Thank you JB for all the great videos

@GarageGear

11 күн бұрын

@@harishdevi4344 you got it my friend! 👍

Cleaned the carbs on my two jx75s today. Thanks for the video!

@GarageGear

4 жыл бұрын

Colin White glad this helped you out! Thanks for watching!

Great educational video. Thanks!

@GarageGear

6 ай бұрын

Appreciate the positive feedback Larry! Thanks for watching!

Good video but you forgot to remove and clean the low speed jet. It is located on the top of the carburetor by the idle adjustment screw. It has a couple of cross drilled ports and a very small port in the end of it that clogs very easily.

@GarageGear

3 жыл бұрын

Thanks for the tip! Thanks for sharing Scott!

Great video. Cleaned my jx75 today and it works great now!

@GarageGear

4 жыл бұрын

adam vernier thanks bud! Glad this video helped you out! Thanks for watching!

@adaverni

4 жыл бұрын

@@GarageGear Do you happen to know where I can get new gaskets? Best option I've found so far are kits that come with a whole new carb.

@GarageGear

4 жыл бұрын

adam vernier errr... that’s a tough one. I’ve had some luck with green parts direct in the past but a lot of times I just scout eBay. Warning! Prices are usually high for these little parts and pieces. Mainly because they are going extinct lol. If you need anything else or are interested in used parts email me at garagegearjb@gmail.com I sometimes get parts for these. I can sell them to you through PayPal. Let me know and thanks for watching!

Great video! Why not pull and clean the pilot/idle jet while your at it?

@GarageGear

2 жыл бұрын

Hey Tuss, you could do that as well. I have cleaned 100’s of these carbs over the years and only found it to be a major issue once. Main culprit is usually the emulsion tube an jet on the bottom. Thanks for watching Tuss!

Any tips or anything online that would help get my cables correct?

@GarageGear

3 ай бұрын

Which cable has an issue?

I just have to ask how do you know which Mikuni carb you have or are they the same for many models. It is on a FB460V-BS00 . Also the clear tube on this carb I don't have or know what its purpose is. Help!!!!

@GarageGear

3 жыл бұрын

Great questions Keith! These carbs are all pretty much the same. They all function pretty much the same and maybe have only a few cosmetic differences. They all clean the same way too. As far as the tube goes I’m not 100% sure it’s purpose. It’s either a fuel overflow because I’ve seen coming out of one before or it’s an air intake. Fuel should not be leaking out of this tube. If you have any more questions let me know thank you for checking out my channel!

I’ve always followed the game plan Clean the exterior first then start removing parts

@GarageGear

6 ай бұрын

It’s a smart plan! 👍

Cleaned out my JX75 the pin holding the float wouldn’t come out so I could get out the needle. Cleaned out the rest of the carb and put back into mower. Gaskets and o-ring was in good shape but the mower still hunts, do you think the needle would be the cause of the hunt. When I blow in the gas inlet the float works and when needle is closed it doesn’t allow air through. Trying to figure out why it’s still hunting? Could it be hunting from the throttle pin? I didn’t clean that.

@GarageGear

4 жыл бұрын

Les Branton I would check that needle again. Usually once you get all the parts clean those things run really well. Could always get a new needle and float and it should work even better probably. Also check the throttle pin by adjusting it a quarter turn at a time to see if that helps. Don’t adjust it too much. Just play with it a little. And see how it goes.

Hey JB, I’m having trouble with my jx85. When I go to Choke it the choke stays stuck . Also the speed stays all and full and doesn’t slow done , but only shut off the engine. Right now I don’t choke it so it runs right, but would like to get it fully functional.

@GarageGear

3 ай бұрын

Sounds like you need to loosen up or check your linkages. Give them a look to see if something is holding them up.

Thanks for this video. I have a John Deere LX 178 with the Kawasaki engine. I replaced the carburetor in 2018 with a genuine Mikuni carb. Ran great until last year. I watched several youtubes and worked through how to take it apart and clean it. Ran great all last summer. Now, however the mower will run for 20 minutes and then die like it it not getting fuel. I have taken the carb on and off so many times now that I could probably do it blindfolded. Question is how do you adjust it - assuming I have something out of whack? I am able to adjust the idle screw while running - is there another adjustment? It also surges when the mower is disengaged. I am not sure what to try next?

@GarageGear

2 жыл бұрын

Great question here Rob. Tough part is I really need to see it in person to tell. Is the newer carb like the ones in this video?

@robrogers331

2 жыл бұрын

@@GarageGear Very similar. I took it a

@robrogers331

2 жыл бұрын

I took it apart again yesterday mimicking what you did. It ran great for about 5 minutes - cut half a row of grass and then sputtered and died. I can restart it - then it sputters and dies. There is the one screw that has a black plastic limiter cap on it that allows me to turn it about 3/4 of a turn before the plastic contacts the metal and stops the turn. I can turn that while it is running by pushing with a screwdriver - I couldn't tell that it did anything. If I knew it was the carburetor - I wouldn't hesitate to replace as I don't think you can get this quality of engine for an affordable price these days. The surging was not occurring yesterday. The float did not have anything in it. The needle just drops down in the hole and appeared to be making contact with the float. SO....you could write a book about what I don't know on engines in general. Just became a thing with me to fix my own stuff when we had to start working from home due to company protocols. Fixed the Dryer, Fridge Water Dispenser, New Water Heater - but the Mower has me stymied.

@GarageGear

2 жыл бұрын

@@robrogers331 hey Rob! The throttle adjustment screw with the black plastic cap is adjustable. If you moved it you will have to set it back to normal. Put it somewhere back in the middle and start the engine up. Then adjust it to bring the throttle up or down. I’m not sure what the rpm’s on your model must be but if you have an hour meter you can hook that up to it and set them to where they need to be. Can probably find your rpm’s online somewhere. Play with that adjustable screw and let me know what happens! 👍

How to change drivebelt for this same John Deere mower model?

@GarageGear

3 жыл бұрын

That is a tough job. Especially if parts are seized on. Here’s how I’ve done it twice in the past and if there are easier ways out there I’d love to hear them. Remove the blade and blade brake clutch. Loosen the engine bolts. Remove the blade brake clutch spring. Change the belt out and relighted the engine mount bolts. Put on your bbc again. Take the bbc spring and put it in a vise. Bend it side to side and insert quarters or washers in between its rings to lengthen the spring. Once you’ve made it long enough, reconnect the spring to the deck hook and bbc. Then remove the washers or quarters you used. Put your blade back on and you should be good to go. Kind of a tricky job. Hope this helps. Thanks for checking out my channel.

@MrWanenglee

3 жыл бұрын

@@GarageGear thanks

Thanks for this nice video! Any thoughts on how to remove a difficult main jet from a JX75 Mikuni carburetor? I tried with a regular screwdriver and it mangled the slot of the soft brass main jet. I couldn't find a main jet for sale, so I bought a used JX75 Mikuni carburetor and asked a machinist to remove the main jet for use in my carburetor. He also mangled the slot.

@GarageGear

4 жыл бұрын

Indiana Innovation sounds like that main jet is really in there. In the past if they were stuck, I would just hose them out really well (for at least a minute) with carb cleaner. Just stick the carb straw inside and start spraying. Usually if it’s stuck I just spray and pray lol. See how it works and keep me posted. Thanks for watching!

@indianainnovation8002

4 жыл бұрын

Thank you very much. I'll try the carb cleaner. I had sprayed with PB Blaster and let sit overnight before trying to remove the main jet, but that didn't help.

Is that carburetor just like the one that goes on the John Deere GX75- Kawasaki 9 horse. rider maybe similar but smaller?? There was also the RX75 and SX between about 1987 through 92? Really small mine has a 30-in deck engine behind the rider I have more time than money to pay the dealer💸💸 like you I'm afraid I'll screw something up. I do know those Kawasaki motors are bulletproof and run great for many years when they're all cleaned up!! Thx✌️

@GarageGear

Жыл бұрын

Hey Yukon Jack! Not sure if it’s the same carb that goes on a GX75. Those Kawasaki motors are without a doubt bulletproof! Thanks for watching!

I use Just Break Cleaner and it will not eat up any rubber on any carb Very Safe And it is the same as Carb Cleaner

@GarageGear

3 жыл бұрын

Good tip! Thanks for sharing Archie!

Took our John Deere 14SB mower in to Mower repair people..two times in Maplewood used it a couple of times after each vist and again can not start it. Last time to a place in Metuchen did Carb kit and "clean"..used once after that wont start.. How about a brand new Carburetor..wont it finally solve this curse of an issue?? I see after market Carburetors for peanuts ? $20 ..what kind of Carburetor can that be for $20 ?? But the OEM John Deere made by Mikuni..sold by Kawasaki to John Deere and then marked up yet again by Deere..then sold by JD dealers..totals $125 for the Carb ?? A bit too much for a piece that may not solve my no start/hard to start issue..? What do you think Garage Gear ?

@GarageGear

3 жыл бұрын

merseybeat1963 hey there! There is quite a bit of mark up on parts for these nowadays. You could potentially try buying a used mikuni carb on eBay and clean it yourself. I’ve seen them on there for about $30-$60 depending on condition and what’s included. Paying a John Deere place is going to empty your wallet faster than those mowers cut! Hopefully this helps you out!

I cleaned one of those carbs this past weekend, and the needle felt off the float, i noticed the need has a thin wire that hook up on the float tab, but I was wondering if are these needles go on one specific way on the float tab? Or it doesn't really matter?

@josem.2909

4 жыл бұрын

Is just that my mower run rich now, air filter is clean, and clean carb now, so, i don't know... is there any adjustment screw I can turn in or out?

@GarageGear

4 жыл бұрын

Hey Jose, the needle can go on either way and it should be fine. Just slide it on the float. Thanks for watching!

@GarageGear

4 жыл бұрын

There should be an adjustment screw on the top of the carb. A flat head screw driver should fit it. I think some of the very old ones did not have that gold-ish looking screw on top.

@josem.2909

4 жыл бұрын

Garage Gear yeah I checked that screw and it was all the way in. Turned out 1-1/4 turns (as I heard on another video) and it runs fine now.

@GarageGear

4 жыл бұрын

Great! Excellent to hear! Those carbs are great to work on!

Very Good!... 45🐄🦉🏴‍☠✝

@GarageGear

2 жыл бұрын

Thanks for watching Carl

14sb John Deere push mower selling in my hometown for $40, I'm thinking,...

@GarageGear

4 жыл бұрын

Good mowers. Fairly easy to repair and get up to speed. Only issues I find with them is in the blade brake clutch. They are expensive, and time consuming. Transmissions never fail though.