Like always you make this job so easier, i watch you on tiktok in the past but i'm glad that i found your youtube channel, keep up the good work!

So you do not require the JCID programmer if you are using the pre programmed flex?

@bxnny6657

13 күн бұрын

No, you do not need a programmer, however this maneuver is way harder, and as expensive as buying a new programmer.

Dont you just miss the days when you could just slip the back off and pop a new battery in within about 10 seconds.

Apple why the hell did you make it so hard to replace an effin' battery. Learn from TV remote controls and add a gasket to make it waterproof.

@TheSanien

Ай бұрын

To force people to use their own shops so they can rob you again. Good business as most people gladly do it. Apple are scum for parring their components with the logic board which is completely unnecessary.

So, when i replace the bms, i dont must programing.

Hello, I recently got my iphone 13 battery replaced. but the problem is the battery percentage seems to be incorrect. It'll rapidly decrease from 30 to 20 but lasts long enough for a day. Any idea to fix this or should i let it be.

Followed all steps but no luck. The old battery health is still present. iOS 17.4.1. Tag on flex v3.3. Does anyone found a solution on how to reset the cycles and battery health???

@muhammadzubair.1994

3 ай бұрын

You need to flash your phone.

So with the tagon flex I don't need the battery coding machine again?

So basically only one tag on flex is needed for all my repairs? Since I don’t need to leave it in the phone and can reuse it? Does the BMS then just restart and count down again as a new battery?

@iDoctorUK

11 ай бұрын

Yes! I keep a couple for each model but they are 100% removable and reusable

@danielzonozi2042

11 ай бұрын

@@iDoctorUK😮just seems odd that in any other repair they leave them. But that will reduce the cost of changing a battery significantly if it works without

Where do I buy these batteries?

OK! So what is this tag on flex and where can I get one? OK! Did my research and bought a tag for my iphone 12pro, followed your instructions but unfortunately it still said it wasn't a genuine Apple battery?

Is data and backup is lost in the process of battery changing 🤔

At 1:47 u cut the tagon flex but never show what tagon flex you use?

so you actually have the Old cycles from the other iphone without reset the cycles. Won´t work!

Hi , I got a question to you guys so I got both the qianli tag-on flex and the programmer do I need to program it or does it come preprogrammed, and as I understand from this video booting the phone with a different battery is not needed

Hi there, just wanted to ask, what tag on flex do yo buy? cheers

I thought the whole point of soldering the BMS was to avoid the error message - why do you need the tag on flex to be connected first before removing it? I assume if you solder the BMS to the new battery, but don't add the tag on flex, it will still show error messages? I have the same Qian-Li tool and tried this process on an iPhone XS summer last year, accidentally broke the BMS board so ended up just putting in a third party battery since it's now not possible to get around the non-genuine battery warning.

@mechytechy412

2 ай бұрын

The tag on flex will trick the iphone into believing that its the phones actual battery and the phone will read that info from the battery and pair it with the motherboard. The tag on is supposed to link the iphone with the phones motherboard.

@alexshepherd

2 ай бұрын

@@mechytechy412 thank you, I'm a little confused as the BMS was swapped from the phone's original battery. Is the tag-on-flex capable of pairing a new battery BMS with the phone - in other words, is it unnecessary to swap the flex cable if the tag-on-flex is used? Cheers for your advice, very good video

Watching from India ❤

@iDoctorUK

7 ай бұрын

Thank you brother ❤️

Watching from Antarctica ♥️

@iDoctorUK

6 ай бұрын

Sick! How do you Get parts delivered over there?

Fan from India ❤🇮🇳

@iDoctorUK

11 ай бұрын

Thank you for your support 🙏

so easy track

need programmer to this just tag on flex will not show 100% bettery

What is the ideal percentage of isopropyl alcohol to use?

@mudzzyhype5035

5 ай бұрын

I have heard 70% to clean the phone and 90-99.99% for removing leftover adhesive and that is what I currently use.

Will my battery hopefully come set up ready to just install instead of me having to solder and fix it myself?

@user-yw9uc1pw9d

3 ай бұрын

Without an important battery message, not anymore.

I have an iPhone that will keep showing the old data at 88%, I have tried connecting a different battery, rebooting and reconnecting the new battery with the transfered bms board again but to no avail. The new data won't show up whatever I do, have you come into this? I have done many replacements without issues with the same tag on. Thanks in advance for your reply

@zarifhilmy7479

4 ай бұрын

for ios 17.4.1, you might need to restore battery health through 3utools. install the battery with flex to the board and connect the phone to the pc. if the battery in the 3utools showing 100%, you can reset battery health to 100%

@blackrepairs5978

4 ай бұрын

@@zarifhilmy7479 Thanks for your response! It indeed shows 100% in 3utools, how do i reset the battery health to 100%? Can't seem to find any reset battery health option in 3utools

@zarifhilmy7479

4 ай бұрын

@@blackrepairs5978 flash your device. go to - easy flash - quick flash - tick on restore battery health. ( this step will fully reset your device. should backup first. do this step with installed tag-on-flex. after process is done reboot your phone. check the battery health. once shown 100%, can remove the tag.

@zarifhilmy7479

4 ай бұрын

go to easy flash - quick flash mode. tick on the fix battery health. this step will reset your device

@blackrepairs5978

4 ай бұрын

@@zarifhilmy7479 Cheers man, found it. Is this problem only on 17.4.1 that you know? And is there a way without resetting the device, if a client were to come with a phone on the newest iOS at this point repairing with battery health showing at 100% would not be possible as the clients phone would lose the data..

Guardando dall'Italia

@iDoctorUK

5 ай бұрын

Ciao!

No need to use reprogramer like JCID? Just the tag on flex?

@scooterdoo1

3 ай бұрын

You need to purchase a tag on flex that is pre-programmed for the iPhone you are using. You can re-use your existing tag on flex but will need to reprogram it to reset the battery cycles and health. The programmer can cost $100+ so a pre programmed tag on flex is the way to go for a personal diy replacement

So good

Followed all the steps but didnt get 100% BH

@LIVE_FOR_TRUTH86

8 ай бұрын

No need worry may be he don’t show us battery circuit reprogrammed

@samirh8588

6 ай бұрын

@@LIVE_FOR_TRUTH86 Yes, you are right. He do not showi battery activation and battery board reprogramming for which you need aditionaly equipment.

100% battery health is much better.

waching fron india nice video

wait... wasn't the battery replaced from the back of the phone???? Mine back glass is broken i thought need to fix that before i change battery haha

@zakg60

6 ай бұрын

lmao i thouigt that too

Watching from my phone

I did exactly same, step by step, and my condition isn’t 100. It’s 80% as it was before repair. Any ideas? I have used tag on 3,1 version if that’s important

@alanprzyszlak9580

11 ай бұрын

And I had no message about battery :/

@freshboypr

11 ай бұрын

Try put it in 99%

@alanprzyszlak9580

11 ай бұрын

@@freshboypr by using qianli device and software?

is that 70% alcohol? or 95%?

@iDoctorUK

7 ай бұрын

It’s actually 99.9%

But the battery already come with that conector

@iDoctorUK

7 ай бұрын

Most will unless you specifically buy it without the bms. The purpose of this video is to avoid the non-genuine part warning

@soloplayerid

6 ай бұрын

@@iDoctorUK thanks sensei

Thought you needed a special tool to program the battery

@Coopzzz360

6 ай бұрын

You needed a programmer for the previous tag on, these new tag ons are already pre-programmed so no programming required.

@pixeldome3d897

4 ай бұрын

where can i get new tag ones from? The ones that reprogram by itself?

In my opinion this tutorial has too many unnecessary steps to replace the iPhone 12 battery. The iFixit tutorial at kzread.info/dash/bejne/ZaVnydmnfqmneaQ.html is better. Note that I fix it sells the iPhone replacement batteries and they include a very nice set of tools specifically designed for the battery replacement in the Apple iiPhones, MacBooks Tablets etc. California

@MrRawUK

Күн бұрын

You listed the same video lol

Where do I buy these batteries?

Where do I buy these batteries?

Where do I buy these batteries?

@sur.geek333

2 ай бұрын

You can buy them from different vendors / different brands. I get mine from injured gadgets Xcap brand or from gadgetfix . They have no welded needed as well.