I'm already seeing so many of your videos that will be helping my '95. Thank you

@Poweraddicts

Жыл бұрын

Glad to hear it! You are very welcome!

Finally get 2 leave a comment Chuck. Bought a 87 yj. Then a 87 Rusty ole yj for parts started fixin the interior up. Nice jeep hardly any rust on the Blue 89 the red 87 is gone ! Even whats left of the frame. My first time having any jeeps. I am learning every day thanks to your video s + KZread ! Thanks so much. U have a fan 4 life Eddie Bygod! Ruut

Great Video Chuck!!

Thank you for the info. Great instruction .

@Poweraddicts

6 жыл бұрын

You are welcome! Glad you like it! Have a great day!

Another GREAT video!! I would love to see the same type of video but with one with the Rear Differential with Trac-Loc: Dana 35, disassemble and reassemble

@Poweraddicts

6 жыл бұрын

If the oppurtunity comes up to shoot a video like that. I will do it. Thanks for checking out the video and taking the time to leave a cool comment! Have a great day!

Great Video Thanks for sharing, I have a 1993 Jeep Wrangler and my jeep makes noise went is running I believe is the differential

Thank you, your explications were simple to understand for me. Bravo !ç

@Poweraddicts

3 жыл бұрын

Glad it was helpful!

I tried getting Google to help me find the amp output on a alternator of a Durango. They were no help but the next day I watchedyour video . went to Rock Auto told them the numbers + i have a 90 amp alternator for 30 dollars ! It may be higher then that ? Thanks from Steady Eddie in Melbourne ! Oh yeah Florida ! ! HaHaHa

Great video! I wish I knew you personally so I could hang out with you and learn more.

@Poweraddicts

6 жыл бұрын

Glad you like the video!! Just watch vids, read and take your time. Knowledge comes from practice. Thanks for the awesome comment!! Have a great day!!

I have a Rear Differential with Trac-Loc: Dana 35, 355 gears. Who makes the best Limited Slip Clutch Kit for my Trac Lok ? Again, GREAT video!!

احسنت التفكير والظن

Thank you!!!

@Poweraddicts

6 жыл бұрын

You are welcome! Have a great day!

@kingsoulsurfer41

6 жыл бұрын

Is it possible for a tension Pulleys make noises?

I am getting frustrated with the power and speed of my 95 2.5 yj with 33 inch tires and 4.11 ratio with a top speed of 55 mph , watching your video gives me an idea of changing my gear and pinion.the question is what ratio should i go with so i can at least cruise at 65 mph ?

Superb video. Very informative - step by step. Thanks! Question: when I turn my driveshaft there's a little play before the wheels start turning. Is this normal? Should there be any backlash or should the wheel move exactly at the same time you turn the drivshaft?

@Poweraddicts

6 жыл бұрын

There is always just a slight bit of movement. How much depends on how much wear the ring and pinion gears may have. So, you will get a bit of driveshaft movement before the wheels move. Hope that helps! Have a great day!

Question what causes a lower radiator hose to pop off

. I need the rear end replaced Im wanting to take out axles, housing an all out of my 2000 cherokee and replace it with another complete housing, axels an all.unbolt u bolts drop it all. What modal jeeps will inner change.

Loving the yj videos, on mine it looks like they flipped the axle over and did a spring over swap. Is it safe to run it that way or will it mess stuff up

@Poweraddicts

5 жыл бұрын

As long as the flip was installed properly it's fine. Many older 4x4s came factory spring over axle. The only catch with the YJs is that you should have an anti-wrap bar on the rear diff to prevent spring wrap under acceleration. Have a great day!

chuck, i have an 89 yj 2.5l 4cyl. im not sure what my ratio is on my dana 35. but i was thinking of getting a locker for the rear. do u recommend it?

I got an 88 yj with the spider gears pinion gears screwed. Is there and upgrade from a later model swap? I have 32 tires

Thanks again, Chuck, but question: I know you are junking this rear end, but for those of us not having another rear end to exchange; in looking at the galling of the saddle housing for the carrier, would it be reusable with a new bearing and race? Is this rear end, in your opinion just junk and should be scrapped or is that your choice? Could it still be reused with any hope of longevity?

@Poweraddicts

6 жыл бұрын

Honestly, not for long term. The shims and the galling of the housing would allow the carrier to move too much in the housing. If I really had to put it back together to use it, without question the shims would have had to been replaced and possibly adding more to tighten it up. A proper fitting carrier needs to be pried out, you saw that one actually fell out. So, overall, the whole diff housing was beyond usable repair. Thanks, that's a good valid question. Hope my answer helps. Have a great day!

Question, when you swapped your rear axles (the 3.55 into your 91) didn't you have to change the ratio of your front dana 30 axle to match? My uncle has a older AMC 20 axle from a CJ7 and I was thinking of swapping it for the 35, but it may be better to just re-gear the 35 and 30. I'm currently running 33X12.50 tires on my 95' YJ and not getting much out of 5th gear.

@Poweraddicts

4 жыл бұрын

I still need to swap front axles to get my gears to match. Because of working what seems to be all the time, I dont get to where much. Within the next couple of months I'll swap the axles to get the gearing to match. You would be better off swapping in an 8.8. The Dana 20 and Dana 35 are both weak diffs.

Count your ring gear teeth then your pinion gear teeth then divide the number pinion teeth into the number of the ring gear teeth and that will be the (exact) gear ratio....

@Poweraddicts

3 жыл бұрын

You are correct. I was being all technical and didn't even think about showing that. Thanks for leaving a great tip for others to see! Have a great day!

Can I have the Carrier I need it so bad mines cracked or I can buy it??

@Poweraddicts

3 жыл бұрын

I scrapped that diff right after the video.

Question what causes a lower radiator hose to pop off