JKS Sway Bar Quick Disconnects Jeep Gladiator Wrangler JT JL
Buy them here! amzn.to/2R9enGJ
Жүктеу.....
Пікірлер: 37
@c130aviator3 жыл бұрын
Shout out to www.badattitudeoffroad.com for providing me the parts. Awesome shipping, awesome customer service.
@tombaffa93743 жыл бұрын
Good to hear from you again! Hope you and your family are doing well.
@c130aviator
3 жыл бұрын
Thank you sir. We are doing well, just tired of the lock downs and masks.
@AlejandroSanchez-qo8qy2 жыл бұрын
Definitely helped me installing mine! Thanx for uploading 👍
@randycarter45293 жыл бұрын
Good stuff! Good to see you back.
@c130aviator
3 жыл бұрын
Thx
@vinuezaer3 жыл бұрын
Hope the bushings on that kit have improved. Mine (on my TJ) started too fall apart every 3 years or so. Company will sell you bushing replacements but they are hard to press in.
@c130aviator
3 жыл бұрын
I have a set on my 2004 tjr. Never needed bushings. Still on the same set.
@CheaperJeeperTV3 жыл бұрын
Too funny! I am behind you in schedule. I'm researching doing this as well. I did my full width RR HD bumper if you wanted to check it out the look compared to your RR HD Stubby width. Cheers.
@c130aviator
3 жыл бұрын
Cheers
@Chineli092 жыл бұрын
If I have the Mojave with no 2.5 lift just the stock suspension can I still slap them on or should I wait to lift it ?
@icehole5033 жыл бұрын
Man our JT's mod list's are so very similar.. I have had these since I did my lift. -bastage
@c130aviator
3 жыл бұрын
Nice. I recognize you. Great minds think alike.
@randycarter45293 жыл бұрын
I am a little concerned about cutting the bracket on the passenger side. Are there any concerns with respect to the strength of the pin bending the brace?
@miguelchacon17453 жыл бұрын
Brandon now that I have my lift on I am going to do this instead of what I had before...I don't have a tool to cut the bracket so that sucks
@c130aviator
3 жыл бұрын
Use a cheap dremel with a cutoff wheel. 20 bucks.
@miguelchacon1745
3 жыл бұрын
@@c130aviator my wife has a dremel tool and I’m going to get a cutoff wheel
@miguelchacon1745
3 жыл бұрын
@@c130aviator I didn’t see a link to the JKS quick disconnect? Do you have one I’m not sure if that’s how you get paid for advertising
@gvsukids3 жыл бұрын
would it be good to widen the hole that the pin goes in so there isn't as much force needed/worrying about dropping pin on ground?
@c130aviator
3 жыл бұрын
Grease it. I wouldnt widen the hole. Make sure you are on level ground. It will line up easily.
@edwintorres58503 жыл бұрын
Do you have like a quick disconnect sway bar end links on the rear of the gladiator?
@c130aviator
3 жыл бұрын
I removed the rear sway bar.
@JLLIFEOFFROAD3 жыл бұрын
hate unbolting sway links. Misty still needs s set the works with her new axle. Iv been using MC. know what would of made the cut quick n easy???? yep a plasma cutter :) lol
@c130aviator
3 жыл бұрын
Acetylene 😁
@JLLIFEOFFROAD
3 жыл бұрын
@@c130aviator ur not wrong, but a plasma cutter would be a little easier in tht tight space 😂😂
@CheaperJeeperTV3 жыл бұрын
By-the-way...did you mention there is some part or bracket that can be used instead of cutting the metal tab? Can you provide me with a link to that info? Thanks
@@c130aviator You're amazing. Thanks for the quick reply. For the cost, I'll just cut the tab too. I was concerned that maybe the piece remaining wasn't very thick, but I'm sure it's ok.
@miguelchacon17453 жыл бұрын
I did it I cut my steel piece of my gladiator to install my quick disconnect
@c130aviator
3 жыл бұрын
Thanks for the update. I am glad you were able to get it. Its not a bad install. Just make sure those bolts and slip pins at the axle are super tight or they will rattle.
@johnthibodeaux51893 жыл бұрын
Is there a way to install this without cutting anything?
Пікірлер: 37
Shout out to www.badattitudeoffroad.com for providing me the parts. Awesome shipping, awesome customer service.
Good to hear from you again! Hope you and your family are doing well.
@c130aviator
3 жыл бұрын
Thank you sir. We are doing well, just tired of the lock downs and masks.
Definitely helped me installing mine! Thanx for uploading 👍
Good stuff! Good to see you back.
@c130aviator
3 жыл бұрын
Thx
Hope the bushings on that kit have improved. Mine (on my TJ) started too fall apart every 3 years or so. Company will sell you bushing replacements but they are hard to press in.
@c130aviator
3 жыл бұрын
I have a set on my 2004 tjr. Never needed bushings. Still on the same set.
Too funny! I am behind you in schedule. I'm researching doing this as well. I did my full width RR HD bumper if you wanted to check it out the look compared to your RR HD Stubby width. Cheers.
@c130aviator
3 жыл бұрын
Cheers
If I have the Mojave with no 2.5 lift just the stock suspension can I still slap them on or should I wait to lift it ?
Man our JT's mod list's are so very similar.. I have had these since I did my lift. -bastage
@c130aviator
3 жыл бұрын
Nice. I recognize you. Great minds think alike.
I am a little concerned about cutting the bracket on the passenger side. Are there any concerns with respect to the strength of the pin bending the brace?
Brandon now that I have my lift on I am going to do this instead of what I had before...I don't have a tool to cut the bracket so that sucks
@c130aviator
3 жыл бұрын
Use a cheap dremel with a cutoff wheel. 20 bucks.
@miguelchacon1745
3 жыл бұрын
@@c130aviator my wife has a dremel tool and I’m going to get a cutoff wheel
@miguelchacon1745
3 жыл бұрын
@@c130aviator I didn’t see a link to the JKS quick disconnect? Do you have one I’m not sure if that’s how you get paid for advertising
would it be good to widen the hole that the pin goes in so there isn't as much force needed/worrying about dropping pin on ground?
@c130aviator
3 жыл бұрын
Grease it. I wouldnt widen the hole. Make sure you are on level ground. It will line up easily.
Do you have like a quick disconnect sway bar end links on the rear of the gladiator?
@c130aviator
3 жыл бұрын
I removed the rear sway bar.
hate unbolting sway links. Misty still needs s set the works with her new axle. Iv been using MC. know what would of made the cut quick n easy???? yep a plasma cutter :) lol
@c130aviator
3 жыл бұрын
Acetylene 😁
@JLLIFEOFFROAD
3 жыл бұрын
@@c130aviator ur not wrong, but a plasma cutter would be a little easier in tht tight space 😂😂
By-the-way...did you mention there is some part or bracket that can be used instead of cutting the metal tab? Can you provide me with a link to that info? Thanks
@c130aviator
3 жыл бұрын
www.quadratec.com/p/synergy-manufacturing/front-sway-bar-link-relocation-brackets-wrangler-jl-8855-02
@CheaperJeeperTV
3 жыл бұрын
@@c130aviator You're amazing. Thanks for the quick reply. For the cost, I'll just cut the tab too. I was concerned that maybe the piece remaining wasn't very thick, but I'm sure it's ok.
I did it I cut my steel piece of my gladiator to install my quick disconnect
@c130aviator
3 жыл бұрын
Thanks for the update. I am glad you were able to get it. Its not a bad install. Just make sure those bolts and slip pins at the axle are super tight or they will rattle.
Is there a way to install this without cutting anything?
@c130aviator
3 жыл бұрын
Only if you buy the synergy relocation bracket
U skipped most of the installation…