Works well, thought I had it wrong then realised that I hadn’t put jumper for power. A good teaching video

Very good. I`m still a beginder but I got my motor to spin. I´m happy thank you.

IT GIVES A BASIC IDEA THANK U A LOT

love you-you have fixed all my problems in life.

It is so very much helpful thank you so much Sir.

Great video, it was really helpful!

Invaluable info, thanks very much

GREAT tutorial works great.

Thank you for the video!

Worked awesome thanks!

Sir how to use the digital pins after placing motor shield on arduino. I am currently working on my final year project which is a fire fighting robot and when I put the motor shield on arduino then the digital pins are also covered . Do I have to perform soldering on motor shield

Hi I want to connect 4 12 volt gear motor. Which batter I can use for it

is there any specification to connect motor wires to audrino? ie. black and red can it be any order?

How did you solder header pins on the motor driver shield ? Please reply project pending

when i put off cable from arduino ...the code dose not work with motor control shield,even i connect external 18 volt bettry to the ardunio

Why do you use the power jack? Is it to powe the motor because it draws way too much current and arduino can not handle?

Pls can u tell me how i connect mpu 6050 with motor shield

Much easier than using an L298N bridge. Shukria.

If I would use two servos and I give power to Arduino with the USB, can I use a battery pack to power the servos ?

May i ask what are the pin input in M1 and M2

I chose this tutorial because it is easy to understand and it slowly points to the different parts I liked because we also understood better how to use a motor shield and for me it was a huge help.

Great video, worked first go

Maximum amps that the shield board can transmit is ??

is it okay if my H Bridge is not on the top of the arduino?

Very useful, thanks.

Hello congratulations for sharing. I have a roue codeuse on the motor shaft (recovered from a printer).I did the test of 5v pulses sent by the transistor. Could you specify where I have to connect these pulses on the arduino motor shield. Thank you.

thanks man its working good

Great video! I am making a ball launching machine using a 12V 30W motor and a 16.8 Ah Lithium battery. Would this motor shield work with this setup? If not, what's your recommentation? Thanks

I want to use other digital pins in arduino how to use it and the motor shield on arduino

If we have 2 motors one work with 12v and the other one with 9 v how can we use the shield

can I contol the speed of DC motor with Arduino pwm by simulink(MATLAB)

how to know (max) input motor shield and output....im stp help me!!!

Why the additional power supply is connected to the arduino and not to the shield ?

Thank you sir..excellent workingg,

I have KA03 motorshield is the code compatable for my shield?

How did you power the motor shield and Arduino

not getting enough power from motor shield to drive my motor. how to get more power output from motor shield ?

Thank you sir..

How to setup pins for 4 motors With arduino nano

how to control 1 servo and 1 dc motor using l293d motor shield at same time. I watch many video on l293d shield but in all video different motor not run at same time . For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo. But I want to run servo and dc motor together using l293d motor shield. So sir please provide me code for running two different motor ie..Servo and Dc motor same time.

Just brilliant

What type of motor shield did you use?

Thanks u so much buddy

Hello sir my ardrino shield start making beep sound and gives very less power that even can't run the motor plz help

Thanks, good job, make sure that you motor does not pull more than 0.6 A

can I use this motor shield for quadcuptar mini brushless motor

@shyamsundarsaravanan7398

6 жыл бұрын

+Creative Bong Nope! You should use an ESC (electronic speed controller)

very good helpful thank you

Sir i need help when im useing AFMotor code it is not working king

THANK YOU !!!

sir i want please upload, how to connect hc-05 bluetooth to arduino uno,i had totally confused.

I liked this video very much and usefull can you put the video of how can we connect hc 05 in arduino and motor driver shield for rotaiting the dc motor

What means if led doest not turn on when I connect the af motor shield with. Arduino .. please reply me fast bro

@shyamsundarsaravanan7398

6 жыл бұрын

+Mechanic 27 Connect it as shown in the video.

What is PWR in motor shield

Bro can you give link of motor driver A0-A5 you're inserted pins please bro

thank you so much

How to use it with joystick?

Nice explanation. I have one doubt. Why you have given power supply to Arduino board but not to motor shield? What if I power the arduino by usb and connect the power supply to motor shield? What if I power the motor shield only and not connect the usb?

Thank you sir

Very useful video.......Shyam.......👍👍

Bro which wires are those please someone asnwer

Thank you very much, managed to power 4 dc motors and got the bot running fine

@ravipathak3679

6 жыл бұрын

same here

@ravipathak3679

6 жыл бұрын

.

@mhenzine

6 жыл бұрын

I want to ask doubt can you please give me ur contact number

@Xyzqwj

5 жыл бұрын

Falliant quelnath can you tell me how did you power your arduino and motor shield?

what is the motor used

Excellent

Bro please help me ma code upload krne ke bad bhi nahi chal rhi ak bhi gear motor

Ye btao steper or dc ko ek sath kase chlaye code

If you have to attach some jumper wires to Arduino how you can connect wire with Arduino.

@shyamsundarsaravanan7398

6 жыл бұрын

Only digital pin 2 can be used. You can solder a header pin in the given hole in the motor shield.

why do I get the following error: call to 'AF_DCMotor::AF_DCMotor(uint8_t, uint8_t)' uses the default argument for parameter 2, which is not yet defined Has AdaFruit changed their library? Any information would be gratefully received.

@treereaverjones6535

6 жыл бұрын

OK. Sorted. There has been a change in the software. A sketch for my 2 year old obstacle avoiding robot works and it was compiled 2 years ago with the line : AF_DCMotor motor1(1); but this same line fails now. Using the lines: AF_DCMotor motor1(3,2); AF_DCMotor motor2(4,2); compiles and works on my grandson's tank. I suppose the second parameter is useful but since Adafruit don't support the board I can't see many people not being caught out by it.

@shyamsundarsaravanan7398

6 жыл бұрын

+Treereaver Jones The second parameter is for frequency (speed of the control signal)

@treereaverjones6535

6 жыл бұрын

Thank you for this. But it doesn't explain why a sketch, even Adafruit's own examples, now fail to compile. Whereas they always used to, without the second parameter. I am not very good at coding so I don't have much time for sketches/programs that don't work. Nor do I understand the complexities of .h and .cpp files so I have to rely on expert advice and I am very thankful for it!

Can you demostrate wit Pro MINI pllease?

Please help brother, my dc motor is not working using this af motor shield.

@alexanderalex3692

4 жыл бұрын

neither mine

Can i connect bluetooth hc05 to the arduino with this motor shield?

@ahamatibrahimhassan3265

5 жыл бұрын

WHAT HAVE U DID OF YOUR PROBLEM

what pins from Arduino Uno do the motor shield use.i want add some other components leaving the pins used ???

@shyamsundarsaravanan7398

6 жыл бұрын

+leeladharesh leela you can use the digital pin 2

@leeladhareshrock7578

6 жыл бұрын

I wanted to use the LCD display. so can I do it with which pins...

@shyamsundarsaravanan7398

6 жыл бұрын

+leeladharesh leela no you cannot. Buy a L293D board. Robodo Electronics L298 Motor Driver Module www.amazon.in/dp/B00N4KWYDE/ref=cm_sw_r_cp_apa_i_YzPAAbTXP8F44

how to use the other digital pins in DK electronics motor shield

@shyamsundarsaravanan7398

7 жыл бұрын

+Umesh Talekar You can use the Digital Pin 2. Just Solder a single male header pin in the given hole.

Plz make HD video video I can't see programing

Thanq so much bhaya We love u so much You have helped me so much

Bro , how to avoid thermal failure ?

Awesome tutorial! can the board drive more than one dc motor

Hi sir I am watching video tutorial is awesome or resolve my half problem but how to connect with Bluetooth app

@ahamatibrahimhassan3265

5 жыл бұрын

HAVE YOU GET SOLUTION OF YOUR PROBLEM?

@ku8721

4 жыл бұрын

I too would like to know that solution!!!

How much power supply??

i tried this but had no luck :( "avrdude: ser_open(): can't open device "/devttyACMO": no such file or directory"

@shyamsundarsaravanan7398

6 жыл бұрын

+Junior Cabrera Select the correct COM port.

@anantrathi373

6 жыл бұрын

same here

@ejay620

6 жыл бұрын

pokemon pekka busters you have to manually change the setting in the arduino ide in the port tab

Good

The board has ONE configurable component - the PWR jumper - and it isn't mentioned!When the jumper is installed power is supplied from the Arduino 9v supply. The plug for this supply is visible in the video, below the motor shield, when the motor is operating. When the jumper is removed power is supplied from the motor board +M terminal. This is the recommended mode of operation if using multiple motors or servos. Do not leave the jumper installed if both power supplies are connected: there are no isolating diodes.The description of the LED is unintelligible.

motorshield is not working when I connect arduino

good

👍👍👍👍

Как подключить шаговый мотор от сканера что-бы он играл музыку как на youtube канале floppotron? स्कैनर से स्टेपिंग मोटर को कैसे कनेक्ट करें ताकि वह यूट्यूब चैनल फ्लॉपोट्रॉन की तरह संगीत बजाए? How to connect the stepping motor from the scanner so that he plays music like on the youtube channel floppotron?ff

Ok, so what is the minimum voltage I can apply to the shield?

@shyamsundarsaravanan7398

6 жыл бұрын

Anywhere from 7-24V.

it works

@mhenzine

6 жыл бұрын

I want to ask doubt can you please give me ur contact number

My friend is very, very good projet vidéo

Bro I am getting 'the system cannot find the file specified' error what to do

@shyamsundarsaravanan7398

6 жыл бұрын

+TD channel Try extracting the library zip file and put in the Libraries folder.

u shud talk about the code too, as what those lines do and what are possible lines of code tht is impportant to remember?

sir thank much very sirr

Great Working well . How to control code for 4 dc motor . Copy and paste and change motor no . Please help for 4 axis robot . How to remove loop

tq sir

nice video bro how to connect 4 motor with arduino nano

Apne mere quest ka answer kyo nahi dia

how to control power window motor using motor shield

Please reply for that

how to connect 4 motor with arduino nano & how this code

@Thinkdifferentsagnic

5 жыл бұрын

Rakib Sarkar You can use a ULN2003 IC with arduino nano or you can use a l293D or l298 motar driver.

Arduino: 1.8.10 (Windows 7), Board: "Arduino/Genuino Uno" sketch_nov16a:1:9: error: AFMoter.h: No such file or directory #include ^~~~~~~~~~~ compilation terminated. exit status 1 AFMoter.h: No such file or directory This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.

@shyamsundarsaravanan7398

4 жыл бұрын

It's #include