It’s really nice to see a board with proper documentation, support and good videos explaining how it works and showing the interfaces. Keep up the good work!

Fantastic controller, fantastic explained, fantastic support!!! I have one controller and I'm delighted!

thank you Makerbase for this helpful exlanation video! 😊👍🏼

Very useful, these videos are helping me a lot, thank you very much

Thanks for this video, nice to see that $ parameters are same as grbl

I have now a DLC 2.0 with TMC 2208 and 2209, DLC 2.1 with MKS TMC 2160 and an XY DLC V1.0 and today ordered the DLC32. Unfortunately it takes 6 weeks for the part to arrive in Germany, but I'm looking forward to it. I am excited Regards Stephan

Very useful video. I am using the twotrees TS2 laser engraver. He can adjust the z-hight via parameter in lightburn and lasergrbl. It would be great when your software would develop this funktion too.

love MKS products,

2 questions, 1, On the laser itself, VCC,GND,PWM are the connections i have, The board (V2.1) says S, TTL, V, are these in the same in order or do the wires need re-arranging? 2, On the MKS Armor, a fan can be installed to cool the drivers, can the fan be connected to any of the 2 12/24v outputs without affecting the laser or does one use a separate power supply? Thanks!

Is the "Spindle" connector a PWM signal? What voltage does it output? Also what is the max freq for this (if it is indeed a PWM)?

Hello. Nice motherboard. Is it possible to use it to replace an old controller board that drove "SGDA 04 servopacks"? For a laser engraving machine (90w co2). Any link for information about this conversion? Thanks

Hello everyone! I am mounting this board to my sculpfun s6 and I wanted to put a power switch on it. How big should the wires be that I have to solder on the PCB to get them to the switch? How many AWG should be the section of that wire? I imagine that all the amperage of the power supply will pass through it. Regards

Can you use this with the mks closed loop steppers without any problems?

Hi Makerbaser Team, what is the function "Open light" and "Close light" in web connection?

Hey, i'm building a cnc and i will use this board. Witch step motor driver do you recomend?, 4 nema 23 motor 2.3A

Hi! Is there the possibility to use a joystick or a keypad instead of touchscreen to move x and y of a laser cnc machine ?

It's a shame that there doesn't seem to be any other source of supply for the set for Germany or Europe. At the moment, you can only buy the DLC32 without a display from Ama***, and you might get an old revision

Can I easily set up sensorless homing and negate the use of endstops by using 2209 drivers on this device?

THANKYOU FOR CLIP VDO. I HAVE ONE QUESION. HOW TO CHANGE FIRMWARE FORM LASER TO SPINDLE MOTOR AT THE "Z" AXIS?

hey thnx for video. Today my cnc 3018 machine's board is broken. can i replace it with this board. my machine 3 axis cnc 3018. your board 3 axis but with two motor drivers. is this compatible?

Thanks for the review! I have several questions: 1. My spindle is 20 volt DC and current = 4.5 A has its own PWM speed controller, can I just turn the spindle on and off from this controller? 2. My normal limit switches have only two pins, can I use them in the controller and how do I connect them to the three pin connector? 3. Can use this controller for milling, need to upload special firmware, then the menu should change?

@3dmixer552

Жыл бұрын

No you cant directly. with a little tinkering you can connect a 12v relay to the spindle output which will switch your 20v to motor.

Hi. I have a spindle with external power supply and external control. What will happen, if I will not connect anything to spindle pins on MKS DLC32 board?

nice

what about probe settings, limit switches and homing

How to pin enable/disable stepper?

Hello and thank you for this video. Is it possible to configure the wireless settings of the board without the screen ? (Can I configure it thru my mac and the use it wireless thru lightburn without any need of the screen ?) Thanks !

@makerbaseteam4217

2 жыл бұрын

Yes, download the latest firmware, you can configure wifi in the configuration file

Hi, i am having throuble to use this board on my co2 laser, how can i contact the support?

wie lautet das standart wifi passwort? wenn ich strom drauf gebe macht der AP ein MKS_DLC wlan auf.

I am using a MKS DLC32 v2.1 as my controller. so here is the problem, it was working last night when I went to bed but this morning the laser does not fire. however it does fire if I enable "fire button". I thought it might be the board so I ordered a new one and are having the same issues. I press start the gantry moves but then it acts like its engraving but no laser and it suddenly stops. Not sure where to go from here... Any ideas what the problem is?

Как привязать эту плату для токарного станка по дереву ? спасибо

Can I see a code to turn on the laser? It will not be used with a laser. Rotation axis supported? (xy and 360⁰ "4th axis" - 3 axes are enough). Thank you for your answer. I already found the max step rate. 250 khz.

@makerbaseteam4217

2 жыл бұрын

Rotation axis? Unsupported

Yo ya estoy esperando mi mks DLC 32

What is the maximum size of NC files for offline control?

Hola he comprado una placa mks 32 bits, y quiero conectar unos dreivers externos a la placa tb6600 , cuales debo poner y como los tengo que poner , no encuentro ningún sitio que lo explique Gracias

How can we solve the problem of the cooling fans is being always on ? Non-stop working! It's not working non stop with the cards of other brands like Ortur AtomStack etc. There must be a way to manage it ? Please help

Tem como acessar mks dlc32 pelo ftp? Access mks dlc32 ftp?

Will this board work on grbl controller app

Thanks for the video. Which motor drivers are used? source of supply?

@makerbaseteam4217

2 жыл бұрын

A4988, TMC2208, 2209 , 2225, 2226; LV8729, drv8825, etc.

@danielbusch2398

2 жыл бұрын

@@makerbaseteam4217 got it. thanks. but now i cannot control the axes individually. only the x-axis works separately. y and z axis just twitch.

How to enable power loss recovery in this board

Is it possible to use it on a corexy machine ?

I have just put this on my K40. Lightburn does not detect it at all yet LASERGRBL does and can operate it (roughly but it moves). Any ideas?

How to do firmware MKS DLC32 board?

Is the display a necessary component to operate the board?

How to use 2 TMC2209 drivers for Y1 and Y2 axis? I really don't understand why there is only 1 connector for Y1 and Y2 polulu driver?

@Claudio-gr4id

11 ай бұрын

Hey, you have a progress with a 2209?

Can make a video for CNC router with this motherboard

@massimomonti8594

2 жыл бұрын

More info about using the MoBo for CNC router are appreciated.I can't find info about using it for milling machine.

Hi excuse the question, the TTL output on the motherboard is maximum at 24w. how is it possible to connect a 40w 3 wire laser? thank you

@makerbaseteam4217

Жыл бұрын

It is recommended that the maximum current should not exceed 20A, the current is too large, you can use the external expansion mos

@alessiovarlotta936

Жыл бұрын

@@makerbaseteam4217 2 or 20 ampere is the maximum corrente? Where Is the correct wiring for external espansion mos?

I've got 2 issues with TMC 2209 and MKS DLC32. Need to know what configuration needs to be applied to avoid step motors jump steps. Someone who can copy&paste best config for nema 17 step motors?

Hello, I have MKS DLC 32 card. There is 1 limit switch slot for each axis. I want to use 2 micro limit switches for each axis. What should the connection diagram be?

@danieldimitrov9411

2 жыл бұрын

Hello i have the same problem how you deal with it?

@mattivirta

26 күн бұрын

one axis connect limit SW paraller, if one connect stop machine,

For me only z axis is not working. And also I cannot see z controls in webapp

@Makerbase Team MKS DLC32 v2.1 board supports dm556 drivers?

@mattivirta

26 күн бұрын

ALL external drivers can use, need only step,dir,enample pins connect.

Quiero cambiar toda la electronica de un CNC 3040, dejaria solo los motores, estoy buscando una placa base y esta con capacidad Wifi es lo suyo ¿solo es para usar con láser?

@makerbaseteam4217

2 жыл бұрын

CNC is also supported

@arfjreyes

2 жыл бұрын

@@makerbaseteam4217 please make one video for cnc routers. I got my dlc32 jogging but not running gcode files.

Too bad they didn't use the board I bought... it has both of the connectors on the bottom right to the display rotated 90 deg. It's in the manual, but it's not marked on the board that I can see.

Bagaimana menghubungkan mks ke power supply RZJG 60W hitam??😢

What is the maximum Khz Frequency it can provide for the stepper motors ?

@makerbaseteam4217

2 жыл бұрын

250kHZ

@BlackwingzYT

2 жыл бұрын

@@makerbaseteam4217 So if i want to use that on co2 laser what is the maximum scan speed i can get using 1/16 microstepping

@BlackwingzYT

2 жыл бұрын

Answer that question plz

@makerbaseteam4217

2 жыл бұрын

@@BlackwingzYT 9000/min

@BlackwingzYT

2 жыл бұрын

@@makerbaseteam4217 I've ordered one without the tft display can i order the display after when i needed one ?

I have a MKS DLC V2.1 board and I bought a 40w laser with 3 wires (red, black and yellow). How to connect this laser to this board?

@makerbaseteam4217

2 жыл бұрын

Hello, the three-wire laser can be connected to the TTL interface on the motherboard, they are S, TTL, G

@tomy8148

2 жыл бұрын

You make it yet? I have idea like you.can you share your machine

@joselitobatista5194

2 жыл бұрын

@@makerbaseteam4217 This board (MKS DLC V2.1) does not have a 3-wire connection. There is only one connection for the red and black wires and another connection for the other two wires as well.

@makerbaseteam4217

2 жыл бұрын

@@joselitobatista5194 In the upper right corner of the motherboard

@minravex9919

11 ай бұрын

​@@joselitobatista5194it hast 3 wires

I would like to chang the control board in a 40w CO2 laser engraver machine, can I use this board?

@makerbaseteam4217

2 жыл бұрын

CO2 laser does not support yet

@marcelomiramon1159

2 жыл бұрын

@@makerbaseteam4217 Que se necesita para hacer compatible, esta placa con el co2 de 40w Saludos y espero

@seabeepirate

2 жыл бұрын

It’s not for the faint of heart but it’s doable. My OMTech k40 is using this board now. If you’re not very comfortable with tearing apart a working machine I wouldn’t recommend going this route.

@Blueyedevil2702

2 жыл бұрын

@@seabeepirate Hey man. I would like to try this. Can you point me to some webpage where to find out how to do this?

@seabeepirate

2 жыл бұрын

@@Blueyedevil2702 There is a clear enough wiring diagram on the Lightburn forums and if you got unlucky like I did your power supply won’t look like the one in the pic. That means you have the “white” power supply, which just means you have to splice some wires or use a specialty crimper to make your own connectors. There is a very good K40 power supply explanation on Maker Forums to help you identify whether yours is a green or white. Don’t feel bad if you think it’s blue. I totally removed the factory digital power control panel with the test button as well as the m2 nano board. Analog is the preferred meter anyway and you can use a potentiometer to limit the max power so it’s not controlled exclusively by software. I used the stock firmware which was newer than the newest download available from MKS. Make sure you set the frequency in your $parameters or your laser might fire inconsistently. Lightburn works on USB pretty reliably. I haven’t tried very hard to use the wifi with lightburn but I believe someone else has figured out how to do this. It’s doable and now that I know how it all works it seems simple but I felt swamped when I wasn’t really sure what I was even trying to look for.

Can I use for Metal Engraving Just Like Iron and Steel

@mattivirta

26 күн бұрын

yes,if use external stepper drivers and big nema 34 motors. smallest motors no power move and cut metal. and need 1,5KW spindle minimum whit steel, smallest can use only aluminium.

motor driver support TMC series?????

its a pitty... its seems in laser mode there is no Z-axis controll?? Is this correct?

@makerbaseteam4217

2 жыл бұрын

With the latest firmware, it is possible to control with the firmware of lasergrbl

@Mr3Dvisuals

2 жыл бұрын

@@makerbaseteam4217 Thanks for the info. What firmware is on the board when I buy one and are there any changes on the pin assignments for the new firmware? Thanks

Support driver motor Tmc2208? 🤔🙏

@makerbaseteam4217

2 жыл бұрын

Supports normal mode, does not support uart mode

Can this be used on a k40 co2 laser?

@makerbaseteam4217

2 жыл бұрын

not support

@FinalFight08

2 жыл бұрын

Not supported..? MKS DLC 2.0 works why this one dosen't work?

@makerbaseteam4217

2 жыл бұрын

@@FinalFight08 Is your CO2 laser tube machine? It's just a machine that can support the laser head

@FinalFight08

2 жыл бұрын

@@makerbaseteam4217 MKS DLC 32 as a TTL pinout that gives 0-5V..that can be connected to GND and IN pinout on K40 power supply to control it...and yes i have an K40 CO2 laser machine 👍. One thing that would be great is that we could change the $33 value on GRBL firmware. Make GRBL-LPC to be supported by the board 👌

@makerbaseteam4217

2 жыл бұрын

@@FinalFight08 Well, we did not conduct such a test, if the previous DLC motherboard works, then it is also possible

Fix the WIFI!

SORRY. QUESTION

Does not remember WIFI credentials. Shame!

this model down not support laser tree brand

lmao, so many questions and no one answers. Not recommended!

DO NOT BUY THIS BOARD!! Makerbase has given up on it and is no longer maintaining the firmware

Three-axis board with only two-axis control. What a piece of junk.

Who would use it with diode. Show it with real laser like at least k40 ! Not some toys !

Bunun güncel hali yok mu? Ürününüz satılıyor ama sorun çözümüne dair hiçbir doğru bilgiye ulaşılmıyor. Aylarca aramama rağmen doğru bir bilgiye ulaşamadım.