Great explanation. Thank you.

Recommended battery to connect 4 BO Motor with L293D ? I am having 2 numbers of 18650 battery as of now!

Thanks bro,, take your efforts. Very nice, very useful video for beginners.

Very informative video bro....All done perfectly 🥰

thnks bro !! your video was of great help

English accent is too good!!! 🔥👍

Dear I have a project with two motors one use for up and down and second is for left to right, for dish Receiver for Satellite Tracking.. may I use these modules???

can we use mg995 servo and 4 gear motors of 300 rpm to l293d shield?

Great, Thank you.

can i connect 4 dc motors and one servo? if not, then can i connect 4 dc motors in two slots (m1 and m2), and one servo, as i am making a 4 wheel car

If I would use two servos and I give power to Arduino with the USB, can I use a battery pack to power the servos ?

Thanks man!!

which type of dc motor do u use?

Thank you very much I worried a lot to use L293d motor driver with my project because of insuffient information of power supply But this video provides a great detail of different means of using power supply with this motor shield

thank you so much

I have been trying to run 4 motors , but it's going to slow down at very faster with seperate 9v arduino powerup and external power supply of 12v , can you please help me. motor power supply range 3v-6v

Can ardunio be given 12v 2amp Or only 5 to 9v supply

Sir , motor driver shield me motor laganese L293D IC heat kyu hota hai

Is L293D fits with ardrino uno Atmega 328p

Help me , why my obstacle avoiding car not motor not working ?

thank u very much

Even with the jumper out.. when i supply 12 v to sheild .. arduino gets fried

how to control 1 servo and 1 dc motor using l293d motor shield at same time. I watch many video on l293d shield but in all video different motor not run at same time . For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo. But I want to run servo and dc motor together using l293d motor shield. So sir please provide me code for running two different motor ie..Servo and Dc motor same time.

How I connect HM-10 Bluetooth module when using this L293d arduino motorsheld?

Sir can i use four 1000 rpm dc motors with 12v supply in this motor shield? With out facing the heating problem? Because sir i am using a L298N motor sheild but it was heating in 3 seconds like fire Please help can i use L293D instead of L298N?

Super

Can i connect 2 dc motor and 2 stepper motor?

what is the model of this dc motor ?

can i run the motor using digitalwrite ?/

sir , but moters connected to diver moter shiled is not working, plz reply

Boa tarde amigo daria para acionar o Children Como esc para acionar motor brushless bifásico ou sejá três fios.

can we set the road back and forth 10 minutes forward 10 minutes. and set the speed

Sir when I tried to compile code it shows message (FATTAL ERROR AFmotor.h) nosuch file or library .what is reason?.

@sujalkumar3140

3 жыл бұрын

Yes I'm also facing this problem

@a2zcreator109

3 жыл бұрын

af motor library install karna padta h

bro I have connected all four motors to the motor driver shield but connected only 3.57 volt battery and the tyre is not moving is this a battery problem for my motor driver shield is not responding please help me

@himalshadharmapala5530

4 жыл бұрын

I think your supplied voltage is not enough.

thanks bro

does this code allow for turning?

thankyou

bro it getting error in complation dc_motor_test.ino:23:6: error: 'void loop()' previously saying like that plzzz give me solution for it

How many volts is your dc motor?

Can i connect bluethhot module

Bro till how much mah battery we can plug to motor driver shield bro can I use 4.2 v 6000 mah battery of 2psc is the motors works good bro plz give me a solution bro plzz

Can this used on IOT?

Boa tarde amigo daria apaixonar um motor Brushless porque nunca vi ninguém acionando neste motor

How can I connect a bluetooth module on this device? I want to power it using bluetooth. Thanks

@VanshSharma-mo7gu

3 жыл бұрын

Just Connect rx and tx Pin to Pin no. 1 and 0 respectively and Power you can supply with the servo Gnd and positive pins

Me ek project bna raha hn kia ap meri us me help kr skte hen...

Can you do a video showing how to control 4 motors via Bluetooth??

😮

Can this library will be compatible with arduino mega?

@DPVTECHNOLOGY

4 жыл бұрын

yes

Hi, does anyone know if I can use 4 DC motors and 1 SERVO motor at the same time? Thank you for answering

@VanshSharma-mo7gu

3 жыл бұрын

Yes you can

The library that your mintioned is old

When I unplug it from the computer it stops working.

@surajnayakraghuvanshi2495

4 жыл бұрын

I

Can I use it with other litter T,L

Did anybody else worry he was going to fry something on the shield when he was sweeping the 9V leads across it?

Why the speed of the motor is slow ?

@vlektor

3 жыл бұрын

search for the needed voltage for your dc motor and use a power supply with that voltage to power the driver shield

Can I connect 4 dc motor and 1sevo at one time

@DPVTECHNOLOGY

4 жыл бұрын

yes

How cost

أهلاً وسهلاً ومرحباً بك-يتعذر الاشتراك ولا يوجد جرس-يتعذر الاستجابة لكل طلباتك-شكراً لك-يتعذر التعليق- لا أعلم .

Can we make flying drone using this sir

@DPVTECHNOLOGY

4 жыл бұрын

no, you have to use BLDC motor

@SamSam-qc9kn

4 жыл бұрын

sir i mean...can we use this board for making drones

are u assamese??

😂

Video no t claer

Hi, if i use 8 motor. And the output of L293d is only 4. Can i put 2 motor in 1 output? Event it run at same time..

@extras6604

Жыл бұрын

Yes bro, It works. I tried only when 3 batteries in parallel( parallel con adds current) for me. I used 9v battery

Sir , motor driver shield me motor laganese L293D IC heat kyu hota hai

@a2zcreator109

3 жыл бұрын

mera bhi hota h