using to keep the pieces in standing at 90° angle?

what are those little black corner holders you use to hold the boards in place while you nail them ?

1:33 I need these corner clamps. What brand are they? Thanks!

Do you have plans for this that I could purchase?

What are the pieces used in holes to lock it in place that were cut out

Okay I’m watching this bc I want to build pillars that will be used for a circus entrance. It will be two 4x4x8ft so all sides closed. But I want it to be collapsible how would I do that?

@mariahpeterson524

Күн бұрын

Mmm I think the same method you used to attach the top piece to the two sides would work. It will come apart at the 4ft mark.

What kind of plywood you use???

Do you use a Brad Nailer or Finish Nailer on most of your projects?

@woodshopbox

3 ай бұрын

I use brad nailer for everything, got it first and kind of stuck with it, but the finish nailer probably would be a good addition

Do you sell these?

How do we go about getting the measurements?

@woodshopbox

3 ай бұрын

haven't created any plans yet

How many 4x8 plywood boards did you use for this project?

@woodshopbox

3 ай бұрын

I used three boards per each arch

@osvaldomares4622

2 ай бұрын

Wide it's 16 inch ?

Is that a Table Saw?

@woodshopbox

3 ай бұрын

Yep, I use small Delta table saw